+guru|guru-33|guru+unk|ann arbor guru/33 lines 80 cols,
+ lines#33,
+ flash=\E[>59h$<100>\E[>59l,
+ is2=\E7\E[255;0;0;33;80;80p\E8\E[J, is3=\E[>59l,
+ rmcup=\E[255p\E[255;1H\E[K, smcup=\E[33p, use=aaa+unk,
+guru+rv|guru changes for reverse video,
+ flash=\E[>59l$<100>\E[>59h, is3=\E[>59h,
+guru-rv|guru-33-rv|ann arbor guru/33 lines+reverse video,
+ use=guru+rv, use=guru-33,
+guru+s|guru status line,
+ eslok, hs,
+ dsl=\E7\E[;0p\E[1;1H\E[K\E[H\E8\r\n\E[K, fsl=\E[>51l,
+ rmcup=\E[255;1p\E[255;1H\E[K, smcup=,
+ tsl=\E[>51h\E[1;%p1%dH\E[2K,
+guru-nctxt|guru with no saved context,
+ smcup=\E[H\E[J$<156>\E[33p\E[255;1H\E[K, use=guru,
+guru-s|guru-33-s|ann arbor guru/33 lines+status,
+ lines#32,
+ is2=\r\n\E[A\E7\E[255;1;0;33;80;80p\E8\E[J,
+ smcup=\E[33;1p\E[255;1H\E[K, use=guru+s, use=guru+unk,
+guru-24|ann arbor guru 24 lines,
+ cols#80, lines#24,
+ is2=\E7\E[255;0;0;24;80;80p\E8\E[J, smcup=\E[24p,
+ use=guru+unk,
+guru-44|ann arbor guru 44 lines,
+ cols#97, lines#44,
+ is2=\E7\E[255;0;0;44;97;100p\E8\E[J, smcup=\E[44p,
+ use=guru+unk,
+guru-44-s|ann arbor guru/44 lines+status,
+ lines#43,
+ is2=\r\n\E[A\E7\E[255;1;0;44;80;80p\E8\E[J,
+ smcup=\E[44;1p\E[255;1H\E[K, use=guru+s, use=guru+unk,
+guru-76|guru with 76 lines by 89 cols,
+ cols#89, lines#76,
+ is2=\E7\E[255;0;0;76;89;100p\E8\E[J, smcup=\E[76p,
+ use=guru+unk,
+guru-76-s|ann arbor guru/76 lines+status,
+ cols#89, lines#75,
+ is2=\r\n\E[A\E7\E[255;1;0;76;89;100p\E8\E[J,
+ smcup=\E[76;1p\E[255;1H\E[K, use=guru+s, use=guru+unk,
+guru-76-lp|guru-lp|guru with page bigger than line printer,
+ cols#134, lines#76,
+ is2=\E7\E[255;0;0;76;134;134p\E8\E[J, smcup=\E[76p,
+ use=guru+unk,
+guru-76-w|guru 76 lines by 178 cols,
+ cols#178, lines#76,
+ is2=\E7\E[255;0;0;76;178;178p\E8\E[J, smcup=\E[76p,
+ use=guru+unk,
+guru-76-w-s|ann arbor guru/76 lines+status+wide,
+ cols#178, lines#75,
+ is2=\r\n\E[A\E7\E[255;1;0;76;178;178p\E8\E[J,
+ smcup=\E[76;1p\E[255;1H\E[K, use=guru+s, use=guru+unk,
+guru-76-wm|guru 76 lines by 178 cols with 255 cols memory,
+ cols#178, lines#76,
+ is2=\E7\E[255;0;0;76;178;255p\E8\E[J, smcup=\E[76p,
+ use=guru+unk,
+aaa-rv-unk|ann arbor unknown type,
+ lh#0, lw#0, nlab#0,
+ blink=\E[5;7m, bold=\E[1;7m, home=\E[H, invis=\E[7;8m,
+ is1=\E[7m\E7\E[H\E9\E8, rev=\E[m, rmso=\E[7m, rmul=\E[7m,
+ rs1=\E[H\E[7m\E[J,
+ sgr=\E[%?%p6%t1;%;%?%p2%t4;%;%?%p3%t7;%;%?%p4%t5;%;%?%p1%!%t7;%;%?%p7%t8;%;m,
+ sgr0=\E[7m, smso=\E[m, smul=\E[4;7m,
+
+#### Applied Digital Data Systems (adds)
+#
+# ADDS itself is long gone. ADDS was bought by NCR, and the same group made
+# ADDS and NCR terminals. When AT&T and NCR merged, the engineering for
+# terminals was merged again. Then AT&T sold the terminal business to
+# SunRiver, which later changed its name to Boundless Technologies. The
+# engineers from Teletype, AT&T terminals, ADDS, and NCR (who are still there
+# as of early 1995) are at:
+#
+# Boundless Technologies
+# 100 Marcus Boulevard
+# Hauppauge, NY 11788-3762
+# Vox: (800)-231-5445
+# Fax: (516)-342-7378
+# Web: http://boundless.com
+#
+# Their voice mail used to describe the place as "SunRiver (formerly ADDS)".
+# In 1995 Boundless acquired DEC's terminals business.
+#
+
+# Regent: lowest common denominator, works on all regents.
+# (regent: renamed ":bc:" to ":le:" -- esr)
+regent|Adds Regent Series,
+ OTbs, am,
+ cols#80, lines#24,
+ bel=^G, clear=^L, cr=^M, cub1=^U, cud1=^J, cuf1=^F, cuu1=^Z,
+ home=\EY\s\s, ind=^J, ll=^A,
+# Regent 100 has a bug where if computer sends escape when user is holding
+# down shift key it gets confused, so we avoid escape.
