./doc/html/man/new_pair.3x.html
./doc/html/man/panel.3x.html
./doc/html/man/resizeterm.3x.html
+./doc/html/man/scr_dump.5.html
./doc/html/man/tabs.1.html
./doc/html/man/term.5.html
./doc/html/man/term.7.html
./man/new_pair.3x
./man/panel.3x
./man/resizeterm.3x
+./man/scr_dump.5
./man/tabs.1
./man/term.5
./man/term.7
-- sale, use or other dealings in this Software without prior written --
-- authorization. --
-------------------------------------------------------------------------------
--- $Id: NEWS,v 1.2806 2017/04/15 18:00:38 tom Exp $
+-- $Id: NEWS,v 1.2822 2017/04/22 20:29:13 tom Exp $
-------------------------------------------------------------------------------
This is a log of changes that ncurses has gone through since Zeyd started
Changes through 1.9.9e did not credit all contributions;
it is not possible to add this information.
+20170422
+ + build-fix for termcap-configuration (report by Chi-Hsuan Yen).
+ + improve terminfo manual page discussion of control- and graphics-
+ characters.
+ + remove tic warning about "^?" in string capabilities, which was
+ marked as an extension (cf: 20000610, 20110820); however all Unix
+ implementations support this and X/Open Curses does not address it.
+ On the other hand, termcap never did support this feature.
+ + correct missing comma-separator between string capabilities in
+ icl6402 and m2-nam -TD
+ + restore rmir/smir in ansi+idc to better match original ansiterm+idc,
+ add alias ansiterm (report by Robert King).
+ + amend an old check for ambiguous use of "ma" in terminfo versus
+ a termcap use, if the capability is cancelled to treat it as number.
+ + correct a case in _nc_captoinfo() which read "%%" and emitted "%".
+ + modify sscanf calls in _nc_infotocap() for patterns "%{number}%+%c"
+ and "%'char'%+%c" to check that the final character is really 'c',
+ avoiding a case in icl6404 which cannot be converted to termcap.
+ + in _nc_infotocap(), add a check to ensure that terminfo "^?" is not
+ written to termcap, because the BSDs did not implement that.
+ + in _nc_tic_expand() and _nc_infotocap(), improve string-length check
+ when deciding whether to use "^X" or "\xxx" format for control
+ characters, to make the output of tic/infocmp more predictable.
+ + limit termcap "%d" width to 2 digits on input, and use "%2" in
+ preference to "%02" on output.
+ + correct terminfo/termcap conversion of "%02" and "%03" into "%2" and
+ "%3"; the result repeated the last character.
+ + add man/scr_dump.5 to document screen-dump format.
+
20170415
+ modify several test programs to use new popup_msgs, adapted from
help-screen used in test/edit_field.c
-5:0:9 6.0 20170415
+5:0:9 6.0 20170422
# use or other dealings in this Software without prior written #
# authorization. #
##############################################################################
-# $Id: dist.mk,v 1.1156 2017/04/09 10:43:26 tom Exp $
+# $Id: dist.mk,v 1.1157 2017/04/16 10:19:41 tom Exp $
# Makefile for creating ncurses distributions.
#
# This only needs to be used directly as a makefile by developers, but
# These define the major/minor/patch versions of ncurses.
NCURSES_MAJOR = 6
NCURSES_MINOR = 0
-NCURSES_PATCH = 20170415
+NCURSES_PATCH = 20170422
# We don't append the patch to the version, since this only applies to releases
VERSION = $(NCURSES_MAJOR).$(NCURSES_MINOR)
<TABLE ALIGN=CENTER BORDER>
<TR ALIGN=LEFT>
<TH>C name</TH><TH>Ada name</TH><TH>man page</TH></TR>
-<TR><TD>_nc_freeall()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_159">Curses_Free_All</A></TD><TD><A HREF="../man/curs_trace.3x.html">curs_trace.3x</A></TD></TR>
-<TR><TD>_tracef()</TD><TD><A HREF="terminal_interface-curses-trace__ads.htm#AFU_2">Trace_Put</A></TD><TD><A HREF="../man/curs_trace.3x.html">curs_trace.3x</A></TD></TR>
<TR><TD>assume_default_colors()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_156">Assume_Default_Colors</A></TD><TD><A HREF="../man/default_colors.3x.html">default_colors.3x</A></TD></TR>
<TR><TD>baudrate()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_131">Baudrate</A></TD><TD><A HREF="../man/curs_termattrs.3x.html">curs_termattrs.3x</A></TD></TR>
<TR><TD>beep()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_40">Beep</A></TD><TD><A HREF="../man/curs_beep.3x.html">curs_beep.3x</A></TD></TR>
<TR><TD>copywin()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_79">Copy</A></TD><TD><A HREF="../man/curs_overlay.3x.html">curs_overlay.3x</A></TD></TR>
<TR><TD>current_field()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_58">Current</A></TD><TD><A HREF="../man/form_page.3x.html">form_page.3x</A></TD></TR>
<TR><TD>current_item()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_14">Current</A></TD><TD><A HREF="../man/mitem_current.3x.html">mitem_current.3x</A></TD></TR>
-<TR><TD>curs_set()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_153">Set_Cursor_Visibility</A></TD><TD><A HREF="../man/curs_kernel.3x.html">curs_kernel.3x</A></TD></TR>
<TR><TD>curscr</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_2">Current_Window</A></TD><TD><A HREF="../man/curs_initscr.3x.html">curs_initscr.3x</A></TD></TR>
<TR><TD>curses_version()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_157">Curses_Version</A></TD><TD><A HREF="../man/curs_extend.3x.html">curs_extend.3x</A></TD></TR>
+<TR><TD>curs_set()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_153">Set_Cursor_Visibility</A></TD><TD><A HREF="../man/curs_kernel.3x.html">curs_kernel.3x</A></TD></TR>
<TR><TD>data_ahead()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_54">Data_Ahead</A></TD><TD><A HREF="../man/form_data.3x.html">form_data.3x</A></TD></TR>
<TR><TD>data_behind()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_55">Data_Behind</A></TD><TD><A HREF="../man/form_data.3x.html">form_data.3x</A></TD></TR>
-<TR><TD>def_prog_mode()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_148">Save_Curses_Mode</A></TD><TD><A HREF="../man/curs_kernel.3x.html">curs_kernel.3x</A></TD></TR>
<TR><TD>define_key()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_124">Define_Key</A></TD><TD><A HREF="../man/define_key.3x.html">define_key.3x</A></TD></TR>
-<TR><TD>del_panel()</TD><TD><A HREF="terminal_interface-curses-panels__ads.htm#AFU_15">Delete</A></TD><TD><A HREF="../man/panel.3x.html">panel.3x</A></TD></TR>
+<TR><TD>def_prog_mode()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_148">Save_Curses_Mode</A></TD><TD><A HREF="../man/curs_kernel.3x.html">curs_kernel.3x</A></TD></TR>
<TR><TD>delay_output()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_129">Delay_Output</A></TD><TD><A HREF="../man/curs_util.3x.html">curs_util.3x</A></TD></TR>
+<TR><TD>del_panel()</TD><TD><A HREF="terminal_interface-curses-panels__ads.htm#AFU_15">Delete</A></TD><TD><A HREF="../man/panel.3x.html">panel.3x</A></TD></TR>
<TR><TD>delwin()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_12">Delete</A></TD><TD><A HREF="../man/curs_window.3x.html">curs_window.3x</A></TD></TR>
<TR><TD>derwin()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_14">Derived_Window</A></TD><TD><A HREF="../man/curs_window.3x.html">curs_window.3x</A></TD></TR>
<TR><TD>doupdate()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_61">Update_Screen</A></TD><TD><A HREF="../man/curs_refresh.3x.html">curs_refresh.3x</A></TD></TR>
<TR><TD>field_info()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_25">Info</A></TD><TD><A HREF="../man/form_field_info.3x.html">form_field_info.3x</A></TD></TR>
<TR><TD>field_init()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_36">Get_Field_Init_Hook</A></TD><TD><A HREF="../man/form_hook.3x.html">form_hook.3x</A></TD></TR>
<TR><TD>field_just()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_7">Get_Justification</A></TD><TD><A HREF="../man/form_field_just.3x.html">form_field_just.3x</A></TD></TR>
+<TR><TD>field_opts_on()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_14">Switch_Options</A></TD><TD><A HREF="../man/form_field_opts.3x.html">form_field_opts.3x</A></TD></TR>
<TR><TD>field_opts()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_15">Get_Options</A></TD><TD><A HREF="../man/form_field_opts.3x.html">form_field_opts.3x</A></TD></TR>
<TR><TD>field_opts()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_16">Get_Options</A></TD><TD><A HREF="../man/form_field_opts.3x.html">form_field_opts.3x</A></TD></TR>
-<TR><TD>field_opts_on()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_14">Switch_Options</A></TD><TD><A HREF="../man/form_field_opts.3x.html">form_field_opts.3x</A></TD></TR>
<TR><TD>field_pad()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_24">Pad_Character</A></TD><TD><A HREF="../man/form_field_attributes.3x.html">form_field_attributes.3x</A></TD></TR>
<TR><TD>field_status()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_11">Changed</A></TD><TD><A HREF="../man/form_field_buffer.3x.html">form_field_buffer.3x</A></TD></TR>
<TR><TD>field_term()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_37">Get_Field_Term_Hook</A></TD><TD><A HREF="../man/form_hook.3x.html">form_hook.3x</A></TD></TR>
<TR><TD>form_driver()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_56">Driver</A></TD><TD><A HREF="../man/form_driver.3x.html">form_driver.3x</A></TD></TR>
<TR><TD>form_fields()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_42">Fields</A></TD><TD><A HREF="../man/form_field.3x.html">form_field.3x</A></TD></TR>
<TR><TD>form_init()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_38">Get_Form_Init_Hook</A></TD><TD><A HREF="../man/form_hook.3x.html">form_hook.3x</A></TD></TR>
+<TR><TD>form_opts_on()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_49">Switch_Options</A></TD><TD><A HREF="../man/form_opts.3x.html">form_opts.3x</A></TD></TR>
<TR><TD>form_opts()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_50">Get_Options</A></TD><TD><A HREF="../man/form_opts.3x.html">form_opts.3x</A></TD></TR>
<TR><TD>form_opts()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_51">Get_Options</A></TD><TD><A HREF="../man/form_opts.3x.html">form_opts.3x</A></TD></TR>
-<TR><TD>form_opts_on()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_49">Switch_Options</A></TD><TD><A HREF="../man/form_opts.3x.html">form_opts.3x</A></TD></TR>
<TR><TD>form_page()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_60">Page</A></TD><TD><A HREF="../man/form_page.3x.html">form_page.3x</A></TD></TR>
<TR><TD>form_sub()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_30">Get_Sub_Window</A></TD><TD><A HREF="../man/form_win.3x.html">form_win.3x</A></TD></TR>
<TR><TD>form_term()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_39">Get_Form_Term_Hook</A></TD><TD><A HREF="../man/form_hook.3x.html">form_hook.3x</A></TD></TR>
<TR><TD>initscr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_3">Init_Screen</A></TD><TD><A HREF="../man/curs_initscr.3x.html">curs_initscr.3x</A></TD></TR>
<TR><TD>initscr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_4">Init_Windows</A></TD><TD><A HREF="../man/curs_initscr.3x.html">curs_initscr.3x</A></TD></TR>
<TR><TD>intrflush()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_48">Set_Flush_On_Interrupt_Mode</A></TD><TD><A HREF="../man/curs_inopts.3x.html">curs_inopts.3x</A></TD></TR>
+<TR><TD>isendwin()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_6">Is_End_Window</A></TD><TD><A HREF="../man/curs_initscr.3x.html">curs_initscr.3x</A></TD></TR>
<TR><TD>is_linetouched()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_77">Is_Touched</A></TD><TD><A HREF="../man/curs_touch.3x.html">curs_touch.3x</A></TD></TR>
<TR><TD>is_wintouched()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_78">Is_Touched</A></TD><TD><A HREF="../man/curs_touch.3x.html">curs_touch.3x</A></TD></TR>
-<TR><TD>isendwin()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_6">Is_End_Window</A></TD><TD><A HREF="../man/curs_initscr.3x.html">curs_initscr.3x</A></TD></TR>
<TR><TD>item_count()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_58">Item_Count</A></TD><TD><A HREF="../man/menu_items.3x.html">menu_items.3x</A></TD></TR>
<TR><TD>item_description();</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_12">Description</A></TD><TD><A HREF="../man/mitem_name.3x.html">mitem_name.3x</A></TD></TR>
<TR><TD>item_index()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_17">Get_Index</A></TD><TD><A HREF="../man/mitem_current.3x.html">mitem_current.3x</A></TD></TR>
<TR><TD>item_init()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_52">Get_Item_Init_Hook</A></TD><TD><A HREF="../man/menu_hook.3x.html">menu_hook.3x</A></TD></TR>
<TR><TD>item_name()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_11">Name</A></TD><TD><A HREF="../man/mitem_name.3x.html">mitem_name.3x</A></TD></TR>
+<TR><TD>item_opts_on()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_8">Switch_Options</A></TD><TD><A HREF="../man/mitem_opts.3x.html">mitem_opts.3x</A></TD></TR>
<TR><TD>item_opts()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_10">Get_Options</A></TD><TD><A HREF="../man/mitem_opts.3x.html">mitem_opts.3x</A></TD></TR>
<TR><TD>item_opts()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_9">Get_Options</A></TD><TD><A HREF="../man/mitem_opts.3x.html">mitem_opts.3x</A></TD></TR>
-<TR><TD>item_opts_on()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_8">Switch_Options</A></TD><TD><A HREF="../man/mitem_opts.3x.html">mitem_opts.3x</A></TD></TR>
<TR><TD>item_term()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_53">Get_Item_Term_Hook</A></TD><TD><A HREF="../man/menu_hook.3x.html">menu_hook.3x</A></TD></TR>
<TR><TD>item_userptr</TD><TD><A HREF="terminal_interface-curses-menus-item_user_data__ads.htm#AFU_2">Get_User_Data</A></TD><TD><A HREF="../man/mitem_userptr.3x.html">mitem_userptr.3x</A></TD></TR>
<TR><TD>item_userptr</TD><TD><A HREF="terminal_interface-curses-menus-item_user_data__ads.htm#AFU_3">Get_User_Data</A></TD><TD><A HREF="../man/mitem_userptr.3x.html">mitem_userptr.3x</A></TD></TR>
<TR><TD>menu_init()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_54">Get_Menu_Init_Hook</A></TD><TD><A HREF="../man/menu_hook.3x.html">menu_hook.3x</A></TD></TR>
<TR><TD>menu_items()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_57">Items</A></TD><TD><A HREF="../man/menu_items.3x.html">menu_items.3x</A></TD></TR>
<TR><TD>menu_mark()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_30">Mark</A></TD><TD><A HREF="../man/menu_mark.3x.html">menu_mark.3x</A></TD></TR>
+<TR><TD>menu_opts_on()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_20">Switch_Options</A></TD><TD><A HREF="../man/menu_opts.3x.html">menu_opts.3x</A></TD></TR>
<TR><TD>menu_opts()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_21">Get_Options</A></TD><TD><A HREF="../man/menu_opts.3x.html">menu_opts.3x</A></TD></TR>
<TR><TD>menu_opts()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_22">Get_Options</A></TD><TD><A HREF="../man/menu_opts.3x.html">menu_opts.3x</A></TD></TR>
-<TR><TD>menu_opts_on()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_20">Switch_Options</A></TD><TD><A HREF="../man/menu_opts.3x.html">menu_opts.3x</A></TD></TR>
<TR><TD>menu_pad()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_41">Pad_Character</A></TD><TD><A HREF="../man/menu_attributes.3x.html">menu_attributes.3x</A></TD></TR>
<TR><TD>menu_pattern()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_45">Pattern</A></TD><TD><A HREF="../man/menu_pattern.3x.html">menu_pattern.3x</A></TD></TR>
<TR><TD>menu_requestname.3x</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_62"></A></TD><TD><A HREF="../man/menu_driver.3x.html">menu_driver.3x</A></TD></TR>
<TR><TD>move_field()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_44">Move</A></TD><TD><A HREF="../man/form_field.3x.html">form_field.3x</A></TD></TR>
<TR><TD>move_panel()</TD><TD><A HREF="terminal_interface-curses-panels__ads.htm#AFU_11">Move</A></TD><TD><A HREF="../man/panel.3x.html">panel.3x</A></TD></TR>
<TR><TD>mvderwin()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_17">Move_Derived_Window</A></TD><TD><A HREF="../man/curs_window.3x.html">curs_window.3x</A></TD></TR>
-<TR><TD>mvwaddch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_9">Add</A></TD><TD><A HREF="../man/curs_addch.3x.html">curs_addch.3x</A></TD></TR>
<TR><TD>mvwaddchnstr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_24">Add</A></TD><TD><A HREF="../man/curs_addchstr.3x.html">curs_addchstr.3x</A></TD></TR>
+<TR><TD>mvwaddch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_9">Add</A></TD><TD><A HREF="../man/curs_addch.3x.html">curs_addch.3x</A></TD></TR>
<TR><TD>mvwaddnstr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_22">Add</A></TD><TD><A HREF="../man/curs_addstr.3x.html">curs_addstr.3x</A></TD></TR>
<TR><TD>mvwchgat()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_39">Change_Attributes</A></TD><TD><A HREF="../man/curs_attr.3x.html">curs_attr.3x</A></TD></TR>
<TR><TD>mvwdelch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_96">Delete_Character</A></TD><TD><A HREF="../man/curs_delch.3x.html">curs_delch.3x</A></TD></TR>
<TR><TD>mvwgetnstr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_108">Get</A></TD><TD><A HREF="../man/curs_getstr.3x.html">curs_getstr.3x</A></TD></TR>
-<TR><TD>mvwin()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_16">Move_Window</A></TD><TD><A HREF="../man/curs_window.3x.html">curs_window.3x</A></TD></TR>
-<TR><TD>mvwinch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_98">Peek</A></TD><TD><A HREF="../man/curs_inch.3x.html">curs_inch.3x</A></TD></TR>
<TR><TD>mvwinchnstr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_106">Peek</A></TD><TD><A HREF="../man/curs_inchstr.3x.html">curs_inchstr.3x</A></TD></TR>
+<TR><TD>mvwinch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_98">Peek</A></TD><TD><A HREF="../man/curs_inch.3x.html">curs_inch.3x</A></TD></TR>
<TR><TD>mvwinnstr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_104">Peek</A></TD><TD><A HREF="../man/curs_instr.3x.html">curs_instr.3x</A></TD></TR>
<TR><TD>mvwinsch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_100">Insert</A></TD><TD><A HREF="../man/curs_insch.3x.html">curs_insch.3x</A></TD></TR>
<TR><TD>mvwinsnstr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_102">Insert</A></TD><TD><A HREF="../man/curs_insstr.3x.html">curs_insstr.3x</A></TD></TR>
+<TR><TD>mvwin()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_16">Move_Window</A></TD><TD><A HREF="../man/curs_window.3x.html">curs_window.3x</A></TD></TR>
<TR><TD>napms()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_154">Nap_Milli_Seconds</A></TD><TD><A HREF="../man/curs_kernel.3x.html">curs_kernel.3x</A></TD></TR>
+<TR><TD>_nc_freeall()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_159">Curses_Free_All</A></TD><TD><A HREF="../man/curs_trace.3x.html">curs_trace.3x</A></TD></TR>
<TR><TD>new_field()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_1">Create</A></TD><TD><A HREF="../man/form_field_new.3x.html">form_field_new.3x</A></TD></TR>
<TR><TD>new_field()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_2">New_Field</A></TD><TD><A HREF="../man/form_field_new.3x.html">form_field_new.3x</A></TD></TR>
<TR><TD>new_form()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_45">Create</A></TD><TD><A HREF="../man/form_new.3x.html">form_new.3x</A></TD></TR>
<TR><TD>new_item()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_1">Create</A></TD><TD><A HREF="../man/mitem_new.3x.html">mitem_new.3x</A></TD></TR>
<TR><TD>new_item()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_2">New_Item</A></TD><TD><A HREF="../man/mitem_new.3x.html">mitem_new.3x</A></TD></TR>
<TR><TD>new_menu()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_59">Create</A></TD><TD><A HREF="../man/menu_new.3x.html">menu_new.3x</A></TD></TR>
+<TR><TD>newpad()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_89">New_Pad</A></TD><TD><A HREF="../man/curs_pad.3x.html">curs_pad.3x</A></TD></TR>
<TR><TD>new_page()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_63">Is_New_Page</A></TD><TD><A HREF="../man/form_new_page.3x.html">form_new_page.3x</A></TD></TR>
<TR><TD>new_panel()</TD><TD><A HREF="terminal_interface-curses-panels__ads.htm#AFU_1">Create</A></TD><TD><A HREF="../man/panel.3x.html">panel.3x</A></TD></TR>
<TR><TD>new_panel()</TD><TD><A HREF="terminal_interface-curses-panels__ads.htm#AFU_2">New_Panel</A></TD><TD><A HREF="../man/panel.3x.html">panel.3x</A></TD></TR>
-<TR><TD>newpad()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_89">New_Pad</A></TD><TD><A HREF="../man/curs_pad.3x.html">curs_pad.3x</A></TD></TR>
<TR><TD>newwin()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_11">Create</A></TD><TD><A HREF="../man/curs_window.3x.html">curs_window.3x</A></TD></TR>
<TR><TD>nl()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_53">Set_NL_Mode</A></TD><TD><A HREF="../man/curs_outopts.3x.html">curs_outopts.3x</A></TD></TR>
<TR><TD>nodelay()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_50">Set_NoDelay_Mode</A></TD><TD><A HREF="../man/curs_inopts.3x.html">curs_inopts.3x</A></TD></TR>
<TR><TD>scale_menu()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_27">Scale</A></TD><TD><A HREF="../man/menu_win.3x.html">menu_win.3x</A></TD></TR>
<TR><TD>scr_dump()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_160">Screen_Dump_To_File</A></TD><TD><A HREF="../man/curs_scr_dump.3x.html">curs_scr_dump.3x</A></TD></TR>
<TR><TD>scr_init()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_162">Screen_Init_From_File</A></TD><TD><A HREF="../man/curs_scr_dump.3x.html">curs_scr_dump.3x</A></TD></TR>
+<TR><TD>scrollok()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_59">Allow_Scrolling</A></TD><TD><A HREF="../man/curs_outopts.3x.html">curs_outopts.3x</A></TD></TR>
<TR><TD>scr_restore()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_161">Screen_Restore_From_File</A></TD><TD><A HREF="../man/curs_scr_dump.3x.html">curs_scr_dump.3x</A></TD></TR>
<TR><TD>scr_set()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_163">Screen_Set_File</A></TD><TD><A HREF="../man/curs_scr_dump.3x.html">curs_scr_dump.3x</A></TD></TR>
-<TR><TD>scrollok()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_59">Allow_Scrolling</A></TD><TD><A HREF="../man/curs_outopts.3x.html">curs_outopts.3x</A></TD></TR>
<TR><TD>set_current_field()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_57">Set_Current</A></TD><TD><A HREF="../man/form_page.3x.html">form_page.3x</A></TD></TR>
<TR><TD>set_current_item()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_13">Set_Current</A></TD><TD><A HREF="../man/mitem_current.3x.html">mitem_current.3x</A></TD></TR>
<TR><TD>set_field_back()</TD><TD><A HREF="terminal_interface-curses-forms__ads.htm#AFU_20">Set_Background</A></TD><TD><A HREF="../man/form_field_attributes.3x.html">form_field_attributes.3x</A></TD></TR>
<TR><TD>set_panel_userptr</TD><TD><A HREF="terminal_interface-curses-panels-user_data__ads.htm#AFU_1">Set_User_Data</A></TD><TD><A HREF="../man/panel.3x.html">panel.3x</A></TD></TR>
<TR><TD>set_top_row()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_15">Set_Top_Row</A></TD><TD><A HREF="../man/mitem_current.3x.html">mitem_current.3x</A></TD></TR>
<TR><TD>show_panel()</TD><TD><A HREF="terminal_interface-curses-panels__ads.htm#AFU_5">Show</A></TD><TD><A HREF="../man/panel.3x.html">panel.3x</A></TD></TR>
-<TR><TD>slk_attr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_120">Get_Soft_Label_Key_Attributes</A></TD><TD><A HREF="../man/curs_slk.3x.html">curs_slk.3x</A></TD></TR>
-<TR><TD>slk_attr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_121">Get_Soft_Label_Key_Attributes</A></TD><TD><A HREF="../man/curs_slk.3x.html">curs_slk.3x</A></TD></TR>
<TR><TD>slk_attron()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_118">Switch_Soft_Label_Key_Attributes</A></TD><TD><A HREF="../man/curs_slk.3x.html">curs_slk.3x</A></TD></TR>
