def_prog_mode, def_shell_mode, reset_prog_mode,
reset_shell_mode, resetty, savetty, getsyx, setsyx, ripof-
fline, curs_set, napms - low-level xscurses routines
void getsyx(int y, int x);
void setsyx(int y, int x);
int ripoffline(int line, int (*init)(WINDOW *, int));
int curs_set(int visibility);
int napms(int ms);
The following routines give low-level access to various
curses capabilities. Theses routines typically are used
inside library routines.
The def_prog_mode and def_shell_mode routines save the
current terminal modes as the "program" (in curses) or
"shell" (not in curses) state for use by the
reset_prog_mode and reset_shell_mode routines. This is
done automatically by initscr. There is one such save
area for each screen context allocated by newterm().
The reset_prog_mode and reset_shell_mode routines restore
the terminal to "program" (in curses) or "shell" (out of
curses) state. These are done automatically by endwin
and, after an endwin, by doupdate, so they normally are
The resetty and savetty routines save and restore the
state of the terminal modes. savetty saves the current
state in a buffer and resetty restores the state to what
it was at the last call to savetty.
The getsyx routine returns the current coordinates of the
virtual screen cursor in y and x. If leaveok is currently
TRUE, then -1,-1 is returned. If lines have been removed
from the top of the screen, using ripoffline, y and x
include these lines; therefore, y and x should be used
only as arguments for setsyx.
The setsyx routine sets the virtual screen cursor to y, x.
If y and x are both -1, then leaveok is set. The two rou-
tines getsyx and setsyx are designed to be used by a
cursor. The library routine would call getsyx at the
beginning, do its manipulation of its own windows, do a
wnoutrefresh on its windows, call setsyx, and then call
The ripoffline routine provides access to the same facil-
ity that slk_init [see curs_slk(3X)] uses to reduce the
size of the screen. ripoffline must be called before
initscr or newterm is called. If line is positive, a line
is removed from the top of stdscr; if line is negative, a
line is removed from the bottom. When this is done inside
initscr, the routine init (supplied by the user) is called
with two arguments: a window pointer to the one-line win-
dow that has been allocated and an integer with the number
of columns in the window. Inside this initialization rou-
tine, the integer variables LINES and COLS (defined in
<curses.h>) are not guaranteed to be accurate and wrefresh
or doupdate must not be called. It is allowable to call
wnoutrefresh during the initialization routine.
ripoffline can be called up to five times before calling
initscr or newterm.
The curs_set routine sets the cursor state is set to
invisible, normal, or very visible for visibility equal to
0, 1, or 2 respectively. If the terminal supports the
visibility requested, the previous cursor state is
returned; otherwise, ERR is returned.
The napms routine is used to sleep for ms milliseconds.
Except for curs_set, these routines always return OK.
curs_set returns the previous cursor state, or ERR if the
requested visibility is not supported.
Note that getsyx is a macro, so & is not necessary before
the variables y and x.
The SVr4 man pages warn that the return value of curs_set
"is currently incorrect". This implementation gets it
right, but it may be unwise to count on the correctness of
the return value anywhere else.
The functions setsyx and getsyx are not described in the
XSI Curses standard, Issue 4. All other functions are as
described in XSI Curses.
The SVr4 documentation describes setsyx and getsyx as hav-
ing return type int. This is misleading, as they are
curses(3X), curs_initscr(3X), curs_outopts(3X),
curs_refresh(3X), curs_scr_dump(3X), curs_slk(3X)