+regent100|Adds Regent 100,
+ xmc#1,
+ bel=^G,
+ cup=\013%p1%' '%+%c\020%p2%{10}%/%{16}%*%p2%{10}%m%+%c,
+ kf0=^B1\r, kf1=^B2\r, kf2=^B3\r, kf3=^B4\r, kf4=^B5\r,
+ kf5=^B6\r, kf6=^B7\r, kf7=^B8\r, lf0=F1, lf1=F2, lf2=F3,
+ lf3=F4, lf4=F5, lf5=F6, lf6=F7, lf7=F8, rmso=\E0@, rmul=\E0@,
+ sgr0=\E0@, smso=\E0P, smul=\E0`, use=regent,
+regent20|Adds Regent 20,
+ bel=^G, cup=\EY%p1%{32}%+%c%p2%{32}%+%c, ed=\Ek, el=\EK,
+ use=regent,
+regent25|Adds Regent 25,
+ bel=^G, kcub1=^U, kcud1=^J, kcuf1=^F, kcuu1=^Z, khome=^A,
+ use=regent20,
+regent40|Adds Regent 40,
+ xmc#1,
+ bel=^G, dl1=\El$<2*>, il1=\EM$<2*>, kf0=^B1\r, kf1=^B2\r,
+ kf2=^B3\r, kf3=^B4\r, kf4=^B5\r, kf5=^B6\r, kf6=^B7\r,
+ kf7=^B8\r, lf0=F1, lf1=F2, lf2=F3, lf3=F4, lf4=F5, lf5=F6,
+ lf6=F7, lf7=F8, rmso=\E0@, rmul=\E0@, sgr0=\E0@, smso=\E0P,
+ smul=\E0`, use=regent25,
+regent40+|Adds Regent 40+,
+ is2=\EB, use=regent40,
+regent60|regent200|Adds Regent 60,
+ dch1=\EE, is2=\EV\EB, kdch1=\EE, kich1=\EF, krmir=\EF,
+ rmir=\EF, rmso=\ER\E0@\EV, smir=\EF, smso=\ER\E0P\EV,
+ use=regent40+,
+# From: <edward@onyx.berkeley.edu> Thu Jul 9 09:27:33 1981
+# (viewpoint: added <kcuf1>, function key, and <dl1> capabilities -- esr)
+viewpoint|addsviewpoint|adds viewpoint,
+ OTbs, am,
+ cols#80, lines#24,
+ bel=^G, clear=^L, cnorm=\017\E0`, cr=^M, cub1=^H, cud1=^J,
+ cuf1=^F, cup=\EY%p1%{32}%+%c%p2%{32}%+%c, cuu1=^Z,
+ cvvis=\017\E0P, dl1=\El, ed=\Ek$<16.1*>, el=\EK$<16>,
+ ind=^J, is2=\017\E0`, kcub1=^U, kcud1=^J, kcuf1=^F, kcuu1=^Z,
+ kf0=^B1, kf2=^B2, kf3=^B!, kf4=^B", kf5=^B#, khome=^A, ll=^A,
+ rmso=^O, rmul=^O, sgr0=^O, smso=^N, smul=^N,
+# Some viewpoints have bad ROMs that foo up on ^O
+screwpoint|adds viewpoint with ^O bug,
+ cvvis@, rmso@, rmul@, smso@, smul@, use=viewpoint,
+
+# From: Jay S. Rouman <jsr@dexter.mi.org> 5 Jul 92
+# The <civis>/<cnorm>/<sgr>/<sgr0> strings were added by ESR from specs.
+# Theory; the vp3a+ wants \E0%c to set highlights, where normal=01000000,
+# underline=01100000, rev=01010000, blink=01000010,dim=01000001,
+# invis=01000100 and %c is the logical or of desired attributes.
+# There is also a `tag bit' enabling attributes, set by \E) and unset by \E(.
+#
+# Update by TD - 2004:
+# Adapted from
+# http://www.cs.utk.edu/~shuford/terminal/adds_viewpoint_news.txt
+#
+# COMMANDS ASCII CODE
+#
+# Address, Absolute ESC,=,row,column
+# Beep BEL
+# Aux Port Enable ESC,@
+# Aux Port Disable ESC,A
+# Backspace BS
+# Cursor back BS
+# Cursor down LF
+# Cursor forward FF
+# Cursor home RS
+# Cursor up VT
+# Cursor supress ETB
+# Cursor enable CAN
+# Erase to end of line ESC,T
+# Erase to end of page ESC,Y
+# Erase screen SUB
+# Keyboard lock SI
+# Keyboard unlock SO
+# Read current cursor position ESC,?
+# Set Attribute ESC,0,x (see below for values of x)
+# Tag bit reset ESC,(
+# Tag bit set ESC,)
+# Transparent Print on ESC,3
+# Transparent Print off ESC,4
+#
+#
+# ATTRIBUTES
+#
+# Normal @ 0100
+# Half Intensity A 0101
+# Blinking B 0102
+# Half Intensity Blinking C 0103
+# Reverse Video P 0120
+# Reverse Video Half Intensity Q 0121
+# Reverse Video Blinking R 0122
+# Reverse Video Half Intensity
+# Blinking S 0123
+# Underlined ` 0140
+# Underlined Half Intensity a 0141
+# Underlined Blinking b 0142
+# Underlined Half Intensity
+# Blinking c 0143
+# Video suppress D 0104
+vp3a+|viewpoint3a+|adds viewpoint 3a+,
+ am, bw,
+ cols#80, it#8, lines#24,
+ blink=\E0B\E), civis=^W, clear=\E*$<80>, cnorm=^X, cr=^M,
+ cub1=^H, cud1=^J, cuf1=^L,
+ cup=\E=%p1%{32}%+%c%p2%{32}%+%c, cuu1=^K, dim=\E0A\E),
+ ed=\EY$<80>, el=\ET, home=^^, ht=^I, ind=^J, invis=\E0D\E),
+ kbs=^H, kcub1=^H, kcud1=^J, kcuf1=^L, kcuu1=^K, khome=^^,
+ nel=^M^J, rev=\E0P\E), rmso=\E(,
+ sgr=%?%p1%p2%|%p3%|%p4%|%p5%|%p7%|%t\E0%{64}%?%p1%t%{17}%|%;%?%p2%t%{32}%|%;%?%p3%t%{16}%|%;%?%p4%t%{2}%|%;%?%p5%t%{1}%|%;%c%?%p7%tD%;\E)%e\E(%;,
+ sgr0=\E(, smso=\E0Q\E), smul=\E0`\E),
+vp60|viewpoint60|addsvp60|adds viewpoint60,
+ use=regent40,
+#
+# adds viewpoint 90 - from cornell
+# Note: emacs sends ei occasionally to insure the terminal is out of
+# insert mode. This unfortunately puts the viewpoint90 IN insert
+# mode. A hack to get around this is <ich1=\EF\s\EF^U>. (Also,
+# - :ei=:im=: must be present in the termcap translation.)