<TR><TD>slk_attrset()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_119">Set_Soft_Label_Key_Attributes</A></TD><TD><A HREF="../man/curs_slk.3x.html">curs_slk.3x</A></TD></TR>
+<TR><TD>slk_attr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_120">Get_Soft_Label_Key_Attributes</A></TD><TD><A HREF="../man/curs_slk.3x.html">curs_slk.3x</A></TD></TR>
+<TR><TD>slk_attr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_121">Get_Soft_Label_Key_Attributes</A></TD><TD><A HREF="../man/curs_slk.3x.html">curs_slk.3x</A></TD></TR>
<TR><TD>slk_clear()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_115">Clear_Soft_Label_Keys</A></TD><TD><A HREF="../man/curs_slk.3x.html">curs_slk.3x</A></TD></TR>
<TR><TD>slk_color()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_122">Set_Soft_Label_Key_Color</A></TD><TD><A HREF="../man/curs_slk.3x.html">curs_slk.3x</A></TD></TR>
<TR><TD>slk_init()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_109">Init_Soft_Label_Keys</A></TD><TD><A HREF="../man/curs_slk.3x.html">curs_slk.3x</A></TD></TR>
<TR><TD>top_row()</TD><TD><A HREF="terminal_interface-curses-menus__ads.htm#AFU_16">Top_Row</A></TD><TD><A HREF="../man/mitem_current.3x.html">mitem_current.3x</A></TD></TR>
<TR><TD>touchline()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_75">Touch</A></TD><TD><A HREF="../man/curs_touch.3x.html">curs_touch.3x</A></TD></TR>
<TR><TD>touchwin()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_74">Touch</A></TD><TD><A HREF="../man/curs_touch.3x.html">curs_touch.3x</A></TD></TR>
+<TR><TD>_tracef()</TD><TD><A HREF="terminal_interface-curses-trace__ads.htm#AFU_2">Trace_Put</A></TD><TD><A HREF="../man/curs_trace.3x.html">curs_trace.3x</A></TD></TR>
<TR><TD>trace()</TD><TD><A HREF="terminal_interface-curses-trace__ads.htm#AFU_1">Trace_on</A></TD><TD><A HREF="../man/curs_trace.3x.html">curs_trace.3x</A></TD></TR>
<TR><TD>unctrl()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_127">Un_Control</A></TD><TD><A HREF="../man/curs_util.3x.html">curs_util.3x</A></TD></TR>
<TR><TD>unctrl()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_128">Un_Control</A></TD><TD><A HREF="../man/curs_util.3x.html">curs_util.3x</A></TD></TR>
<TR><TD>update_panels()</TD><TD><A HREF="terminal_interface-curses-panels__ads.htm#AFU_6">Update_Panels</A></TD><TD><A HREF="../man/panel.3x.html">panel.3x</A></TD></TR>
<TR><TD>use_default_colors()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_155">Use_Default_Colors</A></TD><TD><A HREF="../man/default_colors.3x.html">default_colors.3x</A></TD></TR>
<TR><TD>use_extended_names()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_158">Use_Extended_Names</A></TD><TD><A HREF="../man/curs_extend.3x.html">curs_extend.3x</A></TD></TR>
-<TR><TD>waddch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_8">Add</A></TD><TD><A HREF="../man/curs_addch.3x.html">curs_addch.3x</A></TD></TR>
<TR><TD>waddchnstr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_23">Add</A></TD><TD><A HREF="../man/curs_addchstr.3x.html">curs_addchstr.3x</A></TD></TR>
+<TR><TD>waddch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_8">Add</A></TD><TD><A HREF="../man/curs_addch.3x.html">curs_addch.3x</A></TD></TR>
<TR><TD>waddnstr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_21">Add</A></TD><TD><A HREF="../man/curs_addstr.3x.html">curs_addstr.3x</A></TD></TR>
<TR><TD>wattr_get()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_35">Get_Character_Attributes</A></TD><TD><A HREF="../man/curs_attr.3x.html">curs_attr.3x</A></TD></TR>
<TR><TD>wattr_get()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_36">Get_Character_Attribute</A></TD><TD><A HREF="../man/curs_attr.3x.html">curs_attr.3x</A></TD></TR>
<TR><TD>wattron()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_33">Switch_Character_Attribute</A></TD><TD><A HREF="../man/curs_attr.3x.html">curs_attr.3x</A></TD></TR>
<TR><TD>wattrset()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_34">Set_Character_Attributes</A></TD><TD><A HREF="../man/curs_attr.3x.html">curs_attr.3x</A></TD></TR>
-<TR><TD>wbkgd()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_71">Change_Background</A></TD><TD><A HREF="../man/curs_bkgd.3x.html">curs_bkgd.3x</A></TD></TR>
<TR><TD>wbkgdget()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_72">Get_Background</A></TD><TD><A HREF="../man/curs_bkgd.3x.html">curs_bkgd.3x</A></TD></TR>
<TR><TD>wbkgdset()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_70">Set_Background</A></TD><TD><A HREF="../man/curs_bkgd.3x.html">curs_bkgd.3x</A></TD></TR>
+<TR><TD>wbkgd()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_71">Change_Background</A></TD><TD><A HREF="../man/curs_bkgd.3x.html">curs_bkgd.3x</A></TD></TR>
<TR><TD>wborder()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_25">Border</A></TD><TD><A HREF="../man/curs_border.3x.html">curs_border.3x</A></TD></TR>
<TR><TD>wchgat()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_38">Change_Attributes</A></TD><TD><A HREF="../man/curs_attr.3x.html">curs_attr.3x</A></TD></TR>
<TR><TD>wclear()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_67">Clear</A></TD><TD><A HREF="../man/curs_clear.3x.html">curs_clear.3x</A></TD></TR>
<TR><TD>wgetch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_29">Get_Keystroke</A></TD><TD><A HREF="../man/curs_getch.3x.html">curs_getch.3x</A></TD></TR>
<TR><TD>wgetnstr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_107">Get</A></TD><TD><A HREF="../man/curs_getstr.3x.html">curs_getstr.3x</A></TD></TR>
<TR><TD>whline()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_27">Horizontal_Line</A></TD><TD><A HREF="../man/curs_border.3x.html">curs_border.3x</A></TD></TR>
-<TR><TD>winch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_97">Peek</A></TD><TD><A HREF="../man/curs_inch.3x.html">curs_inch.3x</A></TD></TR>
<TR><TD>winchnstr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_105">Peek</A></TD><TD><A HREF="../man/curs_inchstr.3x.html">curs_inchstr.3x</A></TD></TR>
+<TR><TD>winch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_97">Peek</A></TD><TD><A HREF="../man/curs_inch.3x.html">curs_inch.3x</A></TD></TR>
<TR><TD>winnstr()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_103">Peek</A></TD><TD><A HREF="../man/curs_instr.3x.html">curs_instr.3x</A></TD></TR>
<TR><TD>winsch()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_99">Insert</A></TD><TD><A HREF="../man/curs_insch.3x.html">curs_insch.3x</A></TD></TR>
<TR><TD>winsdelln()</TD><TD><A HREF="terminal_interface-curses__ads.htm#AFU_82">Insert_Delete_Lines</A></TD><TD><A HREF="../man/curs_deleteln.3x.html">curs_deleteln.3x</A></TD></TR>
<span class="comment"><EM>-- S P E C --</EM></span>
<span class="comment"><EM>-- --</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
-<span class="comment"><EM>-- Copyright (c) 1998 Free Software Foundation, Inc. --</EM></span>
+<span class="comment"><EM>-- Copyright (c) 1998,2003 Free Software Foundation, Inc. --</EM></span>
<span class="comment"><EM>-- --</EM></span>
<span class="comment"><EM>-- Permission is hereby granted, free of charge, to any person obtaining a --</EM></span>
<span class="comment"><EM>-- copy of this software and associated documentation files (the --</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
<span class="comment"><EM>-- Author: Juergen Pfeifer, 1996</EM></span>
<span class="comment"><EM>-- Version Control:</EM></span>
-<span class="comment"><EM>-- @Revision: 1.10 @</EM></span>
+<span class="comment"><EM>-- @Revision: 1.11 @</EM></span>
<span class="comment"><EM>-- Binding Version 01.00</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
<b>generic</b>
<span class="comment"><EM>-- B O D Y --</EM></span>
<span class="comment"><EM>-- --</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
-<span class="comment"><EM>-- Copyright (c) 2000 Free Software Foundation, Inc. --</EM></span>
+<span class="comment"><EM>-- Copyright (c) 2000,2003 Free Software Foundation, Inc. --</EM></span>
<span class="comment"><EM>-- --</EM></span>
<span class="comment"><EM>-- Permission is hereby granted, free of charge, to any person obtaining a --</EM></span>
<span class="comment"><EM>-- copy of this software and associated documentation files (the --</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
<span class="comment"><EM>-- Author: Juergen Pfeifer, 1996</EM></span>
<span class="comment"><EM>-- Version Control:</EM></span>
-<span class="comment"><EM>-- @Revision: 1.3 @</EM></span>
+<span class="comment"><EM>-- @Revision: 1.4 @</EM></span>
<span class="comment"><EM>-- Binding Version 01.00</EM></span>
<b>with</b> Ada.Streams.Stream_IO.C_Streams;
<span class="comment"><EM>-- S P E C --</EM></span>
<span class="comment"><EM>-- --</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
-<span class="comment"><EM>-- Copyright (c) 2000 Free Software Foundation, Inc. --</EM></span>
+<span class="comment"><EM>-- Copyright (c) 2000,2003 Free Software Foundation, Inc. --</EM></span>
<span class="comment"><EM>-- --</EM></span>
<span class="comment"><EM>-- Permission is hereby granted, free of charge, to any person obtaining a --</EM></span>
<span class="comment"><EM>-- copy of this software and associated documentation files (the --</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
<span class="comment"><EM>-- Author: Juergen Pfeifer, 1996</EM></span>
<span class="comment"><EM>-- Version Control:</EM></span>
-<span class="comment"><EM>-- @Revision: 1.3 @</EM></span>
+<span class="comment"><EM>-- @Revision: 1.4 @</EM></span>
<span class="comment"><EM>-- Binding Version 01.00</EM></span>
<b>with</b> Ada.Streams.Stream_IO;
<span class="comment"><EM>-- S P E C --</EM></span>
<span class="comment"><EM>-- --</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
-<span class="comment"><EM>-- Copyright (c) 2000 Free Software Foundation, Inc. --</EM></span>
+<span class="comment"><EM>-- Copyright (c) 2000,2003 Free Software Foundation, Inc. --</EM></span>
<span class="comment"><EM>-- --</EM></span>
<span class="comment"><EM>-- Permission is hereby granted, free of charge, to any person obtaining a --</EM></span>
<span class="comment"><EM>-- copy of this software and associated documentation files (the --</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
<span class="comment"><EM>-- Author: Juergen Pfeifer, 1996</EM></span>
<span class="comment"><EM>-- Version Control:</EM></span>
-<span class="comment"><EM>-- @Revision: 1.3 @</EM></span>
+<span class="comment"><EM>-- @Revision: 1.4 @</EM></span>
<span class="comment"><EM>-- Binding Version 01.00</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
<span class="comment"><EM>-- S P E C --</EM></span>
<span class="comment"><EM>-- --</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
-<span class="comment"><EM>-- Copyright (c) 2000 Free Software Foundation, Inc. --</EM></span>
+<span class="comment"><EM>-- Copyright (c) 2000,2003 Free Software Foundation, Inc. --</EM></span>
<span class="comment"><EM>-- --</EM></span>
<span class="comment"><EM>-- Permission is hereby granted, free of charge, to any person obtaining a --</EM></span>
<span class="comment"><EM>-- copy of this software and associated documentation files (the --</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
<span class="comment"><EM>-- Author: Juergen Pfeifer, 1996</EM></span>
<span class="comment"><EM>-- Version Control:</EM></span>
-<span class="comment"><EM>-- @Revision: 1.3 @</EM></span>
+<span class="comment"><EM>-- @Revision: 1.4 @</EM></span>
<span class="comment"><EM>-- Binding Version 01.00</EM></span>
<span class="comment"><EM>------------------------------------------------------------------------------</EM></span>
</PRE><H2><a name="h2-SEE-ALSO">SEE ALSO</a></H2><PRE>
<STRONG><A HREF="ncurses.3x.html">curses(3x)</A></STRONG>
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
</PRE><H2><a name="h2-SEE-ALSO">SEE ALSO</a></H2><PRE>
<STRONG><A HREF="infocmp.1m.html">infocmp(1m)</A></STRONG>, <STRONG><A HREF="ncurses.3x.html">curses(3x)</A></STRONG>, <STRONG><A HREF="terminfo.5.html">terminfo(5)</A></STRONG>
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
</PRE><H2><a name="h2-AUTHOR">AUTHOR</a></H2><PRE>
</PRE><H2><a name="h2-SEE-ALSO">SEE ALSO</a></H2><PRE>
<STRONG><A HREF="tput.1.html">tput(1)</A></STRONG>, <STRONG><A HREF="terminfo.5.html">terminfo(5)</A></STRONG>
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
* sale, use or other dealings in this Software without prior written *
* authorization. *
****************************************************************************
- * @Id: curs_addch.3x,v 1.38 2017/01/07 19:25:15 tom Exp @
+ * @Id: curs_addch.3x,v 1.39 2017/04/17 00:14:02 tom Exp @
-->
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01//EN">
<HTML>
The <STRONG>addch</STRONG>, <STRONG>waddch</STRONG>, <STRONG>mvaddch</STRONG> and <STRONG>mvwaddch</STRONG> routines put the
character <EM>ch</EM> into the given window at its current window
position, which is then advanced. They are analogous to
- <STRONG>putchar</STRONG> in <STRONG>stdio(3)</STRONG>. If the advance is at the right mar-
- gin:
+ <STRONG>putchar(3)</STRONG> in <STRONG>stdio(3)</STRONG>. If the advance is at the right
+ margin:
<STRONG>o</STRONG> The cursor automatically wraps to the beginning of the
next line.
<!--
****************************************************************************
- * Copyright (c) 1998-2006,2010 Free Software Foundation, Inc. *
+ * Copyright (c) 1998-2010,2017 Free Software Foundation, Inc. *
* *
* Permission is hereby granted, free of charge, to any person obtaining a *
* copy of this software and associated documentation files (the *
* sale, use or other dealings in this Software without prior written *
* authorization. *
****************************************************************************
- * @Id: curs_scanw.3x,v 1.17 2010/12/04 18:40:45 tom Exp @
+ * @Id: curs_scanw.3x,v 1.18 2017/04/17 00:07:02 tom Exp @
-->
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01//EN">
<HTML>
ing line used as input for <STRONG>sscanf(3)</STRONG>. Fields which do not
map to a variable in the <EM>fmt</EM> field are lost.
- The <STRONG>vwscanw</STRONG> and <STRONG>vw_scanw</STRONG> routines are analogous to <STRONG>vscanf</STRONG>.
- They perform a <STRONG>wscanw</STRONG> using a variable argument list. The
- third argument is a <EM>va</EM><STRONG>_</STRONG><EM>list</EM>, a pointer to a list of argu-
- ments, as defined in <STRONG><stdarg.h></STRONG>.
+ The <STRONG>vwscanw</STRONG> and <STRONG>vw_scanw</STRONG> routines are analogous to
+ <STRONG>vscanf(3)</STRONG>. They perform a <STRONG>wscanw</STRONG> using a variable argu-
+ ment list. The third argument is a <EM>va</EM><STRONG>_</STRONG><EM>list</EM>, a pointer to
+ a list of arguments, as defined in <STRONG><stdarg.h></STRONG>.
</PRE><H2><a name="h2-RETURN-VALUE">RETURN VALUE</a></H2><PRE>
Both XSI and The Single Unix Specification, Version 2
state that these functions return ERR or OK. Since the
- underlying <STRONG>scanf</STRONG> can return the number of items scanned,
- and the SVr4 code was documented to use this feature, this
- is probably an editing error which was introduced in XSI,
- rather than being done intentionally. Portable applica-
- tions should only test if the return value is ERR, since
- the OK value (zero) is likely to be misleading. One pos-
- sible way to get useful results would be to use a "%n"
- conversion at the end of the format string to ensure that
- something was processed.
+ underlying <STRONG>scanf(3)</STRONG> can return the number of items
+ scanned, and the SVr4 code was documented to use this fea-
+ ture, this is probably an editing error which was intro-
+ duced in XSI, rather than being done intentionally. Por-
+ table applications should only test if the return value is
+ ERR, since the OK value (zero) is likely to be misleading.
+ One possible way to get useful results would be to use a
+ "%n" conversion at the end of the format string to ensure
+ that something was processed.
</PRE><H2><a name="h2-SEE-ALSO">SEE ALSO</a></H2><PRE>
* sale, use or other dealings in this Software without prior written *
* authorization. *
****************************************************************************
- * @Id: curs_scr_dump.3x,v 1.10 2017/01/07 19:25:15 tom Exp @
+ * @Id: curs_scr_dump.3x,v 1.11 2017/04/17 00:41:24 tom Exp @
-->
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01//EN">
<HTML>
</PRE><H2><a name="h2-SEE-ALSO">SEE ALSO</a></H2><PRE>
<STRONG><A HREF="ncurses.3x.html">curses(3x)</A></STRONG>, <STRONG><A HREF="curs_initscr.3x.html">curs_initscr(3x)</A></STRONG>, <STRONG><A HREF="curs_refresh.3x.html">curs_refresh(3x)</A></STRONG>,
- <STRONG><A HREF="curs_util.3x.html">curs_util(3x)</A></STRONG>, <STRONG>system(3)</STRONG>
+ <STRONG><A HREF="curs_util.3x.html">curs_util(3x)</A></STRONG>, <STRONG><A HREF="scr_dump.5.html">scr_dump(5)</A></STRONG>, <STRONG>system(3)</STRONG>
* sale, use or other dealings in this Software without prior written *
* authorization. *
****************************************************************************
- * @Id: curs_util.3x,v 1.47 2017/02/18 16:43:03 tom Exp @
+ * @Id: curs_util.3x,v 1.48 2017/04/22 14:05:14 tom Exp @
-->
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01//EN">
<HTML>
KEY_MAX, but are not guaranteed to be the same value for
different runs because user-defined codes are merged from
all terminal descriptions which have been loaded. The
- <STRONG>use_extended_names</STRONG> function controls whether this data is
- loaded when the terminal description is read by the li-
+ <STRONG><A HREF="curs_extend.3x.html">use_extended_names(3x)</A></STRONG> function controls whether this data
+ is loaded when the terminal description is read by the li-
brary.
<STRONG><A HREF="ncurses.3x.html">curses(3x)</A></STRONG> and related pages whose names begin "form_" for
detailed descriptions of the entry points.
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
<!--
- $Id: index.html,v 1.7 2013/06/07 20:12:36 tom Exp $
+ $Id: index.html,v 1.10 2017/04/17 01:01:04 tom Exp $
****************************************************************************
- * Copyright (c) 1998-2010,2013 Free Software Foundation, Inc. *
+ * Copyright (c) 1998-2013,2017 Free Software Foundation, Inc. *
* *
* Permission is hereby granted, free of charge, to any person obtaining a *
* copy of this software and associated documentation files (the *
</ul>
</li>
+ <li>Scripts:
+
+ <ul>
+ <li><a href=
+ "adacurses6-config.1.html">adacurses*-config</a> –
+ helper script for AdaCurses libraries</li>
+
+ <li><a href="ncurses6-config.1.html">ncurses*-config</a>
+ – helper script for ncurses libraries</li>
+ </ul>
+ </li>
+
<li>Libraries:
<ul>
<li><a href="ncurses.3x.html">ncurses – CRT screen
handling and optimization package</a></li>
- <li><a href="panel.3x.html">panel- panel stack extension
- for curses</a></li>
+ <li><a href="panel.3x.html">panel – panel stack
+ extension for curses</a></li>
<li><a href="form.3x.html">form – curses extension
for programming forms</a></li>
<li><a href="term.5.html">term – format of compiled
term file.</a></li>
+ <li><a href="scr_dump.5.html">scr_dump – format of
+ curses screen dumps.</a></li>
+
<li><a href="term.7.html">term – conventions for
naming terminal types</a></li>
</ul>
http://invisible-island.net/ncurses/tctest.html
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
</PRE><H2><a name="h2-AUTHOR">AUTHOR</a></H2><PRE>
</PRE><H2><a name="h2-SEE-ALSO">SEE ALSO</a></H2><PRE>
<STRONG><A HREF="ncurses.3x.html">curses(3x)</A></STRONG>, <STRONG><A HREF="tic.1m.html">tic(1m)</A></STRONG>, <STRONG><A HREF="infocmp.1m.html">infocmp(1m)</A></STRONG>, <STRONG><A HREF="terminfo.5.html">terminfo(5)</A></STRONG>
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
</PRE><H2><a name="h2-AUTHOR">AUTHOR</a></H2><PRE>
<STRONG><A HREF="ncurses.3x.html">curses(3x)</A></STRONG> and related pages whose names begin "menu_" for
detailed descriptions of the entry points.
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
sonable optimization. This implementation is "new curses"
(ncurses) and is the approved replacement for 4.4BSD clas-
sic curses, which has been discontinued. This describes
- <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
The <STRONG>ncurses</STRONG> library emulates the curses library of System
V Release 4 UNIX, and XPG4 (X/Open Portability Guide)
</PRE><H2><a name="h2-SEE-ALSO">SEE ALSO</a></H2><PRE>
<STRONG><A HREF="ncurses.3x.html">curses(3x)</A></STRONG>
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
</PRE><H2><a name="h2-SEE-ALSO">SEE ALSO</a></H2><PRE>
<STRONG><A HREF="ncurses.3x.html">curses(3x)</A></STRONG>, <STRONG><A HREF="curs_variables.3x.html">curs_variables(3x)</A></STRONG>,
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
</PRE><H2><a name="h2-AUTHOR">AUTHOR</a></H2><PRE>
--- /dev/null
+<!--
+ ****************************************************************************
+ * Copyright (c) 2017 Free Software Foundation, Inc. *
+ * *
+ * Permission is hereby granted, free of charge, to any person obtaining a *
+ * copy of this software and associated documentation files (the *
+ * "Software"), to deal in the Software without restriction, including *
+ * without limitation the rights to use, copy, modify, merge, publish, *
+ * distribute, distribute with modifications, sublicense, and/or sell *
+ * copies of the Software, and to permit persons to whom the Software is *
+ * furnished to do so, subject to the following conditions: *
+ * *
+ * The above copyright notice and this permission notice shall be included *
+ * in all copies or substantial portions of the Software. *
+ * *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS *
+ * OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF *
+ * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. *
+ * IN NO EVENT SHALL THE ABOVE COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, *
+ * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR *
+ * OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR *
+ * THE USE OR OTHER DEALINGS IN THE SOFTWARE. *
+ * *
+ * Except as contained in this notice, the name(s) of the above copyright *
+ * holders shall not be used in advertising or otherwise to promote the *
+ * sale, use or other dealings in this Software without prior written *
+ * authorization. *
+ ****************************************************************************
+ * @Id: scr_dump.5,v 1.9 2017/04/22 18:44:25 tom Exp @
+-->
+<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01//EN">
+<HTML>
+<HEAD>
+<meta http-equiv="Content-Type" content="text/html; charset=us-ascii">
+<meta name="generator" content="Manpage converted by man2html - see http://invisible-island.net/scripts/readme.html#others_scripts">
+<TITLE>scr_dump 5</TITLE>
+<link rev=made href="mailto:bug-ncurses@gnu.org">
+<meta http-equiv="Content-Type" content="text/html; charset=iso-8859-1">
+</HEAD>
+<BODY>
+<H1 class="no-header">scr_dump 5</H1>
+<PRE>
+<STRONG><A HREF="scr_dump.5.html">scr_dump(5)</A></STRONG> <STRONG><A HREF="scr_dump.5.html">scr_dump(5)</A></STRONG>
+
+
+
+
+</PRE><H2><a name="h2-NAME">NAME</a></H2><PRE>
+ scr_dump - format of curses screen-dumps.
+
+
+</PRE><H2><a name="h2-SYNOPSIS">SYNOPSIS</a></H2><PRE>
+ <STRONG>scr_dump</STRONG>
+
+
+</PRE><H2><a name="h2-DESCRIPTION">DESCRIPTION</a></H2><PRE>
+ The curses library provides applications with the ability
+ to write the contents of a window to an external file
+ using <STRONG>scr_dump</STRONG> or <STRONG>putwin</STRONG>, and read it back using
+ <STRONG>scr_restore</STRONG> or <STRONG>getwin</STRONG>.
+
+ The <STRONG>putwin</STRONG> and <STRONG>getwin</STRONG> functions do the work; while
+ <STRONG>scr_dump</STRONG> and <STRONG>scr_restore</STRONG> conveniently save and restore the
+ whole screen, i.e., <STRONG>stdscr</STRONG>.