+# - <xhp> indicates glitch that attributes stick to location
+# - <msgr> means it's safe to move in standout mode
+# - <clear=\EG\Ek>: clears screen and visual attributes without affecting
+# the status line
+# Function key and label capabilities merged in from SCO.
+vp90|viewpoint90|adds viewpoint 90,
+ OTbs, bw, msgr, xhp,
+ cols#80, lines#24,
+ clear=\EG\Ek, cub1=^H, cud1=^J, cuf1=^F,
+ cup=\EY%p1%{32}%+%c%p2%{32}%+%c, cuu1=^Z, dch1=\EE,
+ dl1=\El, ed=\Ek, el=\EK, home=\EY\s\s, ht=^I,
+ ich1=\EF \EF\025, ind=^J, kbs=^H, kcub1=^U, kcud1=^J,
+ kcuf1=^F, kcuu1=^Z, kf0=^B1\r, kf1=^B2\r, kf10=^B;\r,
+ kf2=^B3\r, kf3=^B4\r, kf4=^B5\r, kf5=^B6\r, kf6=^B7\r,
+ kf7=^B8\r, kf8=^B9\r, kf9=^B\:\r, khome=^A, lf0=F1, lf1=F2,
+ lf10=F11, lf2=F3, lf3=F4, lf4=F5, lf5=F6, lf6=F7, lf7=F8, lf8=F9,
+ lf9=F10, ll=^A, rmso=\ER\E0@\EV, rmul=\ER\E0@\EV,
+ sgr0=\ER\E0@\EV, smso=\ER\E0Q\EV, smul=\ER\E0`\EV,
+# Note: if return acts weird on a980, check internal switch #2
+# on the top chip on the CONTROL pc board.
+adds980|a980|adds consul 980,
+ OTbs, am,
+ cols#80, lines#24,
+ bel=^G, clear=\014$<1>\013@, cr=^M, cub1=^H, cud1=^J,
+ cuf1=\E^E01, cup=\013%p1%{64}%+%c\E\005%p2%2d,
+ dl1=\E\017$<13>, il1=\E\016$<13>, ind=^J, kf0=\E0, kf1=\E1,
+ kf2=\E2, kf3=\E3, kf4=\E4, kf5=\E5, kf6=\E6, kf7=\E7, kf8=\E8,
+ kf9=\E9, rmso=^O, sgr0=^O, smso=^Y^^^N,
+
+#### C. Itoh Electronics
+#
+# As of 1995 these people no longer make terminals (they're still in the
+# printer business). Their terminals were all clones of the DEC VT series.
+# They're located in Orange County, CA.
+#
+
+# CIT 80 - vt-52 emulator, the termcap has been modified to remove
+# the delay times and do an auto tab set rather than the indirect
+# file used in vt100.
+cit80|cit-80|citoh 80,
+ OTbs, am,
+ cols#80, lines#24,
+ clear=\E[H\EJ, cr=^M, cub1=^H, cud1=\E[B, cuf1=\E[C,
+ cup=\E[%i%p1%2d;%p2%2dH, cuu1=\E[A, ed=\EJ, el=\EK, ff=^L,
+ ind=^J, is2=\E>, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC,
+ kcuu1=\EOA, rmkx=\E[?1l\E>, smkx=\E[?1h\E=,
+# From: Tim Wood <mtxinu!sybase!tim> Fri Sep 27 09:39:12 PDT 1985
+# (cit101: added <rmam>/<smam> based on init string, merged this with c101 -- esr)
+cit101|citc|C.itoh fast vt100,
+ OTbs, am, xenl,
+ cols#80, lines#24,
+ bel=^G, clear=\E[H\E[2J, cnorm=\E[V\E8, cub1=^H, cud1=\E[B,
+ cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH, cuu1=\E[A,
+ cvvis=\E7\E[U, dch1=\E[P, dl1=\E[M, ed=\E[J, el=\E[K,
+ flash=\E[?5h$<200/>\E[?5l, ich1=\E[@, il1=\E[L,
+ is2=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h\E[3g\E[>5g,
+ kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
+ rmam=\E[?7l, rmkx=\E[?1l\E>, rmso=\E[m, rmul=\E[m,
+ sgr0=\E[m, smam=\E[?7h, smkx=\E[?1h\E=, smso=\E[7m,
+ smul=\E[4m,
+# CIE Terminals CIT-101e from Geoff Kuenning <callan!geoff> via BRL
+# The following termcap entry was created from the Callan cd100 entry. The
+# last two lines (with the capabilities in caps) are used by RM-cobol to allow
+# full selection of combinations of reverse video, underline, and blink.
+# (cit101e: removed unknown :f0=\EOp:f1=\EOq:f2=\EOr:f3=\EOs:f4=\EOt:f5=\EOu:\
+# f6=\EOv:f7=\EOw:f8=\EOx:f9=\EOy:AB=\E[0;5m:AL=\E[m:AR=\E[0;7m:AS=\E[0;5;7m:\
+# :NB=\E[0;1;5m:NM=\E[0;1m:NR=\E[0;1;7m:NS=\E[0;1;5;7m: -- esr)
+cit101e|C. Itoh CIT-101e,
+ OTbs, OTpt, am, mir, msgr,
+ cols#80, it#8, lines#24,
+ acsc=, clear=\E[H\E[J, cnorm=, csr=\E[%i%p1%2d;%p2%2dr,
+ cub1=\E[D, cud1=\E[B, cuf1=\E[C, cup=\E[%i%p1%2d;%p2%2dH,
+ cuu1=\E[A, cvvis=\E[?1l\E[?4l\E[?7h, dch1=\E[P, dl1=\E[M,
+ ed=\E[J, el=\E[K, if=/usr/share/tabset/vt100, il1=\E[L,
+ kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kf0=\EOT,
+ kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS, kf5=\EOm, kf6=\EOl,
+ kf7=\EOM, kf8=\EOn, rc=\E8, ri=\EM, rmacs=^O, rmir=\E[4l,
+ rmkx=\E>, rmso=\E[m, rmul=\E[m, sc=\E7, smacs=^N, smir=\E[4h,
+ smkx=\E=, smso=\E[7m, smul=\E[4m,
+# From: David S. Lawyer, June 1997:
+# The CIT 101-e was made in Japan in 1983-4 and imported by CIE
+# Terminals in Irvine, CA. It was part of CITOH Electronics. In the
+# late 1980's CIT Terminals went out of business.
+# There is no need to use the initialization string is=... (by invoking
+# tset or setterm etc.) provided that the terminal has been manually set
+# up (and the setup saved with ^S) to be compatible with this termcap. To be
+# compatible it should be in ANSI mode (not VT52). A set-up that
+# works is to set all the manually setable stuff to factory defaults
+# by pressing ^D in set-up mode. Then increse the brighness with the
+# up-arrow key since the factory default will likely be dim on an old
+# terminal. Then change any options you want (provided that they are
+# compatible with the termcap). For my terminal I set: Screen
+# Background: light; Keyclicks: silent; Auto wraparound: on; CRT saver:
+# on. I also set up mine for parity (but you may not need it). Then
+# save the setup with ^S.
+# (cit101e-rv: added empty <rmcup> to suppress a tic warning. --esr)
+cit101e-rv|Citoh CIT-101e (sets reverse video),
+ am, eo, mir, msgr, xenl, xon,
+ cols#80, it#8, lines#24,
+ OTnl=\EM, bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z,
+ civis=\E[1v, clear=\E[H\E[J, cnorm=\E[0;3;4v, cr=^M,
+ csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
+ cud=\E[%p1%dB, cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
+ cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
+ cvvis=\E[3;5v, dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM,
+ dl1=\E[M, ed=\E[J, el=\E[K, flash=\E[?5l\E[?5h$<200/>,
+ home=\E[H, hpa=\E[%i%p1%dG, ht=^I, hts=\EH, ich=\E[%p1%d@,
+ ich1=\E[@, il=\E[%p1%dL, il1=\E[L, ind=^J, indn=\E[%p1%dS,
+ is2=\E<\E>\E[?1l\E[?3l\E[?4l\E[?5h\E[?7h\E[?8h\E[3g\E[>5g\E(B\E[m\E[20l\E[1;24r\E[24;1H,
+ kbs=\177, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
+ kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS, nel=\EE, rc=\E8,
+ rev=\E[7m, ri=\EM, rin=\E[%p1%dT, rmcup=, rmir=\E[4l,
+ rmso=\E[m, rmul=\E[m, rs1=\Ec\E[?7h\E[>5g, sc=\E7,
+ sgr0=\E[m, smcup=\E[>5g\E[?7h\E[?5h, smir=\E[4h,
+ smso=\E[7m, smul=\E[4m, tbc=\E[3g, u6=\E[%i%p1%d;%p2%dR,
+ u7=\E[6n, u8=\E[?6c, u9=\E[c,
+cit101e-n|CIT-101e w/o am,
+ am@,
+ cvvis=\E[?1l\E[?4l\E[?7l, kbs=^H, kcub1=^H, kcud1=^J,
+ use=cit101e,
+cit101e-132|CIT-101e with 132 cols,
+ cols#132,
+ kbs=^H, kcub1=^H, kcud1=^J, use=cit101e,
+cit101e-n132|CIT-101e with 132 cols w/o am,
+ am@,
+ cols#132,
+ cvvis=\E[?1l\E[?4l\E[?7l, kbs=^H, kcub1=^H, kcud1=^J,
+ use=cit101e,
+# CIE Terminals CIT-500 from BRL
+# The following SET-UP modes are assumed for normal operation:
+# GENERATE_XON/XOFF:YES DUPLEX:FULL NEWLINE:OFF
+# AUTOWRAP:ON MODE:ANSI SCREEN_LENGTH:64_LINES
+# DSPLY_CNTRL_CODES?NO PAGE_WIDTH:80 EDIT_MODE:OFF
+# Other SET-UP modes may be set for operator convenience or communication
+# requirements.
+# Hardware tabs are assumed to be set every 8 columns; they can be set up
+# by the "reset", "tset", or "tabs" utilities. No delays are specified; use
+# "stty ixon -ixany" to enable DC3/DC1 flow control!
+# (cit500: I added <rmam>/<smam> based on the init string -- esr)
+cit500|CIE Terminals CIT-500,
+ OTbs, OTpt, mir, msgr, xon,
+ OTkn#10, cols#80, it#8, lines#64, vt#3,
+ acsc=, bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z,
+ clear=\E[H\E[J, cr=^M, csr=\E[%i%p1%d;%p2%dr,
+ cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=^J,
+ cuf=\E[%p1%dC, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
+ cuu=\E[%p1%dA, cuu1=\EM, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
+ ed=\EJ, el=\EK, home=\E[H, ht=^I, hts=\EH, il=\E[%p1%dL,
+ il1=\E[L, ind=^J, is2=\E<\E)0, kbs=^H, kcbt=\E[Z, kcub1=\EOD,
+ kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA, kdch1=\E[P, kdl1=\E[M,
+ ked=\EJ, kel=\EK, kf0=\EOP, kf1=\EOQ, kf2=\EOR, kf3=\EOS,
+ kf4=\EOU, kf5=\EOV, kf6=\EOW, kf7=\EOX, kf8=\EOY, kf9=\EOZ,
+ khome=\E[H, kich1=\E[4h, kil1=\E[L, krmir=\E[4l, lf0=PF1,
+ lf1=PF2, lf2=PF3, lf3=PF4, lf4=F15, lf5=F16, lf6=F17, lf7=F18,
+ lf8=F19, lf9=F20, ll=\E[64H, nel=\EE, rc=\E8, rev=\E[7m,
+ ri=\EM, rmacs=^O, rmam=\E[?7l, rmir=\E[4l, rmkx=\E[?1l\E>,
+ rmso=\E[m, rmul=\E[m,
+ rs1=\E<\E2\E[20l\E[?6l\E[r\E[m\E[q\E(B\017\E)0\E>,
+ sc=\E7, sgr0=\E[m, smacs=^N, smam=\E[?7h, smir=\E[4h,
+ smkx=\E[?1h\E=, smso=\E[7m, smul=\E[4m, tbc=\E[3g,
+
+# C. Itoh printers begin here
+citoh|ci8510|8510|c.itoh 8510a,
+ cols#80, it#8,
+ bold=\E!, cub1@,
+ is2=\E(009\,017\,025\,033\,041\,049\,057\,065\,073.,
+ rep=\ER%p2%03d%p1%c, ri=\Er, rmul=\EY, sgr0=\E"\EY,
+ smul=\EX, use=lpr,
+citoh-pica|citoh in pica,
+ is1=\EN, use=citoh,
+citoh-elite|citoh in elite,
+ cols#96,
+ is1=\EE,
+ is2=\E(009\,017\,025\,033\,041\,049\,057\,065\,073\,081\,089.,
+ use=citoh,
+citoh-comp|citoh in compressed,
+ cols#136,
+ is1=\EQ,
+ is2=\E(009\,017\,025\,033\,041\,049\,057\,065\,073\,081\,089\,097\,105\,113\,121\,129.,
+ use=citoh,
+# citoh has infinite cols because we don't want lp ever inserting \n\t**.