+
+
+</PRE><H3><a name="h3-ncurses6">ncurses6</a></H3><PRE>
+ A longstanding implementation of screen-dump was revised
+ with ncurses6 to remedy problems with the earlier
+ approach:
+
+ <STRONG>o</STRONG> A "magic number" is written to the beginning of the
+ dump file, allowing applications (such as <STRONG>file(1)</STRONG>) to
+ recognize curses dump files.
+
+ Because ncurses6 uses a new format, that requires a
+ new magic number was unused by other applications.
+ This 16-bit number was unused:
+
+ 0x8888 (octal "\210\210")
+
+ but to be more certain, this 32-bit number was chosen:
+
+ 0x88888888 (octal "\210\210\210\210")
+
+ This is the pattern submitted to the maintainers of
+ the <STRONG>file</STRONG> program:
+
+ #
+ # ncurses5 (and before) did not use a magic number,
+ # making screen dumps "data".
+ #
+ # ncurses6 (2015) uses this format, ignoring byte-order
+ 0 string \210\210\210\210ncurses ncurses6 screen image
+ #
+
+ <STRONG>o</STRONG> The screen dumps are written in textual form, so that
+ internal data sizes are not directly related to the
+ dump-format, and enabling the library to read dumps
+ from either narrow- or wide-character- configurations.
+
+ The <EM>narrow</EM> library configuration holds characters and
+ video attributes in a 32-bit <STRONG>chtype</STRONG>, while the <EM>wide-</EM>
+ <EM>character</EM> library stores this information in the
+ <STRONG>cchar_t</STRONG> structure, which is much larger than 32-bits.
+
+ <STRONG>o</STRONG> It is possible to read a screen dump into a terminal
+ with a different screen-size, because the library
+ truncates or fills the screen as necessary.
+
+ <STRONG>o</STRONG> The ncurses6 <STRONG>getwin</STRONG> reads the legacy screen dumps from
+ ncurses5.
+
+
+</PRE><H3><a name="h3-ncurses5-_legacy_">ncurses5 (legacy)</a></H3><PRE>
+ The screen-dump feature was added to ncurses in June 1995.
+ While there were fixes and improvements in succeeding
+ years, the basic scheme was unchanged:
+
+ <STRONG>o</STRONG> The <STRONG>WINDOW</STRONG> structure was written in binary form.
+
+ <STRONG>o</STRONG> The <STRONG>WINDOW</STRONG> structure refers to lines of data, which
+ were written as an array of binary data following the
+ <STRONG>WINDOW</STRONG>.
+
+ <STRONG>o</STRONG> When <STRONG>getwin</STRONG> restored the window, it would keep track
+ of offsets into the array of line-data and adjust the
+ <STRONG>WINDOW</STRONG> structure which was read back into memory.
+
+ This is similar to Unix SystemV, but does not write a
+ "magic number" to identify the file format.
+
+
+</PRE><H2><a name="h2-PORTABILITY">PORTABILITY</a></H2><PRE>
+ There is no standard format for <STRONG>putwin</STRONG>. This section
+ gives a brief description of the existing formats.
+
+
+</PRE><H3><a name="h3-X_Open-Curses">X/Open Curses</a></H3><PRE>
+ Refer to <EM>X/Open</EM> <EM>Curses,</EM> <EM>Issue</EM> <EM>7</EM> (2009).
+
+ X/Open's documentation for <EM>enhanced</EM> <EM>curses</EM> says only:
+
+ The <EM>getwin(</EM> <EM>)</EM> function reads window-related data stored
+ in the file by <EM>putwin(</EM> <EM>)</EM>. The function then creates
+ and initializes a new window using that data.
+
+ The <EM>putwin(</EM> <EM>)</EM> function writes all data associated with
+ <EM>win</EM> into the <EM>stdio</EM> stream to which <EM>filep</EM> points, using
+ an <STRONG>unspecified</STRONG> <STRONG>format</STRONG>. This information can be
+ retrieved later using <EM>getwin(</EM> <EM>)</EM>.
+
+ In the mid-1990s when the X/Open Curses document was writ-
+ ten, there were still systems using older, less capable
+ curses libraries (aside from the BSD curses library which
+ was not relevant to X/Open because it did not meet the
+ criteria for <EM>base</EM> <EM>curses</EM>). The document explained the
+ term "enhanced" as follows:
+
+ <STRONG>o</STRONG> Shading is used to identify <EM>X/Open</EM> <EM>Enhanced</EM> <EM>Curses</EM>
+ material, relating to interfaces included to pro-
+ vide enhanced capabilities for applications origi-
+ nally written to be compiled on systems based on
+ the UNIX operating system. Therefore, the features
+ described may not be present on systems that con-
+ form to <STRONG>XPG4</STRONG> <STRONG>or</STRONG> <STRONG>to</STRONG> <STRONG>earlier</STRONG> <STRONG>XPG</STRONG> <STRONG>releases</STRONG>. The rele-
+ vant reference pages may provide additional or more
+ specific portability warnings about use of the
+ material.
+
+ In the foregoing, emphasis was added to <STRONG>unspecified</STRONG> <STRONG>format</STRONG>
+ and to <STRONG>XPG4</STRONG> <STRONG>or</STRONG> <STRONG>to</STRONG> <STRONG>earlier</STRONG> <STRONG>XPG</STRONG> <STRONG>releases</STRONG>, for clarity.
+
+
+</PRE><H3><a name="h3-Unix-SystemV">Unix SystemV</a></H3><PRE>
+ Unix SystemV curses identified the file format by writing
+ a "magic number" at the beginning of the dump. The <STRONG>WINDOW</STRONG>
+ data and the lines of text follow, all in binary form.
+
+ The Solaris curses source has these definitions:
+
+ /* terminfo magic number */
+ #define MAGNUM 0432
+
+ /* curses screen dump magic number */
+ #define SVR2_DUMP_MAGIC_NUMBER 0433
+ #define SVR3_DUMP_MAGIC_NUMBER 0434
+
+ That is, the feature was likely introduced in SVr2 (1984),
+ and improved in SVr3 (1987). The Solaris curses source
+ has no magic number for SVr4 (1989). Other operating sys-
+ tems (AIX and HPUX) use a magic number which would corre-
+ spond to this definition:
+
+ /* curses screen dump magic number */
+ #define SVR4_DUMP_MAGIC_NUMBER 0435
+
+ That octal number in bytes is 001, 035. Because most Unix
+ vendors use big-endian hardware, the magic number is writ-
+ ten with the high-order byte first, e.g.,
+
+ 01 35
+
+ After the magic number, the <STRONG>WINDOW</STRONG> structure and line-data
+ are written in binary format. While the magic number used
+ by the Unix systems can be seen using <STRONG>od(1)</STRONG>, none of the
+ Unix systems documents the format used for screen-dumps.
+
+ The Unix systems do not use identical formats. While col-
+ lecting information for for this manual page, the <EM>save-</EM>
+ <EM>screen</EM> test-program produced dumps of different size (all
+ on 64-bit hardware, on 40x80 screens):
+
+ <STRONG>o</STRONG> AIX (51817 bytes)
+
+ <STRONG>o</STRONG> HPUX (90093 bytes)
+
+ <STRONG>o</STRONG> Solaris 10 (13273 bytes)
+
+ <STRONG>o</STRONG> ncurses5 (12888 bytes)
+
+
+</PRE><H3><a name="h3-Solaris">Solaris</a></H3><PRE>
+ As noted above, Solaris curses has no magic number corre-
+ sponding to SVr4 curses. This is odd since Solaris was
+ the first operating system to pass the SVr4 guidelines.
+ Solaris has two versions of curses:
+
+ <STRONG>o</STRONG> The default curses library uses the SVr3 magic number.
+
+ <STRONG>o</STRONG> There is an alternate curses library in <STRONG>/usr/xpg4</STRONG>.
+ This uses a textual format with no magic number.
+
+ According to the copyright notice, the <EM>xpg4</EM> Solaris
+ curses library was developed by MKS (Mortice Kern Sys-
+ tems) from 1990 to 1995.
+
+ Like ncurses6, there is a file-header with parameters.
+ Unlike ncurses6, the contents of the window are writ-
+ ten piecemeal, with coordinates and attributes for
+ each chunk of text rather than writing the whole win-
+ dow from top to bottom.
+
+
+</PRE><H3><a name="h3-PDCurses">PDCurses</a></H3><PRE>
+ PDCurses added support for screen dumps in version 2.7
+ (2005). Like Unix SystemV and ncurses5, it writes the
+ <STRONG>WINDOW</STRONG> structure in binary, but begins the file with its
+ three-byte identifier "PDC", followed by a one-byte ver-
+ sion, e.g.,
+
+ "PDC\001"
+
+
+</PRE><H3><a name="h3-NetBSD">NetBSD</a></H3><PRE>
+ As of April 2017, NetBSD curses does not yet support
+ screen dumps.
+
+
+</PRE><H2><a name="h2-EXAMPLE">EXAMPLE</a></H2><PRE>
+ Given a simple program which writes text to the screen
+ (and for the sake of example, limiting the screen-size to
+ 10x20):
+
+ #include <curses.h>
+
+ int
+ main(void)
+ {
+ putenv("LINES=10");
+ putenv("COLUMNS=20");
+ initscr();
+ start_color();
+ init_pair(1, COLOR_WHITE, COLOR_BLUE);
+ init_pair(2, COLOR_RED, COLOR_BLACK);
+ bkgd(<STRONG>COLOR_PAIR(1)</STRONG>);
+ move(4, 5);
+ attron(A_BOLD);
+ addstr("Hello");
+ move(5, 5);
+ attroff(A_BOLD);
+ attrset(A_REVERSE | <STRONG>COLOR_PAIR(2)</STRONG>);
+ addstr("World!");
+ refresh();
+ scr_dump("foo.out");
+ endwin();
+ return 0;
+ }
+
+ When run using ncurses6, the output looks like this:
+
+ \210\210\210\210ncurses 6.0.20170415
+ _cury=5
+ _curx=11
+ _maxy=9
+ _maxx=19
+ _flags=14
+ _attrs=\{REVERSE|C2}
+ flag=_idcok
+ _delay=-1
+ _regbottom=9
+ _bkgrnd=\{NORMAL|C1}\s
+ rows:
+ 1:\{NORMAL|C1}\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s
+ 2:\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s
+ 3:\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s
+ 4:\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s
+ 5:\s\s\s\s\s\{BOLD}Hello\{NORMAL}\s\s\s\s\s\s\s\s\s\s
+ 6:\s\s\s\s\s\{REVERSE|C2}World!\{NORMAL|C1}\s\s\s\s\s\s\s\s\s
+ 7:\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s
+ 8:\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s
+ 9:\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s
+ 10:\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s\s
+
+ The first four octal escapes are actually nonprinting
+ characters, while the remainder of the file is printable
+ text. You may notice:
+
+ <STRONG>o</STRONG> The actual color pair values are not written to the
+ file.
+
+ <STRONG>o</STRONG> All characters are shown in printable form; spaces are
+ "\s" to ensure they are not overlooked.
+
+ <STRONG>o</STRONG> Attributes are written in escaped curly braces, e.g.,
+ "\{BOLD}", and may include a color-pair (C1 or C2 in
+ this example).
+
+ <STRONG>o</STRONG> The parameters in the header are written out only if
+ they are nonzero. When reading back, order does not
+ matter.
+
+ Running the same program with Solaris <EM>xpg4</EM> curses gives
+ this dump:
+
+ MAX=10,20
+ BEG=0,0
+ SCROLL=0,10
+ VMIN=1
+ VTIME=0
+ FLAGS=0x1000
+ FG=0,0
+ BG=0,0,
+ 0,0,0,1,
+ 0,19,0,0,
+ 1,0,0,1,
+ 1,19,0,0,
+ 2,0,0,1,
+ 2,19,0,0,
+ 3,0,0,1,
+ 3,19,0,0,
+ 4,0,0,1,
+ 4,5,0x20,0,Hello
+ 4,10,0,1,
+ 4,19,0,0,
+ 5,0,0,1,
+ 5,5,0x4,2,World!
+ 5,11,0,1,
+ 5,19,0,0,
+ 6,0,0,1,
+ 6,19,0,0,
+ 7,0,0,1,
+ 7,19,0,0,
+ 8,0,0,1,
+ 8,19,0,0,
+ 9,0,0,1,
+ 9,19,0,0,
+ CUR=11,5
+
+ Solaris <STRONG>getwin</STRONG> requires that all parameters are present,
+ and in the same order. The <EM>xpg4</EM> curses library does not
+ know about the <STRONG>bce</STRONG> (back color erase) capability, and does
+ not color the window background.
+
+ On the other hand, the SVr4 curses library does know about
+ the background color. However, its screen dumps are in
+ binary. Here is the corresponding dump (using "od -t
+ x1"):
+
+ 0000000 1c 01 c3 d6 f3 58 05 00 0b 00 0a 00 14 00 00 00
+ 0000020 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
+ 0000040 00 00 b8 1a 06 08 cc 1a 06 08 00 00 09 00 10 00
+ 0000060 00 00 00 80 00 00 20 00 00 00 ff ff ff ff 00 00
+ 0000100 ff ff ff ff 00 00 00 00 20 80 00 00 20 80 00 00
+ 0000120 20 80 00 00 20 80 00 00 20 80 00 00 20 80 00 00
+ *
+ 0000620 20 80 00 00 20 80 00 00 20 80 00 00 48 80 00 04
+ 0000640 65 80 00 04 6c 80 00 04 6c 80 00 04 6f 80 00 04
+ 0000660 20 80 00 00 20 80 00 00 20 80 00 00 20 80 00 00
+ *
+ 0000740 20 80 00 00 20 80 00 00 20 80 00 00 57 00 81 00
+ 0000760 6f 00 81 00 72 00 81 00 6c 00 81 00 64 00 81 00
+ 0001000 21 00 81 00 20 80 00 00 20 80 00 00 20 80 00 00
+ 0001020 20 80 00 00 20 80 00 00 20 80 00 00 20 80 00 00
+ *
+ 0001540 20 80 00 00 20 80 00 00 00 00 f6 d1 01 00 f6 d1
+ 0001560 08 00 00 00 40 00 00 00 00 00 00 00 00 00 00 07
+ 0001600 00 04 00 01 00 01 00 00 00 01 00 00 00 00 00 00
+ 0001620 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+ *
+ 0002371
+
+
+</PRE><H2><a name="h2-SEE-ALSO">SEE ALSO</a></H2><PRE>
+ <STRONG><A HREF="curs_scr_dump.3x.html">curs_scr_dump(3x)</A></STRONG>, <STRONG><A HREF="curs_util.3x.html">curs_util(3x)</A></STRONG>.
+
+
+</PRE><H2><a name="h2-AUTHORS">AUTHORS</a></H2><PRE>
+ Thomas E. Dickey
+ extended screen-dump format for ncurses 6.0 (2015)
+
+ Eric S. Raymond
+ screen dump feature in ncurses 1.9.2d (1995)
+
+
+
+ <STRONG><A HREF="scr_dump.5.html">scr_dump(5)</A></STRONG>
+</PRE>
+<div class="nav">
+<ul>
+<li><a href="#h2-NAME">NAME</a></li>
+<li><a href="#h2-SYNOPSIS">SYNOPSIS</a></li>
+<li><a href="#h2-DESCRIPTION">DESCRIPTION</a>
+<ul>
+<li><a href="#h3-ncurses6">ncurses6</a></li>
+<li><a href="#h3-ncurses5-_legacy_">ncurses5 (legacy)</a></li>
+</ul>
+</li>
+<li><a href="#h2-PORTABILITY">PORTABILITY</a>
+<ul>
+<li><a href="#h3-X_Open-Curses">X/Open Curses</a></li>
+<li><a href="#h3-Unix-SystemV">Unix SystemV</a></li>
+<li><a href="#h3-Solaris">Solaris</a></li>
+<li><a href="#h3-PDCurses">PDCurses</a></li>
+<li><a href="#h3-NetBSD">NetBSD</a></li>
+</ul>
+</li>
+<li><a href="#h2-EXAMPLE">EXAMPLE</a></li>
+<li><a href="#h2-SEE-ALSO">SEE ALSO</a></li>
+<li><a href="#h2-AUTHORS">AUTHORS</a></li>
+</ul>
+</div>
+</BODY>
+</HTML>
</PRE><H2><a name="h2-SEE-ALSO">SEE ALSO</a></H2><PRE>
<STRONG><A HREF="tset.1.html">tset(1)</A></STRONG>, <STRONG><A HREF="infocmp.1m.html">infocmp(1m)</A></STRONG>, <STRONG><A HREF="ncurses.3x.html">curses(3x)</A></STRONG>, <STRONG><A HREF="terminfo.5.html">terminfo(5)</A></STRONG>.
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
* sale, use or other dealings in this Software without prior written *
* authorization. *
****************************************************************************
- * @Id: term_variables.3x,v 1.8 2017/01/07 19:25:15 tom Exp @
+ * @Id: term_variables.3x,v 1.9 2017/04/14 08:33:25 tom Exp @
-->
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01//EN">
<HTML>
</PRE><H3><a name="h3-Terminal-Type">Terminal Type</a></H3><PRE>
- On initialization of the curses or terminfo interfaces,
- <STRONG><A HREF="curs_terminfo.3x.html">setupterm(3x)</A></STRONG> copies the terminal name to the array <STRONG>tty-</STRONG>
- <STRONG>type</STRONG>.
+ A terminal description begins with one or more terminal
+ names separated by "|" (vertical bars). On initialization
+ of the curses or terminfo interfaces, <STRONG><A HREF="curs_terminfo.3x.html">setupterm(3x)</A></STRONG> copies
+ the terminal names to the array <STRONG>ttytype</STRONG>.
</PRE><H3><a name="h3-Terminfo-Names">Terminfo Names</a></H3><PRE>
In addition to the variables, <STRONG><term.h></STRONG> also defines a sym-
- bol for each terminfo capability <EM>long</EM> <EM>name</EM>. These are in
+ bol for each terminfo capability <EM>long</EM> <EM>name</EM>. These are in
terms of the symbol <STRONG>CUR</STRONG>, which is defined
- #define CUR cur_term->type.
+ #define CUR ((TERMTYPE *)(cur_term))->
These symbols provide a faster method of accessing termin-
fo capabilities than using <STRONG><A HREF="curs_terminfo.3x.html">tigetstr(3x)</A></STRONG>, etc.
+ The actual definition of <STRONG>CUR</STRONG> depends upon the implementa-
+ tion, but each terminfo library provides these long names
+ defined to point into the current terminal description
+ loaded into memory.
+
</PRE><H2><a name="h2-NOTES">NOTES</a></H2><PRE>
The low-level terminfo interface is initialized using
* sale, use or other dealings in this Software without prior written *
* authorization. *
****************************************************************************
- * @Id: terminfo.head,v 1.31 2017/03/06 09:58:14 tom Exp @
+ * @Id: terminfo.head,v 1.32 2017/04/22 13:52:49 tom Exp @
* Head of terminfo man page ends here
- * @Id: terminfo.tail,v 1.78 2017/03/04 23:52:35 tom Exp @
+ * @Id: terminfo.tail,v 1.84 2017/04/22 16:00:56 tom Exp @
* Beginning of terminfo.tail file
* This file is part of ncurses.
* See "terminfo.head" for copyright.
nals by giving a set of capabilities which they have, by
specifying how to perform screen operations, and by speci-
fying padding requirements and initialization sequences.
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
</PRE><H3><a name="h3-Terminfo-Entry-Syntax">Terminfo Entry Syntax</a></H3><PRE>
encounters a capability name which it does not recognize,
it infers its type (boolean, number or string) from the
syntax and makes an extended table entry for that capabil-
- ity. The <STRONG>use_extended_names</STRONG> function makes this informa-
- tion conditionally available to applications. The ncurses
- library provides the data leaving most of the behavior to
- applications:
+ ity. The <STRONG><A HREF="curs_extend.3x.html">use_extended_names(3x)</A></STRONG> function makes this
+ information conditionally available to applications. The
+ ncurses library provides the data leaving most of the
+ behavior to applications:
<STRONG>o</STRONG> User-defined capability strings whose name begins with
"k" are treated as function keys.
",".
A number of escape sequences are provided in the string
- valued capabilities for easy encoding of characters there.
- Both <STRONG>\E</STRONG> and <STRONG>\e</STRONG> map to an ESCAPE character, <STRONG>^x</STRONG> maps to a
- control-x for any appropriate x, and the sequences <STRONG>\n</STRONG> <STRONG>\l</STRONG>
- <STRONG>\r</STRONG> <STRONG>\t</STRONG> <STRONG>\b</STRONG> <STRONG>\f</STRONG> <STRONG>\s</STRONG> give a newline, line-feed, return, tab,
- backspace, form-feed, and space. Other escapes include
+ valued capabilities for easy encoding of characters there:
+
+ <STRONG>o</STRONG> Both <STRONG>\E</STRONG> and <STRONG>\e</STRONG> map to an ESCAPE character,
+
+ <STRONG>o</STRONG> <STRONG>^x</STRONG> maps to a control-x for any appropriate <EM>x</EM>, and
+
+ <STRONG>o</STRONG> the sequences
+
+ <STRONG>\n</STRONG>, <STRONG>\l</STRONG>, <STRONG>\r</STRONG>, <STRONG>\t</STRONG>, <STRONG>\b</STRONG>, <STRONG>\f</STRONG>, and <STRONG>\s</STRONG>
+
+ produce
+
+ <EM>newline</EM>, <EM>line-feed</EM>, <EM>return</EM>, <EM>tab</EM>, <EM>backspace</EM>, <EM>form-</EM>
+ <EM>feed</EM>, and <EM>space</EM>,
+
+ respectively.
+
+ X/Open Curses does not say what "appropriate <EM>x</EM>" might be.
+ In practice, that is a printable ASCII graphic character.
+ The special case "^?" is interpreted as DEL (127). In all
+ other cases, the character value is AND'd with 0x1f, map-
+ ping to ASCII control codes in the range 0 through 31.
+
+ Other escapes include
<STRONG>o</STRONG> <STRONG>\^</STRONG> for <STRONG>^</STRONG>,
<STRONG>o</STRONG> and <STRONG>\0</STRONG> for null.
- <STRONG>\0</STRONG> will produce \200, which does not terminate a
- string but behaves as a null character on most termi-
+ <STRONG>\0</STRONG> will produce \200, which does not terminate a
+ string but behaves as a null character on most termi-
nals, providing CS7 is specified. See <STRONG>stty(1)</STRONG>.
- The reason for this quirk is to maintain binary com-
- patibility of the compiled terminfo files with other
- implementations, e.g., the SVr4 systems, which docu-
- ment this. Compiled terminfo files use null-termi-
- nated strings, with no lengths. Modifying this would
+ The reason for this quirk is to maintain binary com-
+ patibility of the compiled terminfo files with other
+ implementations, e.g., the SVr4 systems, which docu-
+ ment this. Compiled terminfo files use null-termi-
+ nated strings, with no lengths. Modifying this would
require a new binary format, which would not work with
other implementations.
- Finally, characters may be given as three octal digits
+ Finally, characters may be given as three octal digits
after a <STRONG>\</STRONG>.
- A delay in milliseconds may appear anywhere in a string
- capability, enclosed in $<..> brackets, as in <STRONG>el</STRONG>=\EK$<5>,
- and padding characters are supplied by <STRONG><A HREF="curs_terminfo.3x.html">tputs(3x)</A></STRONG> to pro-
+ A delay in milliseconds may appear anywhere in a string
+ capability, enclosed in $<..> brackets, as in <STRONG>el</STRONG>=\EK$<5>,
+ and padding characters are supplied by <STRONG><A HREF="curs_terminfo.3x.html">tputs(3x)</A></STRONG> to pro-
vide this delay.
- <STRONG>o</STRONG> The delay must be a number with at most one decimal
+ <STRONG>o</STRONG> The delay must be a number with at most one decimal
place of precision; it may be followed by suffixes "*"
or "/" or both.
- <STRONG>o</STRONG> A "*" indicates that the padding required is propor-
- tional to the number of lines affected by the opera-
- tion, and the amount given is the per-affected-unit
- padding required. (In the case of insert character,
+ <STRONG>o</STRONG> A "*" indicates that the padding required is propor-
+ tional to the number of lines affected by the opera-
+ tion, and the amount given is the per-affected-unit
+ padding required. (In the case of insert character,
the factor is still the number of <EM>lines</EM> affected.)
- Normally, padding is advisory if the device has the
- <STRONG>xon</STRONG> capability; it is used for cost computation but
+ Normally, padding is advisory if the device has the
+ <STRONG>xon</STRONG> capability; it is used for cost computation but
does not trigger delays.
- <STRONG>o</STRONG> A "/" suffix indicates that the padding is mandatory
+ <STRONG>o</STRONG> A "/" suffix indicates that the padding is mandatory
and forces a delay of the given number of milliseconds
- even on devices for which <STRONG>xon</STRONG> is present to indicate
+ even on devices for which <STRONG>xon</STRONG> is present to indicate
flow control.