+citoh-prop|citoh-ps|ips|citoh in proportional spacing mode,
+ cols#32767,
+ is1=\EP, use=citoh,
+citoh-6lpi|citoh in 6 lines per inch mode,
+ is3=\EA, use=citoh,
+citoh-8lpi|citoh in 8 lines per inch mode,
+ lines#88,
+ is3=\EB, use=citoh,
+
+#### Control Data (cdc)
+#
+
+cdc456|cdc 456 terminal,
+ OTbs, am,
+ cols#80, lines#24,
+ bel=^G, clear=^Y^X, cr=^M, cub1=^H, cud1=^J, cuf1=^L,
+ cup=\E1%p1%{32}%+%c%p2%{32}%+%c, cuu1=^Z, dl1=\EJ, ed=^X,
+ el=^V, home=^Y, il1=\EL, ind=^J,
+
+# Assorted CDC terminals from BRL (improvements by DAG & Ferd Brundick)
+cdc721|CDC Viking,
+ OTbs, am,
+ cols#80, lines#24,
+ clear=^L, cuf1=^X, cup=\002%p2%{32}%+%c%p1%{32}%+%c,
+ cuu1=^W, el=^K, home=^Y, kcub1=^H, kcud1=^J, kcuf1=^I,
+ kcuu1=^W, khome=^Y,
+cdc721ll|CDC Vikingll,
+ OTbs, am,
+ cols#132, lines#24,
+ clear=^L, cuf1=^X, cup=\002%p2%{32}%+%c%p1%{32}%+%c,
+ cuu1=^W, el=^K, home=^Y, kcub1=^H, kcud1=^J, kcuf1=^I,
+ kcuu1=^W, khome=^Y,
+# (cdc752: the BRL entry had :ll=\E1 ^Z: commented out
+cdc752|CDC 752,
+ OTbs, am, bw, xhp,
+ cols#80, lines#24,
+ bel=^G, clear=\030\E1\s\s, cr=^M, cub1=^H, cud1=^J, cuf1=^U,
+ cup=\E1%p2%{32}%+%c%p1%{32}%+%c, cuu1=^Z, el=^V,
+ home=\E1\s\s, ind=^J, ll=^Y, rs1=\E1 \030\002\003\017,
+# CDC 756
+# The following switch/key settings are assumed for normal operation:
+# 96 chars SCROLL FULL duplex not BLOCK
+# Other switches may be set according to communication requirements.
+# Insert/delete-character cannot be used, as the whole display is affected.
+# "so" & "se" are commented out until jove handles "sg" correctly.
+cdc756|CDC 756,
+ OTbs, am, bw,
+ OTkn#10, cols#80, lines#24,
+ bel=^G, clear=^Y^X, cr=^M, cub1=^H, cud1=^J, cuf1=^U,
+ cup=\E1%p2%{32}%+%c%p1%{32}%+%c, cuu1=^Z,
+ dl1=\EJ$<6*/>, ed=^X, el=^V, home=^Y, il1=\EL$<6*/>, ind=^J,
+ kbs=^H, kcub1=^H, kcud1=^J, kcuf1=^U, kcuu1=^Z, kdch1=\EI,
+ kdl1=\EL, ked=^X, kel=^V, kf0=\EA, kf1=\EB, kf2=\EC, kf3=\ED,
+ kf4=\EE, kf5=\EF, kf6=\EG, kf7=\EH, kf8=\Ea, kf9=\Eb, khome=^Y,
+ khts=^O, kich1=\EK, kil1=\EL, lf0=F1, lf1=F2, lf2=F3, lf3=F4,
+ lf4=F5, lf5=F6, lf6=F7, lf7=F8, lf8=F9, lf9=F10, ll=^Y^Z,
+ rs1=\031\030\002\003\017,
+#
+# CDC 721 from Robert Viduya, Ga. Tech. <ihnp4!gatech!gitpyr!robert> via BRL.
+#
+# Part of the long initialization string defines the "DOWN" key to the left
+# of the tab key to send an ESC. The real ESC key is positioned way out
+# in right field.
+#
+# The termcap won't work in 132 column mode due to the way it it moves the
+# cursor. Termcap doesn't have the capability (as far as I could tell) to
+# handle the 721 in 132 column mode.
+#
+# (cdc721: changed :ri: to :sr: -- esr)
+cdc721-esc|Control Data 721,
+ OTbs, OTpt, am, bw, msgr, xon,
+ OTkn#10, cols#80, it#8, lines#30,
+ bel=^G, blink=^N, cbt=^^^K, clear=^L, cub1=^H, cud1=^Z,
+ cuf1=^X, cup=\002%p2%{32}%+%c%p1%{32}%+%c, cuu1=^W,
+ dch1=^^N, dim=^\, dl1=^^Q, ed=^^P, el=^K, home=^Y, hts=^^^RW,
+ ich1=^^O, il1=^^R, ind=\036W =\036U, invis=^^^R[,
+ is2=\036\022B\003\036\035\017\022\025\035\036E\036\022H\036\022J\036\022L\036\022N\036\022P\036\022Q\036\022\036\022\^\036\022b\036\022i\036W =\036\022Z\036\011C1-` `!k/o,
+ kbs=^H, kcub1=^H, kcud1=^Z, kcuf1=^X, kcuu1=^W, kf0=^^q,
+ kf1=^^r, kf2=^^s, kf3=^^t, kf4=^^u, kf5=^^v, kf6=^^w, kf7=^^x,
+ kf8=^^y, kf9=^^z, khome=^Y, ll=^B =, rev=^^D,
+ ri=\036W =\036V, rmir=, rmkx=^^^Rl, rmso=^^E, rmul=^],
+ sgr0=\017\025\035\036E\036\022\\, smir=, smkx=^^^Rk,
+ smso=^^D, smul=^\, tbc=^^^RY,
+
+#### Getronics
+#
+# Getronics is a Dutch electronics company that at one time was called
+# `Geveke' and made async terminals; but (according to the company itself!)
+# they've lost all their documentation on the command set. The hardware
+# documentation suggests the terminals were actually manufactured by a
+# Taiwanese electronics company named Cal-Comp. There are known
+# to have been at least two models, the 33 and the 50.
+#
+
+# The 50 seems to be a top end vt220 clone, with the addition of a higher
+# screen resolution, a larger screen, at least 1 page of memory above and
+# below the screen, apparently pages of memory right and left of the screen
+# which can be panned, and about 75 function keys (15 function keys x normal,
+# shift, control, func A, func B). It also has more setup possibilities than
+# the vt220. The monitor case is dated November 1978 and the keyboard case is
+# May 1982.
+#
+# The vt100 emulation works as is. The entry below describes the rather
+# non-conformant (but more featureful) ANSI mode.
+#
+# From: Stephen Peterson <stv@utrecht.ow.nl>, 27 May 1995
+visa50|geveke visa 50 terminal in ansi 80 character mode,
+ bw, mir, msgr,
+ cols#80, lines#25,
+ acsc=0_aaffggh jjkkllmmnnooqqssttuuvvwwxx, bel=^G,
+ blink=\E[5m, bold=\E[1m, cbt=\E[Z, clear=\E[H\E[2J, cr=^M,
+ csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=\E[D,
+ cud=\E[%p1%dB, cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
+ cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
+ dch=\E[%p1%dX, dch1=\E[X, dim=\E[2m, dl=\E[%p1%dM,
+ dl1=\E[M, ed=\E[J, el=\E[K, flash=\E[?5h\E[?5l, home=\E[H,
+ hpa=\E[%i%p1%dG, ht=^I, ich=\E[%p1%d@, ich1=\E[@,
+ il=\E[%p1%dL, il1=\E[L, ind=^J, invis=\E[8m,
+ is2=\E0;2m\E[1;25r\E[25;1H\E[?3l\E[?7h\E[?8h,
+ ka1=\E[f, ka3=\EOQ, kb2=\EOP, kbs=^H, kc1=\EOR, kc3=\EOS,
+ kcub1=\E[D, kcud1=\E[A, kcuf1=\E[C, kcuu1=\E[A, kdch1=\177,
+ kdl1=\EOS, kf0=\E010, kf1=\E001, kf10=\E011, kf2=\E002,
+ kf3=\E003, kf4=\E004, kf5=\E005, kf6=\E006, kf7=\E007,
+ kf8=\E008, kf9=\E009, khome=\E[f, lf2=A delete char,
+ lf3=A insert line, lf4=A delete line, lf5=A clear,
+ lf6=A ce of/cf gn, lf7=A print, lf8=A on-line,
+ lf9=A funcl0=A send, nel=^M^J, rev=\E[7m, rmacs=\E[3l,
+ rmam=\E[?7l, rmir=\E[4l, rmkx=\E>, rmso=\E[0;2m,
+ rmul=\E[0m, sgr0=\E[0;2m, smacs=\E3h, smam=\E?7h,
+ smir=\E[4h, smkx=\E=, smso=\E[2;7m, smul=\E[4m, tbc=\E[3g,
+ vpa=\E[%i%p1%dd,
+
+#### Human Designed Systems (Concept)
+#
+# Human Designed Systems
+# 400 Fehley Drive
+# King of Prussia, PA 19406
+# Vox: (610)-277-8300
+# Fax: (610)-275-5739
+# Net: support@hds.com
+#
+# John Martin <john@hds.com> is their termcap expert. They're mostly out of
+# the character-terminal business now (1995) and making X terminals. In
+# particular, the whole `Concept' line described here was discontinued long
+# ago.
+#
+
+# From: <vax135!hpk> Sat Jun 27 07:41:20 1981
+# Extensive changes to c108 by arpavax:eric Feb 1982
+# Some unknown person at SCO then translated it to terminfo.
+#
+# There seem to be a number of different versions of the C108 PROMS
+# (with bug fixes in its Z-80 program).
+#
+# The first one that we had would lock out the keyboard of you
+# sent lots of short lines (like /usr/dict/words) at 9600 baud.
+# Try that on your C108 and see if it sends a ^S when you type it.
+# If so, you have an old version of the PROMs.
+#
+# You should configure the C108 to send ^S/^Q before running this.
+# It is much faster (at 9600 baud) than the c100 because the delays
+# are not fixed.
+# new status line display entries for c108-8p:
+# <is3> - init str #3 - setup term for status display -
+# set programmer mode, select window 2, define window at last
+# line of memory, set bkgnd stat mesg there, select window 0.
+#
+# <tsl> - to status line - select window 2, home cursor, erase to
+# end-of-window, 1/2 bright on, goto(line#0, col#?)
+#
+# <fsl> - from status line - 1/2 bright off, select window 0
+#
+# <dsl> - disable status display - set bkgnd status mesg with
+# illegal window #
+#
+# There are probably more function keys that should be added but
+# I don't know what they are.