- Sometimes individual capabilities must be commented out.
- To do this, put a period before the capability name. For
+ Sometimes individual capabilities must be commented out.
+ To do this, put a period before the capability name. For
example, see the second <STRONG>ind</STRONG> in the example above.
</PRE><H3><a name="h3-Fetching-Compiled-Descriptions">Fetching Compiled Descriptions</a></H3><PRE>
- The <STRONG>ncurses</STRONG> library searches for terminal descriptions in
+ The <STRONG>ncurses</STRONG> library searches for terminal descriptions in
several places. It uses only the first description found.
- The library has a compiled-in list of places to search
- which can be overridden by environment variables. Before
- starting to search, <STRONG>ncurses</STRONG> eliminates duplicates in its
+ The library has a compiled-in list of places to search
+ which can be overridden by environment variables. Before
+ starting to search, <STRONG>ncurses</STRONG> eliminates duplicates in its
search list.
- <STRONG>o</STRONG> If the environment variable TERMINFO is set, it is
- interpreted as the pathname of a directory containing
- the compiled description you are working on. Only
+ <STRONG>o</STRONG> If the environment variable TERMINFO is set, it is
+ interpreted as the pathname of a directory containing
+ the compiled description you are working on. Only
that directory is searched.
- <STRONG>o</STRONG> If TERMINFO is not set, <STRONG>ncurses</STRONG> will instead look in
- the directory <STRONG>$HOME/.terminfo</STRONG> for a compiled descrip-
+ <STRONG>o</STRONG> If TERMINFO is not set, <STRONG>ncurses</STRONG> will instead look in
+ the directory <STRONG>$HOME/.terminfo</STRONG> for a compiled descrip-
tion.
- <STRONG>o</STRONG> Next, if the environment variable TERMINFO_DIRS is
+ <STRONG>o</STRONG> Next, if the environment variable TERMINFO_DIRS is
set, <STRONG>ncurses</STRONG> will interpret the contents of that vari-
- able as a list of colon-separated directories (or
+ able as a list of colon-separated directories (or
database files) to be searched.
- An empty directory name (i.e., if the variable begins
- or ends with a colon, or contains adjacent colons) is
- interpreted as the system location <EM>/usr/share/ter-</EM>
+ An empty directory name (i.e., if the variable begins
+ or ends with a colon, or contains adjacent colons) is
+ interpreted as the system location <EM>/usr/share/ter-</EM>
<EM>minfo</EM>.
<STRONG>o</STRONG> Finally, <STRONG>ncurses</STRONG> searches these compiled-in locations:
- <STRONG>o</STRONG> a list of directories
+ <STRONG>o</STRONG> a list of directories
(/usr/local/ncurses/share/terminfo:/usr/share/ter-
minfo), and
</PRE><H3><a name="h3-Preparing-Descriptions">Preparing Descriptions</a></H3><PRE>
- We now outline how to prepare descriptions of terminals.
- The most effective way to prepare a terminal description
- is by imitating the description of a similar terminal in
- <EM>terminfo</EM> and to build up a description gradually, using
+ We now outline how to prepare descriptions of terminals.
+ The most effective way to prepare a terminal description
+ is by imitating the description of a similar terminal in
+ <EM>terminfo</EM> and to build up a description gradually, using
partial descriptions with <EM>vi</EM> or some other screen-oriented
- program to check that they are correct. Be aware that a
+ program to check that they are correct. Be aware that a
very unusual terminal may expose deficiencies in the abil-
- ity of the <EM>terminfo</EM> file to describe it or bugs in the
+ ity of the <EM>terminfo</EM> file to describe it or bugs in the
screen-handling code of the test program.
- To get the padding for insert line right (if the terminal
+ To get the padding for insert line right (if the terminal
manufacturer did not document it) a severe test is to edit
- a large file at 9600 baud, delete 16 or so lines from the
- middle of the screen, then hit the "u" key several times
- quickly. If the terminal messes up, more padding is usu-
- ally needed. A similar test can be used for insert char-
+ a large file at 9600 baud, delete 16 or so lines from the
+ middle of the screen, then hit the "u" key several times
+ quickly. If the terminal messes up, more padding is usu-
+ ally needed. A similar test can be used for insert char-
acter.
</PRE><H3><a name="h3-Basic-Capabilities">Basic Capabilities</a></H3><PRE>
- The number of columns on each line for the terminal is
- given by the <STRONG>cols</STRONG> numeric capability. If the terminal is
- a CRT, then the number of lines on the screen is given by
+ The number of columns on each line for the terminal is
+ given by the <STRONG>cols</STRONG> numeric capability. If the terminal is
+ a CRT, then the number of lines on the screen is given by
the <STRONG>lines</STRONG> capability. If the terminal wraps around to the
- beginning of the next line when it reaches the right mar-
+ beginning of the next line when it reaches the right mar-
gin, then it should have the <STRONG>am</STRONG> capability. If the termi-
- nal can clear its screen, leaving the cursor in the home
- position, then this is given by the <STRONG>clear</STRONG> string capabil-
- ity. If the terminal overstrikes (rather than clearing a
- position when a character is struck over) then it should
- have the <STRONG>os</STRONG> capability. If the terminal is a printing
- terminal, with no soft copy unit, give it both <STRONG>hc</STRONG> and <STRONG>os</STRONG>.
- (<STRONG>os</STRONG> applies to storage scope terminals, such as TEKTRONIX
- 4010 series, as well as hard copy and APL terminals.) If
+ nal can clear its screen, leaving the cursor in the home
+ position, then this is given by the <STRONG>clear</STRONG> string capabil-
+ ity. If the terminal overstrikes (rather than clearing a
+ position when a character is struck over) then it should
+ have the <STRONG>os</STRONG> capability. If the terminal is a printing
+ terminal, with no soft copy unit, give it both <STRONG>hc</STRONG> and <STRONG>os</STRONG>.
+ (<STRONG>os</STRONG> applies to storage scope terminals, such as TEKTRONIX
+ 4010 series, as well as hard copy and APL terminals.) If
there is a code to move the cursor to the left edge of the
current row, give this as <STRONG>cr</STRONG>. (Normally this will be car-
- riage return, control M.) If there is a code to produce
+ riage return, control M.) If there is a code to produce
an audible signal (bell, beep, etc) give this as <STRONG>bel</STRONG>.
- If there is a code to move the cursor one position to the
- left (such as backspace) that capability should be given
- as <STRONG>cub1</STRONG>. Similarly, codes to move to the right, up, and
+ If there is a code to move the cursor one position to the
+ left (such as backspace) that capability should be given
+ as <STRONG>cub1</STRONG>. Similarly, codes to move to the right, up, and
down should be given as <STRONG>cuf1</STRONG>, <STRONG>cuu1</STRONG>, and <STRONG>cud1</STRONG>. These local
- cursor motions should not alter the text they pass over,
- for example, you would not normally use "<STRONG>cuf1</STRONG>= " because
+ cursor motions should not alter the text they pass over,
+ for example, you would not normally use "<STRONG>cuf1</STRONG>= " because
the space would erase the character moved over.
- A very important point here is that the local cursor
- motions encoded in <EM>terminfo</EM> are undefined at the left and
- top edges of a CRT terminal. Programs should never
- attempt to backspace around the left edge, unless <STRONG>bw</STRONG> is
+ A very important point here is that the local cursor
+ motions encoded in <EM>terminfo</EM> are undefined at the left and
+ top edges of a CRT terminal. Programs should never
+ attempt to backspace around the left edge, unless <STRONG>bw</STRONG> is
given, and never attempt to go up locally off the top. In
- order to scroll text up, a program will go to the bottom
+ order to scroll text up, a program will go to the bottom
left corner of the screen and send the <STRONG>ind</STRONG> (index) string.
To scroll text down, a program goes to the top left corner
- of the screen and sends the <STRONG>ri</STRONG> (reverse index) string.
- The strings <STRONG>ind</STRONG> and <STRONG>ri</STRONG> are undefined when not on their
+ of the screen and sends the <STRONG>ri</STRONG> (reverse index) string.
+ The strings <STRONG>ind</STRONG> and <STRONG>ri</STRONG> are undefined when not on their
respective corners of the screen.
Parameterized versions of the scrolling sequences are <STRONG>indn</STRONG>
and <STRONG>rin</STRONG> which have the same semantics as <STRONG>ind</STRONG> and <STRONG>ri</STRONG> except
- that they take one parameter, and scroll that many lines.
- They are also undefined except at the appropriate edge of
+ that they take one parameter, and scroll that many lines.
+ They are also undefined except at the appropriate edge of
the screen.
- The <STRONG>am</STRONG> capability tells whether the cursor sticks at the
- right edge of the screen when text is output, but this
+ The <STRONG>am</STRONG> capability tells whether the cursor sticks at the
+ right edge of the screen when text is output, but this
does not necessarily apply to a <STRONG>cuf1</STRONG> from the last column.
- The only local motion which is defined from the left edge
- is if <STRONG>bw</STRONG> is given, then a <STRONG>cub1</STRONG> from the left edge will
- move to the right edge of the previous row. If <STRONG>bw</STRONG> is not
- given, the effect is undefined. This is useful for draw-
- ing a box around the edge of the screen, for example. If
- the terminal has switch selectable automatic margins, the
- <EM>terminfo</EM> file usually assumes that this is on; i.e., <STRONG>am</STRONG>.
- If the terminal has a command which moves to the first
- column of the next line, that command can be given as <STRONG>nel</STRONG>
- (newline). It does not matter if the command clears the
- remainder of the current line, so if the terminal has no
- <STRONG>cr</STRONG> and <STRONG>lf</STRONG> it may still be possible to craft a working <STRONG>nel</STRONG>
+ The only local motion which is defined from the left edge
+ is if <STRONG>bw</STRONG> is given, then a <STRONG>cub1</STRONG> from the left edge will
+ move to the right edge of the previous row. If <STRONG>bw</STRONG> is not
+ given, the effect is undefined. This is useful for draw-
+ ing a box around the edge of the screen, for example. If
+ the terminal has switch selectable automatic margins, the
+ <EM>terminfo</EM> file usually assumes that this is on; i.e., <STRONG>am</STRONG>.
+ If the terminal has a command which moves to the first
+ column of the next line, that command can be given as <STRONG>nel</STRONG>
+ (newline). It does not matter if the command clears the
+ remainder of the current line, so if the terminal has no
+ <STRONG>cr</STRONG> and <STRONG>lf</STRONG> it may still be possible to craft a working <STRONG>nel</STRONG>
out of one or both of them.
These capabilities suffice to describe hard-copy and
- "glass-tty" terminals. Thus the model 33 teletype is
+ "glass-tty" terminals. Thus the model 33 teletype is
described as
33|tty33|tty|model 33 teletype,
</PRE><H3><a name="h3-Parameterized-Strings">Parameterized Strings</a></H3><PRE>
- Cursor addressing and other strings requiring parameters
- in the terminal are described by a parameterized string
- capability, with <EM>printf</EM>-like escapes such as <EM>%x</EM> in it.
- For example, to address the cursor, the <STRONG>cup</STRONG> capability is
+ Cursor addressing and other strings requiring parameters
+ in the terminal are described by a parameterized string
+ capability, with <EM>printf</EM>-like escapes such as <EM>%x</EM> in it.
+ For example, to address the cursor, the <STRONG>cup</STRONG> capability is
given, using two parameters: the row and column to address
to. (Rows and columns are numbered from zero and refer to
the physical screen visible to the user, not to any unseen
- memory.) If the terminal has memory relative cursor
+ memory.) If the terminal has memory relative cursor
addressing, that can be indicated by <STRONG>mrcup</STRONG>.
- The parameter mechanism uses a stack and special <STRONG>%</STRONG> codes
- to manipulate it. Typically a sequence will push one of
- the parameters onto the stack and then print it in some
- format. Print (e.g., "%d") is a special case. Other
- operations, including "%t" pop their operand from the
+ The parameter mechanism uses a stack and special <STRONG>%</STRONG> codes
+ to manipulate it. Typically a sequence will push one of
+ the parameters onto the stack and then print it in some
+ format. Print (e.g., "%d") is a special case. Other
+ operations, including "%t" pop their operand from the
stack. It is noted that more complex operations are often
necessary, e.g., in the <STRONG>sgr</STRONG> string.
<STRONG>%%</STRONG> outputs "%"
<STRONG>%</STRONG><EM>[[</EM>:<EM>]flags][width[.precision]][</EM><STRONG>doxXs</STRONG><EM>]</EM>
- as in <STRONG>printf</STRONG>, flags are <EM>[-+#]</EM> and <EM>space</EM>. Use a ":"
- to allow the next character to be a "-" flag, avoid-
+ as in <STRONG>printf</STRONG>, flags are <EM>[-+#]</EM> and <EM>space</EM>. Use a ":"
+ to allow the next character to be a "-" flag, avoid-
ing interpreting "%-" as an operator.
%c print <EM>pop()</EM> like %c in <STRONG>printf</STRONG>
<STRONG>%g</STRONG><EM>[A-Z]</EM>
get static variable <EM>[a-z]</EM> and push it
- The terms "static" and "dynamic" are misleading.
- Historically, these are simply two different sets of
- variables, whose values are not reset between calls
- to <STRONG><A HREF="curs_terminfo.3x.html">tparm(3x)</A></STRONG>. However, that fact is not documented
- in other implementations. Relying on it will
- adversely impact portability to other implementa-
+ The terms "static" and "dynamic" are misleading.
+ Historically, these are simply two different sets of
+ variables, whose values are not reset between calls
+ to <STRONG><A HREF="curs_terminfo.3x.html">tparm(3x)</A></STRONG>. However, that fact is not documented
+ in other implementations. Relying on it will
+ adversely impact portability to other implementa-
tions.
<STRONG>%'</STRONG><EM>c</EM><STRONG>'</STRONG> char constant <EM>c</EM>
logical AND and OR operations (for conditionals)
<STRONG>%!</STRONG>, <STRONG>%~</STRONG>
- unary operations (logical and bit complement):
+ unary operations (logical and bit complement):
<EM>push(op</EM> <EM>pop())</EM>
<STRONG>%i</STRONG> add 1 to first two parameters (for ANSI terminals)
<STRONG>%?</STRONG> <EM>expr</EM> <STRONG>%t</STRONG> <EM>thenpart</EM> <STRONG>%e</STRONG> <EM>elsepart</EM> <STRONG>%;</STRONG>
- This forms an if-then-else. The <STRONG>%e</STRONG> <EM>elsepart</EM> is
- optional. Usually the <STRONG>%?</STRONG> <EM>expr</EM> part pushes a value
- onto the stack, and <STRONG>%t</STRONG> pops it from the stack, test-
- ing if it is nonzero (true). If it is zero (false),
+ This forms an if-then-else. The <STRONG>%e</STRONG> <EM>elsepart</EM> is
+ optional. Usually the <STRONG>%?</STRONG> <EM>expr</EM> part pushes a value
+ onto the stack, and <STRONG>%t</STRONG> pops it from the stack, test-
+ ing if it is nonzero (true). If it is zero (false),
control passes to the <STRONG>%e</STRONG> (else) part.
It is possible to form else-if's a la Algol 68:
where ci are conditions, bi are bodies.
Use the <STRONG>-f</STRONG> option of <STRONG>tic</STRONG> or <STRONG>infocmp</STRONG> to see the struc-
- ture of if-then-else's. Some strings, e.g., <STRONG>sgr</STRONG> can
+ ture of if-then-else's. Some strings, e.g., <STRONG>sgr</STRONG> can
be very complicated when written on one line. The <STRONG>-f</STRONG>
- option splits the string into lines with the parts
+ option splits the string into lines with the parts
indented.
Binary operations are in postfix form with the operands in
- the usual order. That is, to get x-5 one would use
- "%gx%{5}%-". <STRONG>%P</STRONG> and <STRONG>%g</STRONG> variables are persistent across
+ the usual order. That is, to get x-5 one would use
+ "%gx%{5}%-". <STRONG>%P</STRONG> and <STRONG>%g</STRONG> variables are persistent across
escape-string evaluations.
Consider the HP2645, which, to get to row 3 and column 12,
- needs to be sent \E&a12c03Y padded for 6 milliseconds.
- Note that the order of the rows and columns is inverted
- here, and that the row and column are printed as two dig-
+ needs to be sent \E&a12c03Y padded for 6 milliseconds.
+ Note that the order of the rows and columns is inverted
+ here, and that the row and column are printed as two dig-
its. Thus its <STRONG>cup</STRONG> capability is "cup=6\E&%p2%2dc%p1%2dY".
The Microterm ACT-IV needs the current row and column sent
- preceded by a <STRONG>^T</STRONG>, with the row and column simply encoded
- in binary, "cup=^T%p1%c%p2%c". Terminals which use "%c"
- need to be able to backspace the cursor (<STRONG>cub1</STRONG>), and to
+ preceded by a <STRONG>^T</STRONG>, with the row and column simply encoded
+ in binary, "cup=^T%p1%c%p2%c". Terminals which use "%c"
+ need to be able to backspace the cursor (<STRONG>cub1</STRONG>), and to
move the cursor up one line on the screen (<STRONG>cuu1</STRONG>). This is
- necessary because it is not always safe to transmit <STRONG>\n</STRONG> <STRONG>^D</STRONG>
- and <STRONG>\r</STRONG>, as the system may change or discard them. (The
- library routines dealing with terminfo set tty modes so
+ necessary because it is not always safe to transmit <STRONG>\n</STRONG> <STRONG>^D</STRONG>
+ and <STRONG>\r</STRONG>, as the system may change or discard them. (The
+ library routines dealing with terminfo set tty modes so
that tabs are never expanded, so \t is safe to send. This
turns out to be essential for the Ann Arbor 4080.)
A final example is the LSI ADM-3a, which uses row and col-
umn offset by a blank character, thus "cup=\E=%p1%'
- '%+%c%p2%' '%+%c". After sending "\E=", this pushes the
- first parameter, pushes the ASCII value for a space (32),
- adds them (pushing the sum on the stack in place of the
- two previous values) and outputs that value as a charac-
- ter. Then the same is done for the second parameter.
+ '%+%c%p2%' '%+%c". After sending "\E=", this pushes the
+ first parameter, pushes the ASCII value for a space (32),
+ adds them (pushing the sum on the stack in place of the
+ two previous values) and outputs that value as a charac-
+ ter. Then the same is done for the second parameter.
More complex arithmetic is possible using the stack.
</PRE><H3><a name="h3-Cursor-Motions">Cursor Motions</a></H3><PRE>
If the terminal has a fast way to home the cursor (to very
- upper left corner of screen) then this can be given as
- <STRONG>home</STRONG>; similarly a fast way of getting to the lower left-
- hand corner can be given as <STRONG>ll</STRONG>; this may involve going up
- with <STRONG>cuu1</STRONG> from the home position, but a program should
- never do this itself (unless <STRONG>ll</STRONG> does) because it can make
- no assumption about the effect of moving up from the home
- position. Note that the home position is the same as
+ upper left corner of screen) then this can be given as
+ <STRONG>home</STRONG>; similarly a fast way of getting to the lower left-
+ hand corner can be given as <STRONG>ll</STRONG>; this may involve going up
+ with <STRONG>cuu1</STRONG> from the home position, but a program should
+ never do this itself (unless <STRONG>ll</STRONG> does) because it can make
+ no assumption about the effect of moving up from the home
+ position. Note that the home position is the same as
addressing to (0,0): to the top left corner of the screen,
- not of memory. (Thus, the \EH sequence on HP terminals
+ not of memory. (Thus, the \EH sequence on HP terminals
cannot be used for <STRONG>home</STRONG>.)
If the terminal has row or column absolute cursor address-
- ing, these can be given as single parameter capabilities
+ ing, these can be given as single parameter capabilities
<STRONG>hpa</STRONG> (horizontal position absolute) and <STRONG>vpa</STRONG> (vertical posi-
tion absolute). Sometimes these are shorter than the more
- general two parameter sequence (as with the hp2645) and
+ general two parameter sequence (as with the hp2645) and
can be used in preference to <STRONG>cup</STRONG>. If there are parameter-
- ized local motions (e.g., move <EM>n</EM> spaces to the right)
+ ized local motions (e.g., move <EM>n</EM> spaces to the right)
these can be given as <STRONG>cud</STRONG>, <STRONG>cub</STRONG>, <STRONG>cuf</STRONG>, and <STRONG>cuu</STRONG> with a single
- parameter indicating how many spaces to move. These are
- primarily useful if the terminal does not have <STRONG>cup</STRONG>, such
+ parameter indicating how many spaces to move. These are
+ primarily useful if the terminal does not have <STRONG>cup</STRONG>, such
as the TEKTRONIX 4025.
If the terminal needs to be in a special mode when running
a program that uses these capabilities, the codes to enter
- and exit this mode can be given as <STRONG>smcup</STRONG> and <STRONG>rmcup</STRONG>. This
- arises, for example, from terminals like the Concept with
- more than one page of memory. If the terminal has only
- memory relative cursor addressing and not screen relative
+ and exit this mode can be given as <STRONG>smcup</STRONG> and <STRONG>rmcup</STRONG>. This
+ arises, for example, from terminals like the Concept with
+ more than one page of memory. If the terminal has only
+ memory relative cursor addressing and not screen relative
cursor addressing, a one screen-sized window must be fixed
- into the terminal for cursor addressing to work properly.
+ into the terminal for cursor addressing to work properly.
This is also used for the TEKTRONIX 4025, where <STRONG>smcup</STRONG> sets
- the command character to be the one used by terminfo. If
- the <STRONG>smcup</STRONG> sequence will not restore the screen after an
+ the command character to be the one used by terminfo. If
+ the <STRONG>smcup</STRONG> sequence will not restore the screen after an
<STRONG>rmcup</STRONG> sequence is output (to the state prior to outputting
<STRONG>rmcup</STRONG>), specify <STRONG>nrrmc</STRONG>.
</PRE><H3><a name="h3-Area-Clears">Area Clears</a></H3><PRE>
If the terminal can clear from the current position to the
- end of the line, leaving the cursor where it is, this
+ end of the line, leaving the cursor where it is, this
should be given as <STRONG>el</STRONG>. If the terminal can clear from the
- beginning of the line to the current position inclusive,
- leaving the cursor where it is, this should be given as
- <STRONG>el1</STRONG>. If the terminal can clear from the current position
- to the end of the display, then this should be given as
- <STRONG>ed</STRONG>. <STRONG>Ed</STRONG> is only defined from the first column of a line.
- (Thus, it can be simulated by a request to delete a large
+ beginning of the line to the current position inclusive,
+ leaving the cursor where it is, this should be given as
+ <STRONG>el1</STRONG>. If the terminal can clear from the current position
+ to the end of the display, then this should be given as
+ <STRONG>ed</STRONG>. <STRONG>Ed</STRONG> is only defined from the first column of a line.
+ (Thus, it can be simulated by a request to delete a large
number of lines, if a true <STRONG>ed</STRONG> is not available.)
</PRE><H3><a name="h3-Insert_delete-line-and-vertical-motions">Insert/delete line and vertical motions</a></H3><PRE>
- If the terminal can open a new blank line before the line
- where the cursor is, this should be given as <STRONG>il1</STRONG>; this is
- done only from the first position of a line. The cursor
+ If the terminal can open a new blank line before the line
+ where the cursor is, this should be given as <STRONG>il1</STRONG>; this is
+ done only from the first position of a line. The cursor
must then appear on the newly blank line. If the terminal
- can delete the line which the cursor is on, then this
- should be given as <STRONG>dl1</STRONG>; this is done only from the first
- position on the line to be deleted. Versions of <STRONG>il1</STRONG> and
- <STRONG>dl1</STRONG> which take a single parameter and insert or delete
+ can delete the line which the cursor is on, then this
+ should be given as <STRONG>dl1</STRONG>; this is done only from the first
+ position on the line to be deleted. Versions of <STRONG>il1</STRONG> and
+ <STRONG>dl1</STRONG> which take a single parameter and insert or delete
that many lines can be given as <STRONG>il</STRONG> and <STRONG>dl</STRONG>.
- If the terminal has a settable scrolling region (like the
- vt100) the command to set this can be described with the
- <STRONG>csr</STRONG> capability, which takes two parameters: the top and
+ If the terminal has a settable scrolling region (like the
+ vt100) the command to set this can be described with the
+ <STRONG>csr</STRONG> capability, which takes two parameters: the top and
bottom lines of the scrolling region. The cursor position
is, alas, undefined after using this command.
- It is possible to get the effect of insert or delete line
+ It is possible to get the effect of insert or delete line
using <STRONG>csr</STRONG> on a properly chosen region; the <STRONG>sc</STRONG> and <STRONG>rc</STRONG> (save
- and restore cursor) commands may be useful for ensuring
- that your synthesized insert/delete string does not move
- the cursor. (Note that the <STRONG><A HREF="ncurses.3x.html">ncurses(3x)</A></STRONG> library does this
- synthesis automatically, so you need not compose
+ and restore cursor) commands may be useful for ensuring
+ that your synthesized insert/delete string does not move
+ the cursor. (Note that the <STRONG><A HREF="ncurses.3x.html">ncurses(3x)</A></STRONG> library does this
+ synthesis automatically, so you need not compose
insert/delete strings for an entry with <STRONG>csr</STRONG>).
Yet another way to construct insert and delete might be to
- use a combination of index with the memory-lock feature
- found on some terminals (like the HP-700/90 series, which
+ use a combination of index with the memory-lock feature
+ found on some terminals (like the HP-700/90 series, which
however also has insert/delete).
- Inserting lines at the top or bottom of the screen can
- also be done using <STRONG>ri</STRONG> or <STRONG>ind</STRONG> on many terminals without a
- true insert/delete line, and is often faster even on ter-
+ Inserting lines at the top or bottom of the screen can
+ also be done using <STRONG>ri</STRONG> or <STRONG>ind</STRONG> on many terminals without a
+ true insert/delete line, and is often faster even on ter-
minals with those features.
- The boolean <STRONG>non_dest_scroll_region</STRONG> should be set if each
- scrolling window is effectively a view port on a screen-
- sized canvas. To test for this capability, create a
- scrolling region in the middle of the screen, write some-
- thing to the bottom line, move the cursor to the top of
+ The boolean <STRONG>non_dest_scroll_region</STRONG> should be set if each
+ scrolling window is effectively a view port on a screen-
+ sized canvas. To test for this capability, create a
+ scrolling region in the middle of the screen, write some-
+ thing to the bottom line, move the cursor to the top of
the region, and do <STRONG>ri</STRONG> followed by <STRONG>dl1</STRONG> or <STRONG>ind</STRONG>. If the data
- scrolled off the bottom of the region by the <STRONG>ri</STRONG> re-
- appears, then scrolling is non-destructive. System V and
- XSI Curses expect that <STRONG>ind</STRONG>, <STRONG>ri</STRONG>, <STRONG>indn</STRONG>, and <STRONG>rin</STRONG> will simu-
- late destructive scrolling; their documentation cautions
- you not to define <STRONG>csr</STRONG> unless this is true. This <STRONG>curses</STRONG>
+ scrolled off the bottom of the region by the <STRONG>ri</STRONG> re-
+ appears, then scrolling is non-destructive. System V and
+ XSI Curses expect that <STRONG>ind</STRONG>, <STRONG>ri</STRONG>, <STRONG>indn</STRONG>, and <STRONG>rin</STRONG> will simu-
+ late destructive scrolling; their documentation cautions
+ you not to define <STRONG>csr</STRONG> unless this is true. This <STRONG>curses</STRONG>
implementation is more liberal and will do explicit erases
after scrolling if <STRONG>ndsrc</STRONG> is defined.
If the terminal has the ability to define a window as part
- of memory, which all commands affect, it should be given
+ of memory, which all commands affect, it should be given
as the parameterized string <STRONG>wind</STRONG>. The four parameters are
- the starting and ending lines in memory and the starting
+ the starting and ending lines in memory and the starting
and ending columns in memory, in that order.
- If the terminal can retain display memory above, then the
- <STRONG>da</STRONG> capability should be given; if display memory can be
- retained below, then <STRONG>db</STRONG> should be given. These indicate
- that deleting a line or scrolling may bring non-blank
- lines up from below or that scrolling back with <STRONG>ri</STRONG> may
+ If the terminal can retain display memory above, then the
+ <STRONG>da</STRONG> capability should be given; if display memory can be
+ retained below, then <STRONG>db</STRONG> should be given. These indicate
+ that deleting a line or scrolling may bring non-blank
+ lines up from below or that scrolling back with <STRONG>ri</STRONG> may
bring down non-blank lines.
</PRE><H3><a name="h3-Insert_Delete-Character">Insert/Delete Character</a></H3><PRE>
- There are two basic kinds of intelligent terminals with
- respect to insert/delete character which can be described
- using <EM>terminfo.</EM> The most common insert/delete character
- operations affect only the characters on the current line
- and shift characters off the end of the line rigidly.
- Other terminals, such as the Concept 100 and the Perkin
- Elmer Owl, make a distinction between typed and untyped
- blanks on the screen, shifting upon an insert or delete
- only to an untyped blank on the screen which is either
+ There are two basic kinds of intelligent terminals with
+ respect to insert/delete character which can be described
+ using <EM>terminfo.</EM> The most common insert/delete character
+ operations affect only the characters on the current line
+ and shift characters off the end of the line rigidly.
+ Other terminals, such as the Concept 100 and the Perkin
+ Elmer Owl, make a distinction between typed and untyped
+ blanks on the screen, shifting upon an insert or delete
+ only to an untyped blank on the screen which is either
eliminated, or expanded to two untyped blanks.
- You can determine the kind of terminal you have by clear-
- ing the screen and then typing text separated by cursor
- motions. Type "abc def" using local cursor motions
- (not spaces) between the "abc" and the "def". Then posi-
- tion the cursor before the "abc" and put the terminal in
- insert mode. If typing characters causes the rest of the
- line to shift rigidly and characters to fall off the end,
+ You can determine the kind of terminal you have by clear-
+ ing the screen and then typing text separated by cursor
+ motions. Type "abc def" using local cursor motions
+ (not spaces) between the "abc" and the "def". Then posi-
+ tion the cursor before the "abc" and put the terminal in
+ insert mode. If typing characters causes the rest of the
+ line to shift rigidly and characters to fall off the end,
then your terminal does not distinguish between blanks and
- untyped positions. If the "abc" shifts over to the "def"
- which then move together around the end of the current
- line and onto the next as you insert, you have the second
+ untyped positions. If the "abc" shifts over to the "def"
+ which then move together around the end of the current
+ line and onto the next as you insert, you have the second
type of terminal, and should give the capability <STRONG>in</STRONG>, which
stands for "insert null".
- While these are two logically separate attributes (one
- line versus multi-line insert mode, and special treatment
- of untyped spaces) we have seen no terminals whose insert
+ While these are two logically separate attributes (one
+ line versus multi-line insert mode, and special treatment
+ of untyped spaces) we have seen no terminals whose insert
mode cannot be described with the single attribute.
- Terminfo can describe both terminals which have an insert
+ Terminfo can describe both terminals which have an insert
mode, and terminals which send a simple sequence to open a
- blank position on the current line. Give as <STRONG>smir</STRONG> the
- sequence to get into insert mode. Give as <STRONG>rmir</STRONG> the
- sequence to leave insert mode. Now give as <STRONG>ich1</STRONG> any
+ blank position on the current line. Give as <STRONG>smir</STRONG> the
+ sequence to get into insert mode. Give as <STRONG>rmir</STRONG> the
+ sequence to leave insert mode. Now give as <STRONG>ich1</STRONG> any
sequence needed to be sent just before sending the charac-
- ter to be inserted. Most terminals with a true insert
- mode will not give <STRONG>ich1</STRONG>; terminals which send a sequence
+ ter to be inserted. Most terminals with a true insert
+ mode will not give <STRONG>ich1</STRONG>; terminals which send a sequence
to open a screen position should give it here.
- If your terminal has both, insert mode is usually prefer-
- able to <STRONG>ich1</STRONG>. Technically, you should not give both
- unless the terminal actually requires both to be used in
- combination. Accordingly, some non-curses applications
- get confused if both are present; the symptom is doubled
+ If your terminal has both, insert mode is usually prefer-
+ able to <STRONG>ich1</STRONG>. Technically, you should not give both
+ unless the terminal actually requires both to be used in
+ combination. Accordingly, some non-curses applications
+ get confused if both are present; the symptom is doubled
characters in an update using insert. This requirement is
now rare; most <STRONG>ich</STRONG> sequences do not require previous smir,
and most smir insert modes do not require <STRONG>ich1</STRONG> before each
- character. Therefore, the new <STRONG>curses</STRONG> actually assumes
- this is the case and uses either <STRONG>rmir</STRONG>/<STRONG>smir</STRONG> or <STRONG>ich</STRONG>/<STRONG>ich1</STRONG> as
+ character. Therefore, the new <STRONG>curses</STRONG> actually assumes
+ this is the case and uses either <STRONG>rmir</STRONG>/<STRONG>smir</STRONG> or <STRONG>ich</STRONG>/<STRONG>ich1</STRONG> as
appropriate (but not both). If you have to write an entry
- to be used under new curses for a terminal old enough to
+ to be used under new curses for a terminal old enough to
need both, include the <STRONG>rmir</STRONG>/<STRONG>smir</STRONG> sequences in <STRONG>ich1</STRONG>.
If post insert padding is needed, give this as a number of
- milliseconds in <STRONG>ip</STRONG> (a string option). Any other sequence
- which may need to be sent after an insert of a single
+ milliseconds in <STRONG>ip</STRONG> (a string option). Any other sequence
+ which may need to be sent after an insert of a single
character may also be given in <STRONG>ip</STRONG>. If your terminal needs
both to be placed into an "insert mode" and a special code
- to precede each inserted character, then both <STRONG>smir</STRONG>/<STRONG>rmir</STRONG>
- and <STRONG>ich1</STRONG> can be given, and both will be used. The <STRONG>ich</STRONG>
+ to precede each inserted character, then both <STRONG>smir</STRONG>/<STRONG>rmir</STRONG>
+ and <STRONG>ich1</STRONG> can be given, and both will be used. The <STRONG>ich</STRONG>
capability, with one parameter, <EM>n</EM>, will repeat the effects
of <STRONG>ich1</STRONG> <EM>n</EM> times.
in insert mode, give this as a number of milliseconds pad-
ding in <STRONG>rmp</STRONG>.
- It is occasionally necessary to move around while in
- insert mode to delete characters on the same line (e.g.,
- if there is a tab after the insertion position). If your
- terminal allows motion while in insert mode you can give
- the capability <STRONG>mir</STRONG> to speed up inserting in this case.
- Omitting <STRONG>mir</STRONG> will affect only speed. Some terminals
+ It is occasionally necessary to move around while in
+ insert mode to delete characters on the same line (e.g.,
+ if there is a tab after the insertion position). If your
+ terminal allows motion while in insert mode you can give
+ the capability <STRONG>mir</STRONG> to speed up inserting in this case.
+ Omitting <STRONG>mir</STRONG> will affect only speed. Some terminals
(notably Datamedia's) must not have <STRONG>mir</STRONG> because of the way
their insert mode works.
- Finally, you can specify <STRONG>dch1</STRONG> to delete a single charac-
- ter, <STRONG>dch</STRONG> with one parameter, <EM>n</EM>, to delete <EM>n</EM> <EM>characters,</EM>
- and delete mode by giving <STRONG>smdc</STRONG> and <STRONG>rmdc</STRONG> to enter and exit
- delete mode (any mode the terminal needs to be placed in
+ Finally, you can specify <STRONG>dch1</STRONG> to delete a single charac-
+ ter, <STRONG>dch</STRONG> with one parameter, <EM>n</EM>, to delete <EM>n</EM> <EM>characters,</EM>
+ and delete mode by giving <STRONG>smdc</STRONG> and <STRONG>rmdc</STRONG> to enter and exit
+ delete mode (any mode the terminal needs to be placed in
for <STRONG>dch1</STRONG> to work).
- A command to erase <EM>n</EM> characters (equivalent to outputting
- <EM>n</EM> blanks without moving the cursor) can be given as <STRONG>ech</STRONG>
+ A command to erase <EM>n</EM> characters (equivalent to outputting
+ <EM>n</EM> blanks without moving the cursor) can be given as <STRONG>ech</STRONG>
with one parameter.
</PRE><H3><a name="h3-Highlighting_-Underlining_-and-Visible-Bells">Highlighting, Underlining, and Visible Bells</a></H3><PRE>
If your terminal has one or more kinds of display
- attributes, these can be represented in a number of dif-
+ attributes, these can be represented in a number of dif-
ferent ways. You should choose one display form as <EM>stand-</EM>
<EM>out</EM> <EM>mode</EM>, representing a good, high contrast, easy-on-the-
- eyes, format for highlighting error messages and other
- attention getters. (If you have a choice, reverse video
- plus half-bright is good, or reverse video alone.) The
- sequences to enter and exit standout mode are given as
- <STRONG>smso</STRONG> and <STRONG>rmso</STRONG>, respectively. If the code to change into
- or out of standout mode leaves one or even two blank spa-
- ces on the screen, as the TVI 912 and Teleray 1061 do,
+ eyes, format for highlighting error messages and other
+ attention getters. (If you have a choice, reverse video
+ plus half-bright is good, or reverse video alone.) The
+ sequences to enter and exit standout mode are given as
+ <STRONG>smso</STRONG> and <STRONG>rmso</STRONG>, respectively. If the code to change into
+ or out of standout mode leaves one or even two blank spa-
+ ces on the screen, as the TVI 912 and Teleray 1061 do,
then <STRONG>xmc</STRONG> should be given to tell how many spaces are left.
- Codes to begin underlining and end underlining can be
- given as <STRONG>smul</STRONG> and <STRONG>rmul</STRONG> respectively. If the terminal has
- a code to underline the current character and move the
+ Codes to begin underlining and end underlining can be
+ given as <STRONG>smul</STRONG> and <STRONG>rmul</STRONG> respectively. If the terminal has
+ a code to underline the current character and move the
cursor one space to the right, such as the Microterm Mime,
this can be given as <STRONG>uc</STRONG>.
- Other capabilities to enter various highlighting modes
- include <STRONG>blink</STRONG> (blinking) <STRONG>bold</STRONG> (bold or extra bright) <STRONG>dim</STRONG>
- (dim or half-bright) <STRONG>invis</STRONG> (blanking or invisible text)
- <STRONG>prot</STRONG> (protected) <STRONG>rev</STRONG> (reverse video) <STRONG>sgr0</STRONG> (turn off <EM>all</EM>
- attribute modes) <STRONG>smacs</STRONG> (enter alternate character set
- mode) and <STRONG>rmacs</STRONG> (exit alternate character set mode).
- Turning on any of these modes singly may or may not turn
+ Other capabilities to enter various highlighting modes
+ include <STRONG>blink</STRONG> (blinking) <STRONG>bold</STRONG> (bold or extra bright) <STRONG>dim</STRONG>
+ (dim or half-bright) <STRONG>invis</STRONG> (blanking or invisible text)
+ <STRONG>prot</STRONG> (protected) <STRONG>rev</STRONG> (reverse video) <STRONG>sgr0</STRONG> (turn off <EM>all</EM>
+ attribute modes) <STRONG>smacs</STRONG> (enter alternate character set
+ mode) and <STRONG>rmacs</STRONG> (exit alternate character set mode).
+ Turning on any of these modes singly may or may not turn
off other modes.
- If there is a sequence to set arbitrary combinations of
- modes, this should be given as <STRONG>sgr</STRONG> (set attributes), tak-
- ing 9 parameters. Each parameter is either 0 or nonzero,
+ If there is a sequence to set arbitrary combinations of
+ modes, this should be given as <STRONG>sgr</STRONG> (set attributes), tak-
+ ing 9 parameters. Each parameter is either 0 or nonzero,
as the corresponding attribute is on or off. The 9 param-
- eters are, in order: standout, underline, reverse, blink,
- dim, bold, blank, protect, alternate character set. Not
- all modes need be supported by <STRONG>sgr</STRONG>, only those for which
+ eters are, in order: standout, underline, reverse, blink,
+ dim, bold, blank, protect, alternate character set. Not
+ all modes need be supported by <STRONG>sgr</STRONG>, only those for which
corresponding separate attribute commands exist.
For example, the DEC vt220 supports most of the modes:
p8 protect not used
p9 altcharset ^O (off) ^N (on)
- We begin each escape sequence by turning off any existing
- modes, since there is no quick way to determine whether
+ We begin each escape sequence by turning off any existing
+ modes, since there is no quick way to determine whether
they are active. Standout is set up to be the combination
- of reverse and bold. The vt220 terminal has a protect
- mode, though it is not commonly used in sgr because it
- protects characters on the screen from the host's era-
- sures. The altcharset mode also is different in that it
- is either ^O or ^N, depending on whether it is off or on.
- If all modes are turned on, the resulting sequence is
+ of reverse and bold. The vt220 terminal has a protect
+ mode, though it is not commonly used in sgr because it
+ protects characters on the screen from the host's era-
+ sures. The altcharset mode also is different in that it
+ is either ^O or ^N, depending on whether it is off or on.
+ If all modes are turned on, the resulting sequence is
\E[0;1;4;5;7;8m^N.
- Some sequences are common to different modes. For exam-
- ple, ;7 is output when either p1 or p3 is true, that is,
+ Some sequences are common to different modes. For exam-
+ ple, ;7 is output when either p1 or p3 is true, that is,
if either standout or reverse modes are turned on.
- Writing out the above sequences, along with their depen-
+ Writing out the above sequences, along with their depen-
dencies yields
<STRONG>sequence</STRONG> <STRONG>when</STRONG> <STRONG>to</STRONG> <STRONG>output</STRONG> <STRONG>terminfo</STRONG> <STRONG>translation</STRONG>
sgr=\E[0%?%p1%p6%|%t;1%;%?%p2%t;4%;%?%p4%t;5%;
%?%p1%p3%|%t;7%;%?%p7%t;8%;m%?%p9%t\016%e\017%;,
- Remember that if you specify sgr, you must also specify
- sgr0. Also, some implementations rely on sgr being given
- if sgr0 is, Not all terminfo entries necessarily have an
- sgr string, however. Many terminfo entries are derived
- from termcap entries which have no sgr string. The only
- drawback to adding an sgr string is that termcap also
- assumes that sgr0 does not exit alternate character set
+ Remember that if you specify sgr, you must also specify
+ sgr0. Also, some implementations rely on sgr being given
+ if sgr0 is, Not all terminfo entries necessarily have an
+ sgr string, however. Many terminfo entries are derived
+ from termcap entries which have no sgr string. The only
+ drawback to adding an sgr string is that termcap also
+ assumes that sgr0 does not exit alternate character set
mode.
- Terminals with the "magic cookie" glitch (<STRONG>xmc</STRONG>) deposit
+ Terminals with the "magic cookie" glitch (<STRONG>xmc</STRONG>) deposit
special "cookies" when they receive mode-setting
- sequences, which affect the display algorithm rather than
- having extra bits for each character. Some terminals,
- such as the HP 2621, automatically leave standout mode
- when they move to a new line or the cursor is addressed.
- Programs using standout mode should exit standout mode
- before moving the cursor or sending a newline, unless the
- <STRONG>msgr</STRONG> capability, asserting that it is safe to move in
+ sequences, which affect the display algorithm rather than
+ having extra bits for each character. Some terminals,
+ such as the HP 2621, automatically leave standout mode
+ when they move to a new line or the cursor is addressed.
+ Programs using standout mode should exit standout mode
+ before moving the cursor or sending a newline, unless the
+ <STRONG>msgr</STRONG> capability, asserting that it is safe to move in
standout mode, is present.
- If the terminal has a way of flashing the screen to indi-
- cate an error quietly (a bell replacement) then this can
+ If the terminal has a way of flashing the screen to indi-
+ cate an error quietly (a bell replacement) then this can
be given as <STRONG>flash</STRONG>; it must not move the cursor.
- If the cursor needs to be made more visible than normal
+ If the cursor needs to be made more visible than normal
when it is not on the bottom line (to make, for example, a
- non-blinking underline into an easier to find block or
+ non-blinking underline into an easier to find block or
blinking underline) give this sequence as <STRONG>cvvis</STRONG>. If there
- is a way to make the cursor completely invisible, give
+ is a way to make the cursor completely invisible, give
that as <STRONG>civis</STRONG>. The capability <STRONG>cnorm</STRONG> should be given which
undoes the effects of both of these modes.
If your terminal correctly generates underlined characters
- (with no special codes needed) even though it does not
- overstrike, then you should give the capability <STRONG>ul</STRONG>. If a
- character overstriking another leaves both characters on
+ (with no special codes needed) even though it does not
+ overstrike, then you should give the capability <STRONG>ul</STRONG>. If a
+ character overstriking another leaves both characters on
the screen, specify the capability <STRONG>os</STRONG>. If overstrikes are
- erasable with a blank, then this should be indicated by
+ erasable with a blank, then this should be indicated by
giving <STRONG>eo</STRONG>.
</PRE><H3><a name="h3-Keypad-and-Function-Keys">Keypad and Function Keys</a></H3><PRE>
If the terminal has a keypad that transmits codes when the
- keys are pressed, this information can be given. Note
+ keys are pressed, this information can be given. Note
that it is not possible to handle terminals where the key-
pad only works in local (this applies, for example, to the
- unshifted HP 2621 keys). If the keypad can be set to
- transmit or not transmit, give these codes as <STRONG>smkx</STRONG> and
+ unshifted HP 2621 keys). If the keypad can be set to
+ transmit or not transmit, give these codes as <STRONG>smkx</STRONG> and
<STRONG>rmkx</STRONG>. Otherwise the keypad is assumed to always transmit.
- The codes sent by the left arrow, right arrow, up arrow,
- down arrow, and home keys can be given as <STRONG>kcub1,</STRONG> <STRONG>kcuf1,</STRONG>
- <STRONG>kcuu1,</STRONG> <STRONG>kcud1,</STRONG> and <STRONG>khome</STRONG> respectively. If there are func-
- tion keys such as f0, f1, ..., f10, the codes they send
- can be given as <STRONG>kf0,</STRONG> <STRONG>kf1,</STRONG> <STRONG>...,</STRONG> <STRONG>kf10</STRONG>. If these keys have
- labels other than the default f0 through f10, the labels
+ The codes sent by the left arrow, right arrow, up arrow,
+ down arrow, and home keys can be given as <STRONG>kcub1,</STRONG> <STRONG>kcuf1,</STRONG>
+ <STRONG>kcuu1,</STRONG> <STRONG>kcud1,</STRONG> and <STRONG>khome</STRONG> respectively. If there are func-
+ tion keys such as f0, f1, ..., f10, the codes they send
+ can be given as <STRONG>kf0,</STRONG> <STRONG>kf1,</STRONG> <STRONG>...,</STRONG> <STRONG>kf10</STRONG>. If these keys have
+ labels other than the default f0 through f10, the labels
can be given as <STRONG>lf0,</STRONG> <STRONG>lf1,</STRONG> <STRONG>...,</STRONG> <STRONG>lf10</STRONG>.
The codes transmitted by certain other special keys can be
<STRONG>o</STRONG> <STRONG>khts</STRONG> (set a tab stop in this column).
- In addition, if the keypad has a 3 by 3 array of keys
- including the four arrow keys, the other five keys can be
+ In addition, if the keypad has a 3 by 3 array of keys
+ including the four arrow keys, the other five keys can be
given as <STRONG>ka1</STRONG>, <STRONG>ka3</STRONG>, <STRONG>kb2</STRONG>, <STRONG>kc1</STRONG>, and <STRONG>kc3</STRONG>. These keys are use-
- ful when the effects of a 3 by 3 directional pad are
+ ful when the effects of a 3 by 3 directional pad are
needed.
- Strings to program function keys can be given as <STRONG>pfkey</STRONG>,
- <STRONG>pfloc</STRONG>, and <STRONG>pfx</STRONG>. A string to program screen labels should
- be specified as <STRONG>pln</STRONG>. Each of these strings takes two
- parameters: the function key number to program (from 0 to
- 10) and the string to program it with. Function key num-
- bers out of this range may program undefined keys in a
- terminal dependent manner. The difference between the
- capabilities is that <STRONG>pfkey</STRONG> causes pressing the given key
- to be the same as the user typing the given string; <STRONG>pfloc</STRONG>
+ Strings to program function keys can be given as <STRONG>pfkey</STRONG>,
+ <STRONG>pfloc</STRONG>, and <STRONG>pfx</STRONG>. A string to program screen labels should
+ be specified as <STRONG>pln</STRONG>. Each of these strings takes two
+ parameters: the function key number to program (from 0 to
+ 10) and the string to program it with. Function key num-
+ bers out of this range may program undefined keys in a
+ terminal dependent manner. The difference between the
+ capabilities is that <STRONG>pfkey</STRONG> causes pressing the given key
+ to be the same as the user typing the given string; <STRONG>pfloc</STRONG>
causes the string to be executed by the terminal in local;
- and <STRONG>pfx</STRONG> causes the string to be transmitted to the com-
+ and <STRONG>pfx</STRONG> causes the string to be transmitted to the com-
puter.
The capabilities <STRONG>nlab</STRONG>, <STRONG>lw</STRONG> and <STRONG>lh</STRONG> define the number of pro-
- grammable screen labels and their width and height. If
- there are commands to turn the labels on and off, give
- them in <STRONG>smln</STRONG> and <STRONG>rmln</STRONG>. <STRONG>smln</STRONG> is normally output after one
+ grammable screen labels and their width and height. If
+ there are commands to turn the labels on and off, give
+ them in <STRONG>smln</STRONG> and <STRONG>rmln</STRONG>. <STRONG>smln</STRONG> is normally output after one
or more pln sequences to make sure that the change becomes
visible.