+#
+# No delays needed on c108 because of ^S/^Q handshaking
+#
+c108|concept108|c108-8p|concept108-8p|concept 108 w/8 pages,
+ is3=\EU\E z"\Ev\001\177 !p\E ;"\E z \Ev \001\177p\Ep\n,
+ rmcup=\Ev \001\177p\Ep\r\n, use=c108-4p,
+c108-4p|concept108-4p|concept 108 w/4 pages,
+ OTbs, eslok, hs, xon,
+ pb@,
+ acsc=jEkTl\\mMqLxU, cnorm=\Ew, cr=^M,
+ cup=\Ea%p1%?%p1%{95}%>%t\001%{96}%-%;%{32}%+%c%p2%?%p2%{95}%>%t\001%{96}%-%;%{32}%+%c,
+ cvvis=\EW, dch1=\E 1$<16*>, dsl=\E ;\177, fsl=\Ee\E z\s,
+ ind=^J, is1=\EK\E!\E F,
+ is3=\EU\E z"\Ev\177 !p\E ;"\E z \Ev \001 p\Ep\n,
+ rmacs=\Ej\s, rmcup=\Ev \001 p\Ep\r\n, smacs=\Ej!,
+ smcup=\EU\Ev 8p\Ep\r\E\025,
+ tsl=\E z"\E?\E\005\EE\Ea %+\s, use=c100,
+c108-rv|c108-rv-8p|concept 108 w/8 pages in reverse video,
+ rmcup=\Ev \002 p\Ep\r\n, smcup=\EU\Ev 8p\Ep\r,
+ use=c108-rv-4p,
+c108-rv-4p|concept108rv4p|concept 108 w/4 pages in reverse video,
+ flash=\EK$<200>\Ek, is1=\Ek, rmso=\Ee, smso=\EE,
+ use=c108-4p,
+c108-w|c108-w-8p|concept108-w-8|concept108-w8p|concept 108 w/8 pages in wide mode,
+ cols#132,
+ is1=\E F\E", rmcup=\Ev ^A0\001D\Ep\r\n,
+ smcup=\EU\Ev 8\001D\Ep\r, use=c108-8p,
+
+# Concept 100:
+# These have only window relative cursor addressing, not screen
+# relative. To get it to work right here, smcup/rmcup (which
+# were invented for the concept) lock you into a one page
+# window for screen style programs.
+#
+# To get out of the one page window, we use a clever trick:
+# we set the window size to zero ("\Ev " in rmcup) which the
+# terminal recognizes as an error and resets the window to all
+# of memory.
+#
+# This trick works on c100 but does not on c108, sigh.
+#
+# Some tty drivers use cr3 for concept, others use nl3, hence
+# the delays on cr and ind below. This padding is only needed at
+# 9600 baud and up. One or the other is commented out depending on
+# local conventions.
+#
+# 2 ms padding on <rmcup> isn't always enough. 6 works fine. Maybe
+# less than 6 but more than 2 will work.
+#
+# Note: can't use function keys f7-f10 because they are
+# indistinguishable from arrow keys (!), also, del char and
+# clear eol use xon/xoff so they probably won't work very well.
+#
+# Also note that we don't define insrt/del char/delline/eop/send
+# because they don't transmit unless we reset them - I figured
+# it was a bad idea to clobber their definitions.
+#
+# The <mc5> sequence changes the escape character to ^^ so that
+# escapes will be passed through to the printer. Only trouble
+# is that ^^ won't be - ^^ was chosen to be unlikely.
+# Unfortunately, if you're sending raster bits through to be
+# plotted, any character you choose will be likely, so we lose.
+#
+# \EQ"\EY(^W (send anything from printer to host, for xon/xoff)
+# cannot be # in is2 because it will hang a c100 with no printer
+# if sent twice.
+c100|concept100|concept|c104|c100-4p|hds concept 100,
+ OTbs, am, eo, mir, ul, xenl,
+ cols#80, lines#24, pb#9600, vt#8,
+ bel=^G, blink=\EC, clear=\E?\E\005$<2*>, cr=$<9>\r,
+ cub1=^H, cud1=^J, cuf1=\E=,
+ cup=\Ea%p1%{32}%+%c%p2%{32}%+%c, cuu1=\E;,
+ dch1=\E\021$<16*>, dim=\EE, dl1=\E\002$<3*>,
+ ed=\E\005$<16*>, el=\E\025$<16>, flash=\Ek$<200>\EK,
+ ht=\011$<8>, il1=\E\022$<3*>, ind=^J, invis=\EH, ip=$<16*>,
+ is1=\EK,
+ is2=\EU\Ef\E7\E5\E8\El\ENH\E\0\Eo&\0\Eo'\E\Eo!\0\E\007!\E\010A@ \E4#\:"\E\:a\E4#;"\E\:b\E4#<"\E\:c,
+ is3=\Ev $<6>\Ep\n, kbs=^H, kcbt=\E', kctab=\E_,
+ kcub1=\E>, kcud1=\E<, kcuf1=\E=, kcuu1=\E;, kdch1=\E^Q,
+ kdl1=\E^B, ked=\E^C, kel=\E^S, kf1=\E5, kf2=\E6, kf3=\E7,
+ kf4=\E8, kf5=\E9, kf6=\E\:a, kf7=\E\:b, kf8=\E\:c, khome=\E?,
+ khts=\E], kich1=\E^P, kil1=\E^R, kind=\E[, knp=\E-, kpp=\E.,
+ kri=\E\\, krmir=\E\0, mc4=\036o \E\EQ!\EYP\027,
+ mc5=\EQ"\EY(\027\EYD\Eo \036, prot=\EI,
+ rep=\Er%p1%c%p2%{32}%+%c$<.2*>, rev=\ED,
+ rmcup=\Ev $<6>\Ep\r\n, rmir=\E\s\s, rmkx=\Ex,
+ rmso=\Ed, rmul=\Eg, sgr0=\EN@,
+ smcup=\EU\Ev 8p\Ep\r\E\025$<16>, smir=\E^P, smkx=\EX,
+ smso=\ED, smul=\EG,
+c100-rv|c100-rv-4p|concept100-rv|c100 rev video,
+ cnorm@, cvvis@, flash=\EK$<200>\Ek, is1=\Ek, rmso=\Ee,
+ smso=\EE, use=c100,
+oc100|oconcept|c100-1p|old 1 page concept 100,
+ in,
+ is3@, use=c100,
+
+# From: Walter Skorski <walt@genetics1.JMP.TJU.EDU>, 16-oct-1996.