</PRE><H3><a name="h3-Tabs-and-Initialization">Tabs and Initialization</a></H3><PRE>
- If the terminal has hardware tabs, the command to advance
- to the next tab stop can be given as <STRONG>ht</STRONG> (usually control
+ If the terminal has hardware tabs, the command to advance
+ to the next tab stop can be given as <STRONG>ht</STRONG> (usually control
I). A "back-tab" command which moves leftward to the pre-
- ceding tab stop can be given as <STRONG>cbt</STRONG>. By convention, if
- the teletype modes indicate that tabs are being expanded
- by the computer rather than being sent to the terminal,
- programs should not use <STRONG>ht</STRONG> or <STRONG>cbt</STRONG> even if they are
- present, since the user may not have the tab stops prop-
- erly set. If the terminal has hardware tabs which are
- initially set every <EM>n</EM> spaces when the terminal is powered
- up, the numeric parameter <STRONG>it</STRONG> is given, showing the number
- of spaces the tabs are set to. This is normally used by
- the <STRONG>tset</STRONG> command to determine whether to set the mode for
- hardware tab expansion, and whether to set the tab stops.
- If the terminal has tab stops that can be saved in non-
- volatile memory, the terminfo description can assume that
+ ceding tab stop can be given as <STRONG>cbt</STRONG>. By convention, if
+ the teletype modes indicate that tabs are being expanded
+ by the computer rather than being sent to the terminal,
+ programs should not use <STRONG>ht</STRONG> or <STRONG>cbt</STRONG> even if they are
+ present, since the user may not have the tab stops prop-
+ erly set. If the terminal has hardware tabs which are
+ initially set every <EM>n</EM> spaces when the terminal is powered
+ up, the numeric parameter <STRONG>it</STRONG> is given, showing the number
+ of spaces the tabs are set to. This is normally used by
+ the <STRONG>tset</STRONG> command to determine whether to set the mode for
+ hardware tab expansion, and whether to set the tab stops.
+ If the terminal has tab stops that can be saved in non-
+ volatile memory, the terminfo description can assume that
they are properly set.
- Other capabilities include <STRONG>is1</STRONG>, <STRONG>is2</STRONG>, and <STRONG>is3</STRONG>, initializa-
- tion strings for the terminal, <STRONG>iprog</STRONG>, the path name of a
- program to be run to initialize the terminal, and <STRONG>if</STRONG>, the
- name of a file containing long initialization strings.
- These strings are expected to set the terminal into modes
- consistent with the rest of the terminfo description.
+ Other capabilities include <STRONG>is1</STRONG>, <STRONG>is2</STRONG>, and <STRONG>is3</STRONG>, initializa-
+ tion strings for the terminal, <STRONG>iprog</STRONG>, the path name of a
+ program to be run to initialize the terminal, and <STRONG>if</STRONG>, the
+ name of a file containing long initialization strings.
+ These strings are expected to set the terminal into modes
+ consistent with the rest of the terminfo description.
They are normally sent to the terminal, by the <EM>init</EM> option
- of the <STRONG>tput</STRONG> program, each time the user logs in. They
+ of the <STRONG>tput</STRONG> program, each time the user logs in. They
will be printed in the following order:
run the program
and finally
output <STRONG>is3</STRONG>.
- Most initialization is done with <STRONG>is2</STRONG>. Special terminal
+ Most initialization is done with <STRONG>is2</STRONG>. Special terminal
modes can be set up without duplicating strings by putting
- the common sequences in <STRONG>is2</STRONG> and special cases in <STRONG>is1</STRONG> and
+ the common sequences in <STRONG>is2</STRONG> and special cases in <STRONG>is1</STRONG> and
<STRONG>is3</STRONG>.
A set of sequences that does a harder reset from a totally
unknown state can be given as <STRONG>rs1</STRONG>, <STRONG>rs2</STRONG>, <STRONG>rf</STRONG> and <STRONG>rs3</STRONG>, analo-
- gous to <STRONG>is1</STRONG> <STRONG>,</STRONG> <STRONG>is2</STRONG> <STRONG>,</STRONG> <STRONG>if</STRONG> and <STRONG>is3</STRONG> respectively. These
- strings are output by the <STRONG>reset</STRONG> program, which is used
- when the terminal gets into a wedged state. Commands are
- normally placed in <STRONG>rs1</STRONG>, <STRONG>rs2</STRONG> <STRONG>rs3</STRONG> and <STRONG>rf</STRONG> only if they pro-
- duce annoying effects on the screen and are not necessary
- when logging in. For example, the command to set the
- vt100 into 80-column mode would normally be part of <STRONG>is2</STRONG>,
- but it causes an annoying glitch of the screen and is not
- normally needed since the terminal is usually already in
+ gous to <STRONG>is1</STRONG> <STRONG>,</STRONG> <STRONG>is2</STRONG> <STRONG>,</STRONG> <STRONG>if</STRONG> and <STRONG>is3</STRONG> respectively. These
+ strings are output by the <STRONG>reset</STRONG> program, which is used
+ when the terminal gets into a wedged state. Commands are
+ normally placed in <STRONG>rs1</STRONG>, <STRONG>rs2</STRONG> <STRONG>rs3</STRONG> and <STRONG>rf</STRONG> only if they pro-
+ duce annoying effects on the screen and are not necessary
+ when logging in. For example, the command to set the
+ vt100 into 80-column mode would normally be part of <STRONG>is2</STRONG>,
+ but it causes an annoying glitch of the screen and is not
+ normally needed since the terminal is usually already in
80 column mode.
The <STRONG>reset</STRONG> program writes strings including <STRONG>iprog</STRONG>, etc., in
- the same order as the <EM>init</EM> program, using <STRONG>rs1</STRONG>, etc.,
+ the same order as the <EM>init</EM> program, using <STRONG>rs1</STRONG>, etc.,
instead of <STRONG>is1</STRONG>, etc. If any of <STRONG>rs1</STRONG>, <STRONG>rs2</STRONG>, <STRONG>rs3</STRONG>, or <STRONG>rf</STRONG> reset
- capability strings are missing, the <STRONG>reset</STRONG> program falls
+ capability strings are missing, the <STRONG>reset</STRONG> program falls
back upon the corresponding initialization capability
string.
If there are commands to set and clear tab stops, they can
- be given as <STRONG>tbc</STRONG> (clear all tab stops) and <STRONG>hts</STRONG> (set a tab
- stop in the current column of every row). If a more com-
- plex sequence is needed to set the tabs than can be
- described by this, the sequence can be placed in <STRONG>is2</STRONG> or
+ be given as <STRONG>tbc</STRONG> (clear all tab stops) and <STRONG>hts</STRONG> (set a tab
+ stop in the current column of every row). If a more com-
+ plex sequence is needed to set the tabs than can be
+ described by this, the sequence can be placed in <STRONG>is2</STRONG> or
<STRONG>if</STRONG>.
</PRE><H3><a name="h3-Delays-and-Padding">Delays and Padding</a></H3><PRE>
- Many older and slower terminals do not support either
+ Many older and slower terminals do not support either
XON/XOFF or DTR handshaking, including hard copy terminals
- and some very archaic CRTs (including, for example, DEC
- VT100s). These may require padding characters after cer-
+ and some very archaic CRTs (including, for example, DEC
+ VT100s). These may require padding characters after cer-
tain cursor motions and screen changes.
If the terminal uses xon/xoff handshaking for flow control
- (that is, it automatically emits ^S back to the host when
+ (that is, it automatically emits ^S back to the host when
its input buffers are close to full), set <STRONG>xon</STRONG>. This capa-
- bility suppresses the emission of padding. You can also
- set it for memory-mapped console devices effectively that
- do not have a speed limit. Padding information should
- still be included so that routines can make better deci-
+ bility suppresses the emission of padding. You can also
+ set it for memory-mapped console devices effectively that
+ do not have a speed limit. Padding information should
+ still be included so that routines can make better deci-
sions about relative costs, but actual pad characters will
not be transmitted.
- If <STRONG>pb</STRONG> (padding baud rate) is given, padding is suppressed
- at baud rates below the value of <STRONG>pb</STRONG>. If the entry has no
- padding baud rate, then whether padding is emitted or not
+ If <STRONG>pb</STRONG> (padding baud rate) is given, padding is suppressed
+ at baud rates below the value of <STRONG>pb</STRONG>. If the entry has no
+ padding baud rate, then whether padding is emitted or not
is completely controlled by <STRONG>xon</STRONG>.
- If the terminal requires other than a null (zero) charac-
- ter as a pad, then this can be given as <STRONG>pad</STRONG>. Only the
+ If the terminal requires other than a null (zero) charac-
+ ter as a pad, then this can be given as <STRONG>pad</STRONG>. Only the
first character of the <STRONG>pad</STRONG> string is used.
</PRE><H3><a name="h3-Status-Lines">Status Lines</a></H3><PRE>
- Some terminals have an extra "status line" which is not
- normally used by software (and thus not counted in the
+ Some terminals have an extra "status line" which is not
+ normally used by software (and thus not counted in the
terminal's <STRONG>lines</STRONG> capability).
- The simplest case is a status line which is cursor-
- addressable but not part of the main scrolling region on
- the screen; the Heathkit H19 has a status line of this
- kind, as would a 24-line VT100 with a 23-line scrolling
- region set up on initialization. This situation is indi-
+ The simplest case is a status line which is cursor-
+ addressable but not part of the main scrolling region on
+ the screen; the Heathkit H19 has a status line of this
+ kind, as would a 24-line VT100 with a 23-line scrolling
+ region set up on initialization. This situation is indi-
cated by the <STRONG>hs</STRONG> capability.
Some terminals with status lines need special sequences to
- access the status line. These may be expressed as a
+ access the status line. These may be expressed as a
string with single parameter <STRONG>tsl</STRONG> which takes the cursor to
- a given zero-origin column on the status line. The capa-
+ a given zero-origin column on the status line. The capa-
bility <STRONG>fsl</STRONG> must return to the main-screen cursor positions
- before the last <STRONG>tsl</STRONG>. You may need to embed the string
- values of <STRONG>sc</STRONG> (save cursor) and <STRONG>rc</STRONG> (restore cursor) in <STRONG>tsl</STRONG>
+ before the last <STRONG>tsl</STRONG>. You may need to embed the string
+ values of <STRONG>sc</STRONG> (save cursor) and <STRONG>rc</STRONG> (restore cursor) in <STRONG>tsl</STRONG>
and <STRONG>fsl</STRONG> to accomplish this.
- The status line is normally assumed to be the same width
- as the width of the terminal. If this is untrue, you can
+ The status line is normally assumed to be the same width
+ as the width of the terminal. If this is untrue, you can
specify it with the numeric capability <STRONG>wsl</STRONG>.
- A command to erase or blank the status line may be speci-
+ A command to erase or blank the status line may be speci-
fied as <STRONG>dsl</STRONG>.
- The boolean capability <STRONG>eslok</STRONG> specifies that escape
+ The boolean capability <STRONG>eslok</STRONG> specifies that escape
sequences, tabs, etc., work ordinarily in the status line.
- The <STRONG>ncurses</STRONG> implementation does not yet use any of these
- capabilities. They are documented here in case they ever
+ The <STRONG>ncurses</STRONG> implementation does not yet use any of these
+ capabilities. They are documented here in case they ever
become important.
</PRE><H3><a name="h3-Line-Graphics">Line Graphics</a></H3><PRE>
- Many terminals have alternate character sets useful for
- forms-drawing. Terminfo and <STRONG>curses</STRONG> build in support for
- the drawing characters supported by the VT100, with some
- characters from the AT&T 4410v1 added. This alternate
+ Many terminals have alternate character sets useful for
+ forms-drawing. Terminfo and <STRONG>curses</STRONG> built-in support for
+ the drawing characters supported by the VT100, with some
+ characters from the AT&T 4410v1 added. This alternate
character set may be specified by the <STRONG>acsc</STRONG> capability.
- <STRONG>Glyph</STRONG> <STRONG>ACS</STRONG> <STRONG>Ascii</STRONG> <STRONG>VT100</STRONG>
- <STRONG>Name</STRONG> <STRONG>Name</STRONG> <STRONG>Default</STRONG> <STRONG>Name</STRONG>
- UK pound sign ACS_STERLING f }
- arrow pointing down ACS_DARROW v .
- arrow pointing left ACS_LARROW < ,
- arrow pointing right ACS_RARROW > +
- arrow pointing up ACS_UARROW ^ -
- board of squares ACS_BOARD # h
- bullet ACS_BULLET o ~
- checker board (stipple) ACS_CKBOARD : a
- degree symbol ACS_DEGREE \ f
- diamond ACS_DIAMOND + `
- greater-than-or-equal-to ACS_GEQUAL > z
- greek pi ACS_PI * {
-
- horizontal line ACS_HLINE - q
- lantern symbol ACS_LANTERN # i
- large plus or crossover ACS_PLUS + n
- less-than-or-equal-to ACS_LEQUAL < y
- lower left corner ACS_LLCORNER + m
- lower right corner ACS_LRCORNER + j
- not-equal ACS_NEQUAL ! |
- plus/minus ACS_PLMINUS # g
- scan line 1 ACS_S1 ~ o
- scan line 3 ACS_S3 - p
- scan line 7 ACS_S7 - r
- scan line 9 ACS_S9 _ s
- solid square block ACS_BLOCK # 0
- tee pointing down ACS_TTEE + w
- tee pointing left ACS_RTEE + u
- tee pointing right ACS_LTEE + t
- tee pointing up ACS_BTEE + v
- upper left corner ACS_ULCORNER + l
- upper right corner ACS_URCORNER + k
- vertical line ACS_VLINE | x
-
- The best way to define a new device's graphics set is to
- add a column to a copy of this table for your terminal,
- giving the character which (when emitted between
- <STRONG>smacs</STRONG>/<STRONG>rmacs</STRONG> switches) will be rendered as the correspond-
- ing graphic. Then read off the VT100/your terminal char-
- acter pairs right to left in sequence; these become the
+ <STRONG>Glyph</STRONG> <STRONG>ACS</STRONG> <STRONG>Ascii</STRONG> <STRONG>VT100</STRONG> <STRONG>VT100</STRONG>
+
+ <STRONG>Name</STRONG> <STRONG>Name</STRONG> <STRONG>DefaultChar</STRONG> <STRONG>Code</STRONG>
+ -----------------------------------------------------------
+ arrow pointing right ACS_RARROW > + 0x2b
+ arrow pointing left ACS_LARROW < , 0x2c
+ arrow pointing up ACS_UARROW ^ - 0x2d
+ arrow pointing down ACS_DARROW v . 0x2e
+ solid square block ACS_BLOCK # 0 0x30
+ diamond ACS_DIAMOND + ` 0x60
+ checker board (stipple) ACS_CKBOARD : a 0x61
+ degree symbol ACS_DEGREE \ f 0x66
+ plus/minus ACS_PLMINUS # g 0x67
+ board of squares ACS_BOARD # h 0x68
+ lantern symbol ACS_LANTERN # i 0x69
+ lower right corner ACS_LRCORNER + j 0x6a
+ upper right corner ACS_URCORNER + k 0x6b
+ upper left corner ACS_ULCORNER + l 0x6c
+ lower left corner ACS_LLCORNER + m 0x6d
+ large plus or crossover ACS_PLUS + n 0x6e
+ scan line 1 ACS_S1 ~ o 0x6f
+ scan line 3 ACS_S3 - p 0x70
+ horizontal line ACS_HLINE - q 0x71
+ scan line 7 ACS_S7 - r 0x72
+ scan line 9 ACS_S9 _ s 0x73
+ tee pointing right ACS_LTEE + t 0x74
+ tee pointing left ACS_RTEE + u 0x75
+ tee pointing up ACS_BTEE + v 0x76
+ tee pointing down ACS_TTEE + w 0x77
+ vertical line ACS_VLINE | x 0x78
+ less-than-or-equal-to ACS_LEQUAL < y 0x79
+ greater-than-or-equal-to ACS_GEQUAL > z 0x7a
+ greek pi ACS_PI * { 0x7b
+ not-equal ACS_NEQUAL ! | 0x7c
+ UK pound sign ACS_STERLING f } 0x7d
+ bullet ACS_BULLET o ~ 0x7e
+
+ A few notes apply to the table itself:
+
+ <STRONG>o</STRONG> X/Open Curses incorrectly states that the mapping for
+ <EM>lantern</EM> is uppercase "I" although Unix implementations
+ use the lowercase "i" mapping.
+
+ <STRONG>o</STRONG> The DEC VT100 implemented graphics using the alternate
+ character set feature, temporarily switching <EM>modes</EM> and
+ sending characters in the range 0x60 (96) to 0x7e
+ (126).
+
+ <STRONG>o</STRONG> The AT&T terminal added graphics characters outside
+ that range.
+
+ The best way to define a new device's graphics set is to
+ add a column to a copy of this table for your terminal,
+ giving the character which (when emitted between
+ <STRONG>smacs</STRONG>/<STRONG>rmacs</STRONG> switches) will be rendered as the correspond-
+ ing graphic. Then read off the VT100/your terminal char-
+ acter pairs right to left in sequence; these become the
ACSC string.
</PRE><H3><a name="h3-Color-Handling">Color Handling</a></H3><PRE>
- The curses library functions <STRONG>init_pair</STRONG> and <STRONG>init_color</STRONG>
- manipulate the <EM>color</EM> <EM>pairs</EM> and <EM>color</EM> <EM>values</EM> discussed in
- this section (see <STRONG><A HREF="curs_color.3x.html">curs_color(3x)</A></STRONG> for details on these and
+ The curses library functions <STRONG>init_pair</STRONG> and <STRONG>init_color</STRONG>
+ manipulate the <EM>color</EM> <EM>pairs</EM> and <EM>color</EM> <EM>values</EM> discussed in
+ this section (see <STRONG><A HREF="curs_color.3x.html">curs_color(3x)</A></STRONG> for details on these and
related functions).
- Most color terminals are either "Tektronix-like" or "HP-
+ Most color terminals are either "Tektronix-like" or "HP-
like":
- <STRONG>o</STRONG> Tektronix-like terminals have a predefined set of <EM>N</EM>
- colors (where <EM>N</EM> is usually 8), and can set character-
- cell foreground and background characters indepen-
+ <STRONG>o</STRONG> Tektronix-like terminals have a predefined set of <EM>N</EM>
+ colors (where <EM>N</EM> is usually 8), and can set character-
+ cell foreground and background characters indepen-
dently, mixing them into <EM>N</EM> * <EM>N</EM> color-pairs.
- <STRONG>o</STRONG> On HP-like terminals, the user must set each color
- pair up separately (foreground and background are not
- independently settable). Up to <EM>M</EM> color-pairs may be
- set up from 2*<EM>M</EM> different colors. ANSI-compatible
+ <STRONG>o</STRONG> On HP-like terminals, the user must set each color
+ pair up separately (foreground and background are not
+ independently settable). Up to <EM>M</EM> color-pairs may be
+ set up from 2*<EM>M</EM> different colors. ANSI-compatible
terminals are Tektronix-like.
Some basic color capabilities are independent of the color
method. The numeric capabilities <STRONG>colors</STRONG> and <STRONG>pairs</STRONG> specify
- the maximum numbers of colors and color-pairs that can be
- displayed simultaneously. The <STRONG>op</STRONG> (original pair) string
- resets foreground and background colors to their default
- values for the terminal. The <STRONG>oc</STRONG> string resets all colors
- or color-pairs to their default values for the terminal.
- Some terminals (including many PC terminal emulators)
- erase screen areas with the current background color
- rather than the power-up default background; these should
+ the maximum numbers of colors and color-pairs that can be
+ displayed simultaneously. The <STRONG>op</STRONG> (original pair) string
+ resets foreground and background colors to their default
+ values for the terminal. The <STRONG>oc</STRONG> string resets all colors
+ or color-pairs to their default values for the terminal.
+ Some terminals (including many PC terminal emulators)
+ erase screen areas with the current background color
+ rather than the power-up default background; these should
have the boolean capability <STRONG>bce</STRONG>.
- While the curses library works with <EM>color</EM> <EM>pairs</EM> (reflect-
- ing the inability of some devices to set foreground and
+ While the curses library works with <EM>color</EM> <EM>pairs</EM> (reflect-
+ ing the inability of some devices to set foreground and
background colors independently), there are separate capa-
bilities for setting these features:
- <STRONG>o</STRONG> To change the current foreground or background color
- on a Tektronix-type terminal, use <STRONG>setaf</STRONG> (set ANSI
- foreground) and <STRONG>setab</STRONG> (set ANSI background) or <STRONG>setf</STRONG>
- (set foreground) and <STRONG>setb</STRONG> (set background). These
- take one parameter, the color number. The SVr4 docu-
- mentation describes only <STRONG>setaf</STRONG>/<STRONG>setab</STRONG>; the XPG4 draft
+ <STRONG>o</STRONG> To change the current foreground or background color
+ on a Tektronix-type terminal, use <STRONG>setaf</STRONG> (set ANSI
+ foreground) and <STRONG>setab</STRONG> (set ANSI background) or <STRONG>setf</STRONG>
+ (set foreground) and <STRONG>setb</STRONG> (set background). These
+ take one parameter, the color number. The SVr4 docu-
+ mentation describes only <STRONG>setaf</STRONG>/<STRONG>setab</STRONG>; the XPG4 draft
says that "If the terminal supports ANSI escape
sequences to set background and foreground, they
should be coded as <STRONG>setaf</STRONG> and <STRONG>setab</STRONG>, respectively.
<STRONG>o</STRONG> If the terminal supports other escape sequences to set
- background and foreground, they should be coded as
- <STRONG>setf</STRONG> and <STRONG>setb</STRONG>, respectively. The <STRONG>vidputs</STRONG> and the
+ background and foreground, they should be coded as
+ <STRONG>setf</STRONG> and <STRONG>setb</STRONG>, respectively. The <STRONG>vidputs</STRONG> and the
<STRONG><A HREF="curs_refresh.3x.html">refresh(3x)</A></STRONG> functions use the <STRONG>setaf</STRONG> and <STRONG>setab</STRONG> capabil-
ities if they are defined.
- The <STRONG>setaf</STRONG>/<STRONG>setab</STRONG> and <STRONG>setf</STRONG>/<STRONG>setb</STRONG> capabilities take a single
+ The <STRONG>setaf</STRONG>/<STRONG>setab</STRONG> and <STRONG>setf</STRONG>/<STRONG>setb</STRONG> capabilities take a single
numeric argument each. Argument values 0-7 of <STRONG>setaf</STRONG>/<STRONG>setab</STRONG>
- are portably defined as follows (the middle column is the
+ are portably defined as follows (the middle column is the
symbolic #define available in the header for the <STRONG>curses</STRONG> or
- <STRONG>ncurses</STRONG> libraries). The terminal hardware is free to map
- these as it likes, but the RGB values indicate normal
+ <STRONG>ncurses</STRONG> libraries). The terminal hardware is free to map
+ these as it likes, but the RGB values indicate normal
locations in color space.
<STRONG>Color</STRONG> <STRONG>#define</STRONG> <STRONG>Value</STRONG> <STRONG>RGB</STRONG>
cyan <STRONG>COLOR_CYAN</STRONG> 6 0,max,max
white <STRONG>COLOR_WHITE</STRONG> 7 max,max,max
- The argument values of <STRONG>setf</STRONG>/<STRONG>setb</STRONG> historically correspond
+ The argument values of <STRONG>setf</STRONG>/<STRONG>setb</STRONG> historically correspond
to a different mapping, i.e.,
<STRONG>Color</STRONG> <STRONG>#define</STRONG> <STRONG>Value</STRONG> <STRONG>RGB</STRONG>
white <STRONG>COLOR_WHITE</STRONG> 7 max,max,max
It is important to not confuse the two sets of color capa-
- bilities; otherwise red/blue will be interchanged on the
+ bilities; otherwise red/blue will be interchanged on the
display.
- On an HP-like terminal, use <STRONG>scp</STRONG> with a color-pair number
+ On an HP-like terminal, use <STRONG>scp</STRONG> with a color-pair number
parameter to set which color pair is current.
Some terminals allow the <EM>color</EM> <EM>values</EM> to be modified:
- <STRONG>o</STRONG> On a Tektronix-like terminal, the capability <STRONG>ccc</STRONG> may
- be present to indicate that colors can be modified.
- If so, the <STRONG>initc</STRONG> capability will take a color number
- (0 to <STRONG>colors</STRONG> - 1)and three more parameters which
+ <STRONG>o</STRONG> On a Tektronix-like terminal, the capability <STRONG>ccc</STRONG> may
+ be present to indicate that colors can be modified.
+ If so, the <STRONG>initc</STRONG> capability will take a color number
+ (0 to <STRONG>colors</STRONG> - 1)and three more parameters which
describe the color. These three parameters default to
- being interpreted as RGB (Red, Green, Blue) values.
- If the boolean capability <STRONG>hls</STRONG> is present, they are
- instead as HLS (Hue, Lightness, Saturation) indices.
+ being interpreted as RGB (Red, Green, Blue) values.
+ If the boolean capability <STRONG>hls</STRONG> is present, they are
+ instead as HLS (Hue, Lightness, Saturation) indices.
The ranges are terminal-dependent.
- <STRONG>o</STRONG> On an HP-like terminal, <STRONG>initp</STRONG> may give a capability
- for changing a color-pair value. It will take seven
- parameters; a color-pair number (0 to <STRONG>max_pairs</STRONG> - 1),
- and two triples describing first background and then
- foreground colors. These parameters must be (Red,
+ <STRONG>o</STRONG> On an HP-like terminal, <STRONG>initp</STRONG> may give a capability
+ for changing a color-pair value. It will take seven
+ parameters; a color-pair number (0 to <STRONG>max_pairs</STRONG> - 1),
+ and two triples describing first background and then
+ foreground colors. These parameters must be (Red,
Green, Blue) or (Hue, Lightness, Saturation) depending
on <STRONG>hls</STRONG>.
- On some color terminals, colors collide with highlights.
+ On some color terminals, colors collide with highlights.
You can register these collisions with the <STRONG>ncv</STRONG> capability.
- This is a bit-mask of attributes not to be used when col-
- ors are enabled. The correspondence with the attributes
+ This is a bit-mask of attributes not to be used when col-
+ ors are enabled. The correspondence with the attributes
understood by <STRONG>curses</STRONG> is as follows:
<STRONG>Attribute</STRONG> <STRONG>Bit</STRONG> <STRONG>Decimal</STRONG> <STRONG>Set</STRONG> <STRONG>by</STRONG>
A_VERTICAL 14 16384 sgr1
A_ITALIC 15 32768 sitm
- For example, on many IBM PC consoles, the underline
- attribute collides with the foreground color blue and is
- not available in color mode. These should have an <STRONG>ncv</STRONG>
+ For example, on many IBM PC consoles, the underline
+ attribute collides with the foreground color blue and is
+ not available in color mode. These should have an <STRONG>ncv</STRONG>
capability of 2.
- SVr4 curses does nothing with <STRONG>ncv</STRONG>, ncurses recognizes it
+ SVr4 curses does nothing with <STRONG>ncv</STRONG>, ncurses recognizes it
and optimizes the output in favor of colors.
</PRE><H3><a name="h3-Miscellaneous">Miscellaneous</a></H3><PRE>
- If the terminal requires other than a null (zero) charac-
- ter as a pad, then this can be given as pad. Only the
- first character of the pad string is used. If the termi-
+ If the terminal requires other than a null (zero) charac-
+ ter as a pad, then this can be given as pad. Only the
+ first character of the pad string is used. If the termi-
nal does not have a pad character, specify npc. Note that
- ncurses implements the termcap-compatible <STRONG>PC</STRONG> variable;
- though the application may set this value to something
- other than a null, ncurses will test <STRONG>npc</STRONG> first and use
+ ncurses implements the termcap-compatible <STRONG>PC</STRONG> variable;
+ though the application may set this value to something
+ other than a null, ncurses will test <STRONG>npc</STRONG> first and use
napms if the terminal has no pad character.
- If the terminal can move up or down half a line, this can
- be indicated with <STRONG>hu</STRONG> (half-line up) and <STRONG>hd</STRONG> (half-line
+ If the terminal can move up or down half a line, this can
+ be indicated with <STRONG>hu</STRONG> (half-line up) and <STRONG>hd</STRONG> (half-line
down). This is primarily useful for superscripts and sub-
- scripts on hard-copy terminals. If a hard-copy terminal
- can eject to the next page (form feed), give this as <STRONG>ff</STRONG>
+ scripts on hard-copy terminals. If a hard-copy terminal
+ can eject to the next page (form feed), give this as <STRONG>ff</STRONG>
(usually control L).
- If there is a command to repeat a given character a given
- number of times (to save time transmitting a large number
- of identical characters) this can be indicated with the
- parameterized string <STRONG>rep</STRONG>. The first parameter is the
- character to be repeated and the second is the number of
- times to repeat it. Thus, tparm(repeat_char, 'x', 10) is
+ If there is a command to repeat a given character a given
+ number of times (to save time transmitting a large number
+ of identical characters) this can be indicated with the
+ parameterized string <STRONG>rep</STRONG>. The first parameter is the
+ character to be repeated and the second is the number of
+ times to repeat it. Thus, tparm(repeat_char, 'x', 10) is
the same as "xxxxxxxxxx".
- If the terminal has a settable command character, such as
- the TEKTRONIX 4025, this can be indicated with <STRONG>cmdch</STRONG>. A
+ If the terminal has a settable command character, such as
+ the TEKTRONIX 4025, this can be indicated with <STRONG>cmdch</STRONG>. A
prototype command character is chosen which is used in all
- capabilities. This character is given in the <STRONG>cmdch</STRONG> capa-
- bility to identify it. The following convention is sup-
- ported on some UNIX systems: The environment is to be
- searched for a <STRONG>CC</STRONG> variable, and if found, all occurrences
+ capabilities. This character is given in the <STRONG>cmdch</STRONG> capa-
+ bility to identify it. The following convention is sup-
+ ported on some UNIX systems: The environment is to be
+ searched for a <STRONG>CC</STRONG> variable, and if found, all occurrences
of the prototype character are replaced with the character
in the environment variable.
- Terminal descriptions that do not represent a specific
+ Terminal descriptions that do not represent a specific
kind of known terminal, such as <EM>switch</EM>, <EM>dialup</EM>, <EM>patch</EM>, and
- <EM>network</EM>, should include the <STRONG>gn</STRONG> (generic) capability so
- that programs can complain that they do not know how to
- talk to the terminal. (This capability does not apply to
- <EM>virtual</EM> terminal descriptions for which the escape
+ <EM>network</EM>, should include the <STRONG>gn</STRONG> (generic) capability so
+ that programs can complain that they do not know how to
+ talk to the terminal. (This capability does not apply to
+ <EM>virtual</EM> terminal descriptions for which the escape
sequences are known.)
- If the terminal has a "meta key" which acts as a shift
- key, setting the 8th bit of any character transmitted,
- this fact can be indicated with <STRONG>km</STRONG>. Otherwise, software
+ If the terminal has a "meta key" which acts as a shift
+ key, setting the 8th bit of any character transmitted,
+ this fact can be indicated with <STRONG>km</STRONG>. Otherwise, software
will assume that the 8th bit is parity and it will usually
- be cleared. If strings exist to turn this "meta mode" on
+ be cleared. If strings exist to turn this "meta mode" on
and off, they can be given as <STRONG>smm</STRONG> and <STRONG>rmm</STRONG>.
- If the terminal has more lines of memory than will fit on
- the screen at once, the number of lines of memory can be
- indicated with <STRONG>lm</STRONG>. A value of <STRONG>lm</STRONG>#0 indicates that the
+ If the terminal has more lines of memory than will fit on
+ the screen at once, the number of lines of memory can be
+ indicated with <STRONG>lm</STRONG>. A value of <STRONG>lm</STRONG>#0 indicates that the
number of lines is not fixed, but that there is still more
memory than fits on the screen.
If the terminal is one of those supported by the UNIX vir-
- tual terminal protocol, the terminal number can be given
+ tual terminal protocol, the terminal number can be given
as <STRONG>vt</STRONG>.
Media copy strings which control an auxiliary printer con-
nected to the terminal can be given as <STRONG>mc0</STRONG>: print the con-
- tents of the screen, <STRONG>mc4</STRONG>: turn off the printer, and <STRONG>mc5</STRONG>:
- turn on the printer. When the printer is on, all text
- sent to the terminal will be sent to the printer. It is
+ tents of the screen, <STRONG>mc4</STRONG>: turn off the printer, and <STRONG>mc5</STRONG>:
+ turn on the printer. When the printer is on, all text
+ sent to the terminal will be sent to the printer. It is
undefined whether the text is also displayed on the termi-
nal screen when the printer is on. A variation <STRONG>mc5p</STRONG> takes
one parameter, and leaves the printer on for as many char-
- acters as the value of the parameter, then turns the
- printer off. The parameter should not exceed 255. All
+ acters as the value of the parameter, then turns the
+ printer off. The parameter should not exceed 255. All
text, including <STRONG>mc4</STRONG>, is transparently passed to the
printer while an <STRONG>mc5p</STRONG> is in effect.
</PRE><H3><a name="h3-Glitches-and-Braindamage">Glitches and Braindamage</a></H3><PRE>
- Hazeltine terminals, which do not allow "~" characters to
+ Hazeltine terminals, which do not allow "~" characters to
be displayed should indicate <STRONG>hz</STRONG>.
Terminals which ignore a line-feed immediately after an <STRONG>am</STRONG>
wrap, such as the Concept and vt100, should indicate <STRONG>xenl</STRONG>.
- If <STRONG>el</STRONG> is required to get rid of standout (instead of
- merely writing normal text on top of it), <STRONG>xhp</STRONG> should be
+ If <STRONG>el</STRONG> is required to get rid of standout (instead of
+ merely writing normal text on top of it), <STRONG>xhp</STRONG> should be
given.
- Teleray terminals, where tabs turn all characters moved
- over to blanks, should indicate <STRONG>xt</STRONG> (destructive tabs).
- Note: the variable indicating this is now
- "dest_tabs_magic_smso"; in older versions, it was tel-
+ Teleray terminals, where tabs turn all characters moved
+ over to blanks, should indicate <STRONG>xt</STRONG> (destructive tabs).
+ Note: the variable indicating this is now
+ "dest_tabs_magic_smso"; in older versions, it was tel-
eray_glitch. This glitch is also taken to mean that it is
- not possible to position the cursor on top of a "magic
- cookie", that to erase standout mode it is instead neces-
+ not possible to position the cursor on top of a "magic
+ cookie", that to erase standout mode it is instead neces-
sary to use delete and insert line. The ncurses implemen-
tation ignores this glitch.
- The Beehive Superbee, which is unable to correctly trans-
- mit the escape or control C characters, has <STRONG>xsb</STRONG>, indicat-
- ing that the f1 key is used for escape and f2 for control
- C. (Only certain Superbees have this problem, depending
- on the ROM.) Note that in older terminfo versions, this
- capability was called "beehive_glitch"; it is now
+ The Beehive Superbee, which is unable to correctly trans-
+ mit the escape or control C characters, has <STRONG>xsb</STRONG>, indicat-
+ ing that the f1 key is used for escape and f2 for control
+ C. (Only certain Superbees have this problem, depending
+ on the ROM.) Note that in older terminfo versions, this
+ capability was called "beehive_glitch"; it is now
"no_esc_ctl_c".
- Other specific terminal problems may be corrected by
+ Other specific terminal problems may be corrected by
adding more capabilities of the form <STRONG>x</STRONG><EM>x</EM>.
</PRE><H3><a name="h3-Pitfalls-of-Long-Entries">Pitfalls of Long Entries</a></H3><PRE>
- Long terminfo entries are unlikely to be a problem; to
- date, no entry has even approached terminfo's 4096-byte
+ Long terminfo entries are unlikely to be a problem; to
+ date, no entry has even approached terminfo's 4096-byte
string-table maximum. Unfortunately, the termcap transla-
tions are much more strictly limited (to 1023 bytes), thus
- termcap translations of long terminfo entries can cause
+ termcap translations of long terminfo entries can cause
problems.
- The man pages for 4.3BSD and older versions of <STRONG>tgetent</STRONG>
- instruct the user to allocate a 1024-byte buffer for the
- termcap entry. The entry gets null-terminated by the
+ The man pages for 4.3BSD and older versions of <STRONG>tgetent</STRONG>
+ instruct the user to allocate a 1024-byte buffer for the
+ termcap entry. The entry gets null-terminated by the
termcap library, so that makes the maximum safe length for
- a termcap entry 1k-1 (1023) bytes. Depending on what the
- application and the termcap library being used does, and
- where in the termcap file the terminal type that <STRONG>tgetent</STRONG>
+ a termcap entry 1k-1 (1023) bytes. Depending on what the
+ application and the termcap library being used does, and
+ where in the termcap file the terminal type that <STRONG>tgetent</STRONG>
is searching for is, several bad things can happen.
- Some termcap libraries print a warning message or exit if
- they find an entry that's longer than 1023 bytes; others
- do not; others truncate the entries to 1023 bytes. Some
+ Some termcap libraries print a warning message or exit if
+ they find an entry that's longer than 1023 bytes; others
+ do not; others truncate the entries to 1023 bytes. Some
application programs allocate more than the recommended 1K
for the termcap entry; others do not.
Each termcap entry has two important sizes associated with
it: before "tc" expansion, and after "tc" expansion. "tc"
- is the capability that tacks on another termcap entry to
- the end of the current one, to add on its capabilities.
- If a termcap entry does not use the "tc" capability, then
+ is the capability that tacks on another termcap entry to
+ the end of the current one, to add on its capabilities.
+ If a termcap entry does not use the "tc" capability, then
of course the two lengths are the same.
- The "before tc expansion" length is the most important
- one, because it affects more than just users of that par-
- ticular terminal. This is the length of the entry as it
+ The "before tc expansion" length is the most important
+ one, because it affects more than just users of that par-
+ ticular terminal. This is the length of the entry as it
exists in /etc/termcap, minus the backslash-newline pairs,
- which <STRONG>tgetent</STRONG> strips out while reading it. Some termcap
- libraries strip off the final newline, too (GNU termcap
+ which <STRONG>tgetent</STRONG> strips out while reading it. Some termcap
+ libraries strip off the final newline, too (GNU termcap
does not). Now suppose:
- <STRONG>o</STRONG> a termcap entry before expansion is more than 1023
+ <STRONG>o</STRONG> a termcap entry before expansion is more than 1023
bytes long,
<STRONG>o</STRONG> and the application has only allocated a 1k buffer,
- <STRONG>o</STRONG> and the termcap library (like the one in BSD/OS 1.1
- and GNU) reads the whole entry into the buffer, no
- matter what its length, to see if it is the entry it
+ <STRONG>o</STRONG> and the termcap library (like the one in BSD/OS 1.1
+ and GNU) reads the whole entry into the buffer, no
+ matter what its length, to see if it is the entry it
wants,
- <STRONG>o</STRONG> and <STRONG>tgetent</STRONG> is searching for a terminal type that
- either is the long entry, appears in the termcap file
- after the long entry, or does not appear in the file
- at all (so that <STRONG>tgetent</STRONG> has to search the whole term-
+ <STRONG>o</STRONG> and <STRONG>tgetent</STRONG> is searching for a terminal type that
+ either is the long entry, appears in the termcap file
+ after the long entry, or does not appear in the file
+ at all (so that <STRONG>tgetent</STRONG> has to search the whole term-
cap file).
Then <STRONG>tgetent</STRONG> will overwrite memory, perhaps its stack, and
- probably core dump the program. Programs like telnet are
- particularly vulnerable; modern telnets pass along values
- like the terminal type automatically. The results are
- almost as undesirable with a termcap library, like SunOS
+ probably core dump the program. Programs like telnet are
+ particularly vulnerable; modern telnets pass along values
+ like the terminal type automatically. The results are
+ almost as undesirable with a termcap library, like SunOS
4.1.3 and Ultrix 4.4, that prints warning messages when it
- reads an overly long termcap entry. If a termcap library
- truncates long entries, like OSF/1 3.0, it is immune to
- dying here but will return incorrect data for the termi-
+ reads an overly long termcap entry. If a termcap library
+ truncates long entries, like OSF/1 3.0, it is immune to
+ dying here but will return incorrect data for the termi-
nal.
The "after tc expansion" length will have a similar effect
while searching.
In summary, a termcap entry that is longer than 1023 bytes
- can cause, on various combinations of termcap libraries
- and applications, a core dump, warnings, or incorrect
- operation. If it is too long even before "tc" expansion,
+ can cause, on various combinations of termcap libraries
+ and applications, a core dump, warnings, or incorrect
+ operation. If it is too long even before "tc" expansion,
it will have this effect even for users of some other ter-
- minal types and users whose TERM variable does not have a
+ minal types and users whose TERM variable does not have a
termcap entry.
When in -C (translate to termcap) mode, the <STRONG>ncurses</STRONG> imple-
mentation of <STRONG><A HREF="tic.1m.html">tic(1m)</A></STRONG> issues warning messages when the pre-
- tc length of a termcap translation is too long. The -c
- (check) option also checks resolved (after tc expansion)
+ tc length of a termcap translation is too long. The -c
+ (check) option also checks resolved (after tc expansion)
lengths.
</PRE><H3><a name="h3-Binary-Compatibility">Binary Compatibility</a></H3><PRE>
- It is not wise to count on portability of binary terminfo
- entries between commercial UNIX versions. The problem is
- that there are at least two versions of terminfo (under
+ It is not wise to count on portability of binary terminfo
+ entries between commercial UNIX versions. The problem is
+ that there are at least two versions of terminfo (under
HP-UX and AIX) which diverged from System V terminfo after
- SVr1, and have added extension capabilities to the string
- table that (in the binary format) collide with System V
+ SVr1, and have added extension capabilities to the string
+ table that (in the binary format) collide with System V
and XSI Curses extensions.
Searching for terminal descriptions in <STRONG>$HOME/.terminfo</STRONG> and
TERMINFO_DIRS is not supported by older implementations.
- Some SVr4 <STRONG>curses</STRONG> implementations, and all previous to
- SVr4, do not interpret the %A and %O operators in parame-
+ Some SVr4 <STRONG>curses</STRONG> implementations, and all previous to
+ SVr4, do not interpret the %A and %O operators in parame-
ter strings.
- SVr4/XPG4 do not specify whether <STRONG>msgr</STRONG> licenses movement
- while in an alternate-character-set mode (such modes may,
- among other things, map CR and NL to characters that do
- not trigger local motions). The <STRONG>ncurses</STRONG> implementation
- ignores <STRONG>msgr</STRONG> in <STRONG>ALTCHARSET</STRONG> mode. This raises the possi-
- bility that an XPG4 implementation making the opposite
- interpretation may need terminfo entries made for <STRONG>ncurses</STRONG>
+ SVr4/XPG4 do not specify whether <STRONG>msgr</STRONG> licenses movement
+ while in an alternate-character-set mode (such modes may,
+ among other things, map CR and NL to characters that do
+ not trigger local motions). The <STRONG>ncurses</STRONG> implementation
+ ignores <STRONG>msgr</STRONG> in <STRONG>ALTCHARSET</STRONG> mode. This raises the possi-
+ bility that an XPG4 implementation making the opposite
+ interpretation may need terminfo entries made for <STRONG>ncurses</STRONG>
to have <STRONG>msgr</STRONG> turned off.
- The <STRONG>ncurses</STRONG> library handles insert-character and insert-
+ The <STRONG>ncurses</STRONG> library handles insert-character and insert-
character modes in a slightly non-standard way to get bet-
- ter update efficiency. See the <STRONG>Insert/Delete</STRONG> <STRONG>Character</STRONG>
+ ter update efficiency. See the <STRONG>Insert/Delete</STRONG> <STRONG>Character</STRONG>
subsection above.
- The parameter substitutions for <STRONG>set_clock</STRONG> and <STRONG>dis-</STRONG>
- <STRONG>play_clock</STRONG> are not documented in SVr4 or the XSI Curses
+ The parameter substitutions for <STRONG>set_clock</STRONG> and <STRONG>dis-</STRONG>
+ <STRONG>play_clock</STRONG> are not documented in SVr4 or the XSI Curses
standard. They are deduced from the documentation for the
AT&T 505 terminal.
- Be careful assigning the <STRONG>kmous</STRONG> capability. The <STRONG>ncurses</STRONG>
- library wants to interpret it as <STRONG>KEY_MOUSE</STRONG>, for use by
- terminals and emulators like xterm that can return mouse-
+ Be careful assigning the <STRONG>kmous</STRONG> capability. The <STRONG>ncurses</STRONG>
+ library wants to interpret it as <STRONG>KEY_MOUSE</STRONG>, for use by
+ terminals and emulators like xterm that can return mouse-
tracking information in the keyboard-input stream.
X/Open Curses does not mention italics. Portable applica-
- tions must assume that numeric capabilities are signed
- 16-bit values. This includes the <EM>no</EM><STRONG>_</STRONG><EM>color</EM><STRONG>_</STRONG><EM>video</EM> (ncv)
- capability. The 32768 mask value used for italics with
- ncv can be confused with an absent or cancelled ncv. If
- italics should work with colors, then the ncv value must
+ tions must assume that numeric capabilities are signed
+ 16-bit values. This includes the <EM>no</EM><STRONG>_</STRONG><EM>color</EM><STRONG>_</STRONG><EM>video</EM> (ncv)
+ capability. The 32768 mask value used for italics with
+ ncv can be confused with an absent or cancelled ncv. If
+ italics should work with colors, then the ncv value must
be specified, even if it is zero.
- Different commercial ports of terminfo and curses support
- different subsets of the XSI Curses standard and (in some
+ Different commercial ports of terminfo and curses support
+ different subsets of the XSI Curses standard and (in some
cases) different extension sets. Here is a summary, accu-
rate as of October 1995:
<STRONG>o</STRONG> <STRONG>SVR4,</STRONG> <STRONG>Solaris,</STRONG> <STRONG>ncurses</STRONG> -- These support all SVr4 capa-
bilities.
- <STRONG>o</STRONG> <STRONG>SGI</STRONG> -- Supports the SVr4 set, adds one undocumented
+ <STRONG>o</STRONG> <STRONG>SGI</STRONG> -- Supports the SVr4 set, adds one undocumented
extended string capability (<STRONG>set_pglen</STRONG>).
- <STRONG>o</STRONG> <STRONG>SVr1,</STRONG> <STRONG>Ultrix</STRONG> -- These support a restricted subset of
- terminfo capabilities. The booleans end with
+ <STRONG>o</STRONG> <STRONG>SVr1,</STRONG> <STRONG>Ultrix</STRONG> -- These support a restricted subset of
+ terminfo capabilities. The booleans end with
<STRONG>xon_xoff</STRONG>; the numerics with <STRONG>width_status_line</STRONG>; and the
strings with <STRONG>prtr_non</STRONG>.
- <STRONG>o</STRONG> <STRONG>HP/UX</STRONG> -- Supports the SVr1 subset, plus the SVr[234]
- numerics <STRONG>num_labels</STRONG>, <STRONG>label_height</STRONG>, <STRONG>label_width</STRONG>, plus
+ <STRONG>o</STRONG> <STRONG>HP/UX</STRONG> -- Supports the SVr1 subset, plus the SVr[234]
+ numerics <STRONG>num_labels</STRONG>, <STRONG>label_height</STRONG>, <STRONG>label_width</STRONG>, plus
function keys 11 through 63, plus <STRONG>plab_norm</STRONG>, <STRONG>label_on</STRONG>,
- and <STRONG>label_off</STRONG>, plus some incompatible extensions in
+ and <STRONG>label_off</STRONG>, plus some incompatible extensions in
the string table.
<STRONG>o</STRONG> <STRONG>AIX</STRONG> -- Supports the SVr1 subset, plus function keys 11
through 63, plus a number of incompatible string table
extensions.
- <STRONG>o</STRONG> <STRONG>OSF</STRONG> -- Supports both the SVr4 set and the AIX exten-
+ <STRONG>o</STRONG> <STRONG>OSF</STRONG> -- Supports both the SVr4 set and the AIX exten-
sions.
</PRE><H2><a name="h2-AUTHORS">AUTHORS</a></H2><PRE>
- Zeyd M. Ben-Halim, Eric S. Raymond, Thomas E. Dickey.
+ Zeyd M. Ben-Halim, Eric S. Raymond, Thomas E. Dickey.
Based on pcurses by Pavel Curtis.
<STRONG><A HREF="infocmp.1m.html">infocmp(1m)</A></STRONG>, <STRONG><A HREF="captoinfo.1m.html">captoinfo(1m)</A></STRONG>, <STRONG><A HREF="infotocap.1m.html">infotocap(1m)</A></STRONG>, <STRONG><A HREF="toe.1m.html">toe(1m)</A></STRONG>,
<STRONG><A HREF="ncurses.3x.html">curses(3x)</A></STRONG>, <STRONG><A HREF="term.5.html">term(5)</A></STRONG>. <STRONG><A HREF="terminfo.5.html">terminfo(5)</A></STRONG>.
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
</PRE><H2><a name="h2-AUTHOR">AUTHOR</a></H2><PRE>
<STRONG><A HREF="tic.1m.html">tic(1m)</A></STRONG>, <STRONG><A HREF="infocmp.1m.html">infocmp(1m)</A></STRONG>, <STRONG><A HREF="captoinfo.1m.html">captoinfo(1m)</A></STRONG>, <STRONG><A HREF="infotocap.1m.html">infotocap(1m)</A></STRONG>,
<STRONG><A HREF="ncurses.3x.html">curses(3x)</A></STRONG>, <STRONG><A HREF="terminfo.5.html">terminfo(5)</A></STRONG>.