+# Lots of notes, originally inline, but ncurses doesn't grok that.
+#
+# am: not available in power on mode, but turned on with \E[=107;207h in
+# is2=. Also, \E=124l in is2= could have been used to prevent needing
+# to specify xenl:, but that would have rendered the last space on the
+# last line useless.
+# bw: Not available in power on mode, but turned on with \E[=107;207h in
+# is2=.
+# clear: Could be done with \E[2J alone, except that vi (and probably most
+# other programs) assume that this also homes the cursor.
+# dsl: Go to window 2, go to the beginning of the line, use a line feed to
+# scroll the window, and go back to window 1.
+# is2: the string may cause a warning to be issued by tic that it
+# found a very long line and that it suspects that a comma is missing
+# somewhere. This warning can be ignored (unless it comes up more than
+# once). The initialization string contains the following commands:
+#
+# [Setup mode items changed from factory defaults:]
+# \E)0 set alternate character set to
+# graphics
+# ^O set character set to default
+# [In case it wasn't]
+# \E[m turn off all attributes
+# [In case they weren't off]
+# \E[=107; cursor wrap and
+# 207h character wrap on
+# \E[90;3u set Fkey definitions to "transmit"
+# defaults
+# \E[92;3u set cursor key definitions to
+# "transmit" defaults
+# \E[43;1u set shift F13 to transmit...
+# \177\E$P\177
+# \E[44;1u set shift F14 to transmit...
+# \177\E$Q\177
+# \E[45;1u set shift F15 to transmit...
+# \177\E$R\177
+# \E[46;1u set shift F16 to transmit...
+# \177\E$S\177
+# \E[200;1u set shift up to transmit...
+# \177\E$A\177
+# \E[201;1u set shift down to transmit...
+# \177\E$B\177
+# \E[202;1u set shift right to transmit...
+# \177\E$C\177
+# \E[203;1u set shift left to transmit...
+# \177\E$D\177
+# \E[204;1u set shift home to transmit...
+# \177\E$H\177
+# \E[212;1u set backtab to transmit...
+# \177\E$I\177
+# \E[213;1u set shift backspace to transmit...
+# \177\E$^H\177
+# \E[214;1u set shift del to transmit...
+# "\E$\177"
+# [Necessary items not mentioned in setup mode:]
+# \E[2!w move to window 2
+# \E[25;25w define window as line 25 of memory
+# \E[!w move to window 1
+# \E[2*w show current line of window 2 as
+# status line
+# \E[2+x set meta key to use high bit
+# \E[;3+} move underline to bottom of character
+#
+# All Fkeys are set to their default transmit definitions with \E[90;3u
+# in is2=. IMPORTANT: to use this terminal definition, the "quit" stty
+# setting MUST be redefined or deactivated, because the default is
+# contained in almost all of this terminal's Fkey strings! If for some
+# reason "quit" cannot be altered, the Fkeys can, but it would be
+# necessary to change ^| to ^] in all of these definitions, and add
+# \E[2;029!t to is2.
+# lines: is set to 24 because this terminal refuses to treat the 25th
+# line normally.
+# ll: Not available in power on mode, but turned on with \E[=107;207h in
+# is2=.
+# lm: Pointless, given that this definition locks a single screen of
+# memory into view, but what the hey...
+# rmso: Could use \E[1;7!{ to turn off only bold and reverse (leaving any
+# other attributes alone), but some programs expect this to turn off
+# everything.
+# rmul: Could use \E[4!{ to turn off only underline (leaving any other
+# attributes alone), but some programs expect this to turn off
+# everything.
+# sgr: Attributes are set on this terminal with the string \E[ followed by
+# a list of attribute code numbers (in decimal, separated by
+# semicolons), followed by the character m. The attribute code
+# numbers are:
+# 1 for bold;
+# 2 for dim (which is ignored in power on mode);
+# 4 for underline;
+# 5 for blinking;
+# 7 for inverse;
+# 8 for not displayable; and
+# =99 for protected (except that there are strange side
+# effects to protected characters which make them inadvisable).
+# The mapping of terminfo parameters to attributes is as follows:
+# %p1 (standout) = bold and inverse together;
+# %p2 (underline) = underline;
+# %p3 (reverse) = inverse;
+# %p4 (blink) = blinking;
+# %p5 (dim) is ignored;
+# %p6 (bold) = bold;
+# %p7 (invisible) = not displayable;
+# %p8 (protected) is ignored; and
+# %p9 (alt char set) = alt char set.
+# The code to do this is:
+# \E[0 OUTPUT \E[0
+# %?%p1%p6%O IF (standout; bold) OR
+# %t;1 THEN OUTPUT ;1
+# %; ENDIF
+# %?%p2 IF underline
+# %t;4 THEN OUTPUT ;4
+# %; ENDIF
+# %?%p4 IF blink
+# %t;5 THEN OUTPUT ;5
+# %; ENDIF
+# %?%p1%p3%O IF (standout; reverse) OR
+# %t;7 THEN OUTPUT ;7
+# %; ENDIF
+# %?%p7 IF invisible
+# %t;8 THEN OUTPUT ;8
+# %; ENDIF
+# m OUTPUT m
+# %?%p9 IF altcharset
+# %t^N THEN OUTPUT ^N
+# %e^O ELSE OUTPUT ^O
+# %; ENDIF
+# sgr0: Everything is turned off (including alternate character set), since
+# there is no way of knowing what it is that the program wants turned
+# off.
+# smul: The "underline" attribute is reconfigurable to an overline or
+# strikethru, or (as done with \E[;3+} in is2=), to a line at the true
+# bottom of the character cell. This was done to allow for more readable
+# underlined characters, and to be able to distinguish between an
+# underlined space, an underscore, and an underlined underscore.
+# xenl: Terminal can be configured to not need this, but this "glitch"
+# behavior is actually preferable with autowrap terminals.