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
<STRONG><A HREF="clear.1.html">clear(1)</A></STRONG>, <STRONG>stty(1)</STRONG>, <STRONG><A HREF="tabs.1.html">tabs(1)</A></STRONG>, <STRONG><A HREF="tset.1.html">tset(1)</A></STRONG>, <STRONG><A HREF="terminfo.5.html">terminfo(5)</A></STRONG>,
<STRONG><A HREF="curs_termcap.3x.html">curs_termcap(3x)</A></STRONG>.
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
* sale, use or other dealings in this Software without prior written *
* authorization. *
****************************************************************************
- * @Id: tset.1,v 1.48 2017/01/14 20:55:07 tom Exp @
+ * @Id: tset.1,v 1.49 2017/04/16 21:30:15 tom Exp @
-->
<!DOCTYPE html PUBLIC "-//W3C//DTD HTML 4.01//EN">
<HTML>
<STRONG>csh(1)</STRONG>, <STRONG>sh(1)</STRONG>, <STRONG>stty(1)</STRONG>, <STRONG><A HREF="curs_terminfo.3x.html">curs_terminfo(3x)</A></STRONG>, <STRONG>tty(4)</STRONG>,
<STRONG><A HREF="terminfo.5.html">terminfo(5)</A></STRONG>, <STRONG>ttys(5)</STRONG>, <STRONG>environ(7)</STRONG>
- This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170401).
+ This describes <STRONG>ncurses</STRONG> version 6.0 (patch 20170422).
.\" authorization. *
.\"***************************************************************************
.\"
-.\" $Id: curs_addch.3x,v 1.38 2017/01/07 19:25:15 tom Exp $
+.\" $Id: curs_addch.3x,v 1.39 2017/04/17 00:14:02 tom Exp $
.TH curs_addch 3X ""
.de bP
.IP \(bu 4
.SS Adding characters
The \fBaddch\fR, \fBwaddch\fR, \fBmvaddch\fR and \fBmvwaddch\fR routines put
the character \fIch\fR into the given window at its current window position,
-which is then advanced. They are analogous to \fBputchar\fR in \fBstdio\fR(3).
+which is then advanced. They are analogous to \fBputchar\fR(3) in \fBstdio\fR(3).
If the advance is at the right margin:
.bP
The cursor automatically wraps to the beginning of the next line.
.\"***************************************************************************
-.\" Copyright (c) 1998-2006,2010 Free Software Foundation, Inc. *
+.\" Copyright (c) 1998-2010,2017 Free Software Foundation, Inc. *
.\" *
.\" Permission is hereby granted, free of charge, to any person obtaining a *
.\" copy of this software and associated documentation files (the *
.\" authorization. *
.\"***************************************************************************
.\"
-.\" $Id: curs_scanw.3x,v 1.17 2010/12/04 18:40:45 tom Exp $
+.\" $Id: curs_scanw.3x,v 1.18 2017/04/17 00:07:02 tom Exp $
.TH curs_scanw 3X ""
.SH NAME
\fBscanw\fR,
for \fBsscanf\fR(3). Fields which do not map to a variable in the \fIfmt\fR
field are lost.
.PP
-The \fBvwscanw\fR and \fBvw_scanw\fR routines are analogous to \fBvscanf\fR.
+The \fBvwscanw\fR and \fBvw_scanw\fR routines are analogous to \fBvscanf\fR(3).
They perform a \fBwscanw\fR using a variable argument list.
The third argument is a \fIva_list\fR,
a pointer to a list of arguments, as defined in \fB<stdarg.h>\fR.
.LP
Both XSI and The Single Unix Specification, Version 2 state that these
functions return ERR or OK.
-Since the underlying \fBscanf\fR can return the number of items scanned,
+Since the underlying \fBscanf\fR(3) can return the number of items scanned,
and the SVr4 code was documented to use this feature,
this is probably an editing error which was introduced in XSI,
rather than being done intentionally.
.\" authorization. *
.\"***************************************************************************
.\"
-.\" $Id: curs_scr_dump.3x,v 1.10 2017/01/07 19:25:15 tom Exp $
+.\" $Id: curs_scr_dump.3x,v 1.11 2017/04/17 00:41:24 tom Exp $
.TH curs_scr_dump 3X ""
.na
.hy 0
considered invalid "if the time-stamp of the tty is old" but do not define
"old".
.SH SEE ALSO
-\fBcurses\fR(3X), \fBcurs_initscr\fR(3X), \fBcurs_refresh\fR(3X),
-\fBcurs_util\fR(3X), \fBsystem\fR(3)
+\fBcurses\fR(3X),
+\fBcurs_initscr\fR(3X),
+\fBcurs_refresh\fR(3X),
+\fBcurs_util\fR(3X),
+\fBscr_dump\fR(5),
+\fBsystem\fR(3)
.\" authorization. *
.\"***************************************************************************
.\"
-.\" $Id: curs_util.3x,v 1.47 2017/02/18 16:43:03 tom Exp $
+.\" $Id: curs_util.3x,v 1.48 2017/04/22 14:05:14 tom Exp $
.TH curs_util 3X ""
.ie \n(.g .ds `` \(lq
.el .ds `` ``
The keycodes start at KEY_MAX, but are not guaranteed to be
the same value for different runs because user-defined codes are
merged from all terminal descriptions which have been loaded.
-The \fBuse_extended_names\fP function controls whether this data is
+The \fBuse_extended_names\fP(3X) function controls whether this data is
loaded when the terminal description is read by the library.
.SS nofilter/use_tioctl
.PP
# use or other dealings in this Software without prior written #
# authorization. #
##############################################################################
-# $Id: man_db.renames,v 1.50 2017/03/12 09:34:29 tom Exp $
+# $Id: man_db.renames,v 1.51 2017/04/21 23:57:09 tom Exp $
# Manual-page renamings for the man_db program
#
# Files:
mitem_userptr.3x menu_userptr.3menu
mitem_value.3x menu_value.3menu
mitem_visible.3x menu_visible.3menu
-new_pair.3x new_pair.3ncurses
ncurses.3x ncurses.3ncurses
+new_pair.3x new_pair.3ncurses
panel.3x panel.3curses
printf.3s printf.3
putc.3s putc.3
resizeterm.3x resizeterm.3ncurses
scanf.3s scanf.3
+scr_dump.5 scr_dump.5
system.3s system.3
tabs.1 tabs.1
term.5 term.5
toe.1m toe.1
tput.1 tput.1
tset.1 tset.1
-vprintf.3 vprintf.3
wresize.3x wresize.3ncurses
#
# Other:
system.3 system.3
regcomp.3x regcomp.3
regexec.3x regexec.3
+vprintf.3 vprintf.3
#
# The following are pages which may be generated depending on configuration:
adacurses-config.1 adacurses-config.1
-# $Id: manhtml.aliases,v 1.11 2017/03/17 23:51:03 tom Exp $
+# $Id: manhtml.aliases,v 1.12 2017/04/22 14:07:02 tom Exp $
#***************************************************************************
# Copyright (c) 2013-2016,2017 Free Software Foundation, Inc. *
# *
tputs(3X) curs_terminfo(3X)
use_env(3X) curs_util(3X)
use_default_colors(3X) default_colors(3X)
+use_extended_names(3X) curs_extend(3X)
vidputs(3X) curs_terminfo(3X)
wgetch(3X) curs_getch(3X)
-# $Id: manhtml.externs,v 1.5 2017/04/01 19:58:38 tom Exp $
+# $Id: manhtml.externs,v 1.9 2017/04/17 01:03:16 tom Exp $
# Items in this list will not be linked by man2html
#***************************************************************************
# Copyright (c) 2013,2017 Free Software Foundation, Inc. *
# authorization. *
#***************************************************************************
ADACURSES(1)
+COLOR_PAIR(1)
+COLOR_PAIR(2)
+COLOR_PAIR(3)
+atoi(3)
conflict(1)
csh(1)
ded(1)
environ(7)
+file(1)
getty(1)
nvi(1)
+od(1)
printf(3)
profile(5)
putc(3)
+putchar(3)
putwc(3)
read(2)
rogue(1)
tty(4)
ttys(5)
vprintf(3)
+vscanf(3)
wcwidth(3)
+write(2)
--- /dev/null
+.\"***************************************************************************
+.\" Copyright (c) 2017 Free Software Foundation, Inc. *
+.\" *
+.\" Permission is hereby granted, free of charge, to any person obtaining a *
+.\" copy of this software and associated documentation files (the *
+.\" "Software"), to deal in the Software without restriction, including *
+.\" without limitation the rights to use, copy, modify, merge, publish, *
+.\" distribute, distribute with modifications, sublicense, and/or sell *
+.\" copies of the Software, and to permit persons to whom the Software is *
+.\" furnished to do so, subject to the following conditions: *
+.\" *
+.\" The above copyright notice and this permission notice shall be included *
+.\" in all copies or substantial portions of the Software. *
+.\" *
+.\" THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS *
+.\" OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF *
+.\" MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. *
+.\" IN NO EVENT SHALL THE ABOVE COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, *
+.\" DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR *
+.\" OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR *
+.\" THE USE OR OTHER DEALINGS IN THE SOFTWARE. *
+.\" *
+.\" Except as contained in this notice, the name(s) of the above copyright *
+.\" holders shall not be used in advertising or otherwise to promote the *
+.\" sale, use or other dealings in this Software without prior written *
+.\" authorization. *
+.\"***************************************************************************
+.\"
+.\" $Id: scr_dump.5,v 1.9 2017/04/22 18:44:25 tom Exp $
+.TH scr_dump 5
+.ie \n(.g .ds `` \(lq
+.el .ds `` ``
+.ie \n(.g .ds '' \(rq
+.el .ds '' ''
+.de NS
+.ie \n(.sp
+.el .sp .5
+.ie \n(.in +4
+.el .in +2
+.nf
+.ft C \" Courier
+..
+.de NE
+.fi
+.ft R
+.in -4
+..
+.de bP
+.IP \(bu 4
+..
+.ds n 5
+.ds d @TERMINFO@
+.SH NAME
+scr_dump \- format of curses screen-dumps.
+.SH SYNOPSIS
+.B scr_dump
+.SH DESCRIPTION
+.PP
+The curses library provides applications with the ability to write the
+contents of a window to an external file using \fBscr_dump\fP or \fBputwin\fP,
+and read it back using \fBscr_restore\fP or \fBgetwin\fP.
+.PP
+The \fBputwin\fP and \fBgetwin\fP functions do the work;
+while \fBscr_dump\fP and \fBscr_restore\fP conveniently save and restore
+the whole screen, i.e., \fBstdscr\fP.
+.SS ncurses6
+.PP
+A longstanding implementation of screen-dump was
+revised with ncurses6 to remedy problems with the earlier approach:
+.bP
+A \*(``magic number\*('' is written to the beginning of the dump file,
+allowing applications (such as \fBfile\fP(1)) to recognize curses dump files.
+.IP
+Because ncurses6 uses a new format,
+that requires a new magic number
+was unused by other applications.
+This 16-bit number was unused:
+.NS
+0x8888 (octal \*(``\\210\\210\*('')
+.NE
+.IP
+but to be more certain, this 32-bit number was chosen:
+.NS
+0x88888888 (octal \*(``\\210\\210\\210\\210\*('')
+.NE
+.IP
+This is the pattern submitted to the maintainers of the \fBfile\fP program:
+.NS
+#
+# ncurses5 (and before) did not use a magic number,
+# making screen dumps "data".
+#
+# ncurses6 (2015) uses this format, ignoring byte-order
+0 string \\210\\210\\210\\210ncurses ncurses6 screen image
+#
+.NE
+.bP
+The screen dumps are written in textual form,
+so that internal data sizes are not directly related to the dump-format, and
+enabling the library to read dumps from either narrow- or wide-character-
+configurations.
+.IP
+The \fInarrow\fP library configuration holds characters and video attributes
+in a 32-bit \fBchtype\fP, while the \fIwide-character\fP library stores
+this information in the \fBcchar_t\fP structure, which is much larger than
+32-bits.
+.bP
+It is possible to read a screen dump into a terminal with a different
+screen-size,
+because the library truncates or fills the screen as necessary.
+.bP
+The ncurses6 \fBgetwin\fP reads the legacy screen dumps from ncurses5.
+.SS ncurses5 (legacy)
+.PP
+The screen-dump feature was added to ncurses in June 1995.
+While there were fixes and improvements in succeeding years,
+the basic scheme was unchanged:
+.bP
+The \fBWINDOW\fP structure was written in binary form.
+.bP
+The \fBWINDOW\fP structure refers to lines of data,
+which were written as an array of binary data following the \fBWINDOW\fP.
+.bP
+When \fBgetwin\fP restored the window,
+it would keep track of offsets into the array of line-data
+and adjust the \fBWINDOW\fP structure which was read back into memory.
+.PP
+This is similar to Unix SystemV,
+but does not write a \*(``magic number\*('' to identify the file format.
+.SH PORTABILITY
+.PP
+There is no standard format for \fBputwin\fP.
+This section gives a brief description of the existing formats.
+.SS X/Open Curses
+.PP
+Refer to \fIX/Open Curses, Issue 7\fP (2009).
+.PP
+X/Open's documentation for \fIenhanced curses\fP says only:
+.RS 3
+.PP
+The \fIgetwin(\ ) \fPfunction reads window-related data
+stored in the file by \fIputwin(\ )\fP.
+The function
+then creates and initializes a new window using that data.
+.PP
+The \fIputwin(\ )\fP function writes all data associated
+with \fIwin\fP into the \fIstdio\fP stream to which \fIfilep\fP
+points, using an \fBunspecified format\fP.
+This information can be retrieved later using \fIgetwin(\ )\fP.
+.RE
+.PP
+In the mid-1990s when the X/Open Curses document was written,
+there were still systems using older, less capable curses libraries
+(aside from the BSD curses library which was not relevant to X/Open
+because it did not meet the criteria for \fIbase curses\fP).
+The document explained the term \*(``enhanced\*('' as follows:
+.RS 3
+.bP
+Shading is used to identify \fIX/Open Enhanced Curses\fP material, relating to interfaces
+included to provide enhanced capabilities for applications originally written to be
+compiled on systems based on the UNIX operating system. Therefore, the features
+described may not be present on systems that conform to \fBXPG4 or to earlier XPG releases\fP.
+The relevant reference pages may provide additional or more specific portability warnings
+about use of the material.
+.RE
+.PP
+In the foregoing, emphasis was added to \fBunspecified format\fP
+and to \fBXPG4 or to earlier XPG releases\fP,
+for clarity.
+.SS Unix SystemV
+.PP
+Unix SystemV curses identified the file format by writing a
+\*(``magic number\*('' at the beginning of the dump.
+The \fBWINDOW\fP data and the lines of text follow, all in binary form.
+.PP
+The Solaris curses source has these definitions:
+.NS
+/* terminfo magic number */
+#define MAGNUM 0432
+
+/* curses screen dump magic number */
+#define SVR2_DUMP_MAGIC_NUMBER 0433
+#define SVR3_DUMP_MAGIC_NUMBER 0434
+.NE
+.PP
+That is, the feature was likely introduced in SVr2 (1984),
+and improved in SVr3 (1987).
+The Solaris curses source has no magic number for SVr4 (1989).
+Other operating systems (AIX and HPUX) use a magic number which would
+correspond to this definition:
+.NS
+/* curses screen dump magic number */
+#define SVR4_DUMP_MAGIC_NUMBER 0435
+.NE
+.PP
+That octal number in bytes is 001, 035.
+Because most Unix vendors use big-endian hardware,
+the magic number is written with the high-order byte first, e.g.,
+.NS
+\001\035
+.NE
+.PP
+After the magic number, the \fBWINDOW\fP structure and line-data are
+written in binary format.
+While the magic number used by the Unix systems can be seen using \fBod\fP(1),
+none of the Unix systems documents the format used for screen-dumps.
+.PP
+The Unix systems do not use identical formats.
+While collecting information for for this manual page,
+the \fIsavescreen\fP test-program
+produced dumps of different size
+(all on 64-bit hardware, on 40x80 screens):
+.bP
+AIX (51817 bytes)
+.bP
+HPUX (90093 bytes)
+.bP
+Solaris 10 (13273 bytes)
+.bP
+ncurses5 (12888 bytes)
+.SS Solaris
+.PP
+As noted above, Solaris curses has no magic number corresponding
+to SVr4 curses.
+This is odd since Solaris was the first operating system
+to pass the SVr4 guidelines.
+Solaris has two versions of curses:
+.bP
+The default curses library uses the SVr3 magic number.
+.bP
+There is an alternate curses library in \fB/usr/xpg4\fP.
+This uses a textual format with no magic number.
+.IP
+According to the copyright notice, the \fIxpg4\fP Solaris curses library was
+developed by MKS (Mortice Kern Systems) from 1990 to 1995.
+.IP
+Like ncurses6, there is a file-header with parameters.
+Unlike ncurses6, the contents of the window are written piecemeal,
+with coordinates and attributes for each chunk of text rather
+than writing the whole window from top to bottom.
+.SS PDCurses
+.PP
+PDCurses added support for screen dumps in version 2.7 (2005).
+Like Unix SystemV and ncurses5,
+it writes the \fBWINDOW\fP structure in binary,
+but begins the file with its three-byte identifier \*(``PDC\*('',
+followed by a one-byte version,
+e.g.,
+.NS
+ \*(``PDC\\001\*(''
+.NE
+.SS NetBSD
+.PP
+As of April 2017, NetBSD curses does not yet support screen dumps.
+.SH EXAMPLE
+.PP
+Given a simple program which writes text to the screen
+(and for the sake of example, limiting the screen-size to 10x20):
+.NS
+#include <curses.h>
+
+int
+main(void)
+{
+ putenv("LINES=10");
+ putenv("COLUMNS=20");
+ initscr();
+ start_color();
+ init_pair(1, COLOR_WHITE, COLOR_BLUE);
+ init_pair(2, COLOR_RED, COLOR_BLACK);
+ bkgd(COLOR_PAIR(1));
+ move(4, 5);
+ attron(A_BOLD);
+ addstr("Hello");
+ move(5, 5);
+ attroff(A_BOLD);
+ attrset(A_REVERSE | COLOR_PAIR(2));
+ addstr("World!");
+ refresh();
+ scr_dump("foo.out");
+ endwin();
+ return 0;
+}
+.NE
+.PP
+When run using ncurses6, the output looks like this:
+.NS
+\\210\\210\\210\\210ncurses 6.0.20170415
+_cury=5
+_curx=11
+_maxy=9
+_maxx=19
+_flags=14
+_attrs=\\{REVERSE|C2}
+flag=_idcok
+_delay=-1
+_regbottom=9
+_bkgrnd=\\{NORMAL|C1}\\s
+rows:
+1:\\{NORMAL|C1}\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s
+2:\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s
+3:\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s
+4:\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s
+5:\\s\\s\\s\\s\\s\\{BOLD}Hello\\{NORMAL}\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s
+6:\\s\\s\\s\\s\\s\\{REVERSE|C2}World!\\{NORMAL|C1}\\s\\s\\s\\s\\s\\s\\s\\s\\s
+7:\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s
+8:\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s
+9:\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s
+10:\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s\\s
+.NE
+.PP
+The first four octal escapes are actually nonprinting characters,
+while the remainder of the file is printable text.
+You may notice:
+.bP
+The actual color pair values are not written to the file.
+.bP
+All characters are shown in printable form; spaces are \*(``\\s\*('' to
+ensure they are not overlooked.
+.bP
+Attributes are written in escaped curly braces, e.g., \*(``\\{BOLD}\*('',
+and may include a color-pair (C1 or C2 in this example).
+.bP
+The parameters in the header are written out only if they are nonzero.
+When reading back, order does not matter.
+.ne 10
+.PP
+Running the same program with Solaris \fIxpg4\fP curses gives this dump:
+.NS
+MAX=10,20
+BEG=0,0
+SCROLL=0,10
+VMIN=1
+VTIME=0
+FLAGS=0x1000
+FG=0,0
+BG=0,0,
+0,0,0,1,
+0,19,0,0,
+1,0,0,1,
+1,19,0,0,
+2,0,0,1,
+2,19,0,0,
+3,0,0,1,
+3,19,0,0,
+4,0,0,1,
+4,5,0x20,0,Hello
+4,10,0,1,
+4,19,0,0,
+5,0,0,1,
+5,5,0x4,2,World!
+5,11,0,1,
+5,19,0,0,
+6,0,0,1,
+6,19,0,0,
+7,0,0,1,
+7,19,0,0,
+8,0,0,1,
+8,19,0,0,
+9,0,0,1,
+9,19,0,0,
+CUR=11,5
+.NE
+.PP
+Solaris \fBgetwin\fP requires that all parameters are present, and
+in the same order.
+The \fIxpg4\fP curses library does not know about the \fBbce\fP
+(back color erase) capability, and does not color the window background.
+.ne 10
+.PP
+On the other hand, the SVr4 curses library does know about the background
+color. However, its screen dumps are in binary.
+Here is the corresponding dump (using \*(``od -t x1\*(''):
+.NS
+0000000 1c 01 c3 d6 f3 58 05 00 0b 00 0a 00 14 00 00 00
+0000020 00 00 02 00 00 00 00 00 00 00 00 00 00 00 00 00
+0000040 00 00 b8 1a 06 08 cc 1a 06 08 00 00 09 00 10 00
+0000060 00 00 00 80 00 00 20 00 00 00 ff ff ff ff 00 00
+0000100 ff ff ff ff 00 00 00 00 20 80 00 00 20 80 00 00
+0000120 20 80 00 00 20 80 00 00 20 80 00 00 20 80 00 00
+*
+0000620 20 80 00 00 20 80 00 00 20 80 00 00 48 80 00 04
+0000640 65 80 00 04 6c 80 00 04 6c 80 00 04 6f 80 00 04
+0000660 20 80 00 00 20 80 00 00 20 80 00 00 20 80 00 00
+*
+0000740 20 80 00 00 20 80 00 00 20 80 00 00 57 00 81 00
+0000760 6f 00 81 00 72 00 81 00 6c 00 81 00 64 00 81 00
+0001000 21 00 81 00 20 80 00 00 20 80 00 00 20 80 00 00
+0001020 20 80 00 00 20 80 00 00 20 80 00 00 20 80 00 00
+*
+0001540 20 80 00 00 20 80 00 00 00 00 f6 d1 01 00 f6 d1
+0001560 08 00 00 00 40 00 00 00 00 00 00 00 00 00 00 07
+0001600 00 04 00 01 00 01 00 00 00 01 00 00 00 00 00 00
+0001620 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
+*
+0002371
+.NE
+.SH SEE ALSO
+.PP
+\fBcurs_scr_dump\fR(3X),
+\fBcurs_util\fR(3X).
+.SH AUTHORS
+.PP
+Thomas E. Dickey
+.br
+extended screen-dump format for ncurses 6.0 (2015)
+.sp
+Eric S. Raymond
+.br
+screen dump feature in ncurses 1.9.2d (1995)
.\" authorization. *
.\"***************************************************************************
.\"
-.\" $Id: terminfo.head,v 1.31 2017/03/06 09:58:14 tom Exp $
+.\" $Id: terminfo.head,v 1.32 2017/04/22 13:52:49 tom Exp $
.TH terminfo 5 "" "" "File Formats"
.ds n 5
.ds d @TERMINFO@
.de bP
.IP \(bu 4
..
+.de NS
+.ie \n(.sp
+.el .sp .5
+.ie \n(.in +4
+.el .in +2
+.nf
+.ft C \" Courier
+..
+.de NE
+.fi
+.ft R
+.in -4
+..
.SH NAME
terminfo \- terminal capability data base
.SH SYNOPSIS
-.\" $Id: terminfo.tail,v 1.78 2017/03/04 23:52:35 tom Exp $
+.\" $Id: terminfo.tail,v 1.85 2017/04/22 18:59:02 tom Exp $
.\" Beginning of terminfo.tail file
.\" This file is part of ncurses.
.\" See "terminfo.head" for copyright.
which it does not recognize,
it infers its type (boolean, number or string) from the syntax
and makes an extended table entry for that capability.
-The \fBuse_extended_names\fP function makes this information
+The \fBuse_extended_names\fP(3X) function makes this information
conditionally available to applications.
The ncurses library provides the data leaving most of the behavior
to applications:
ending at the next following \*(``,\*(''.
.PP
A number of escape sequences are provided in the string valued capabilities
-for easy encoding of characters there.
+for easy encoding of characters there:
+.bP
Both \fB\eE\fR and \fB\ee\fR
map to an \s-1ESCAPE\s0 character,
-\fB^x\fR maps to a control-x for any appropriate x, and the sequences
-\fB\en \el \er \et \eb \ef \es\fR give
-a newline, line-feed, return, tab, backspace, form-feed, and space.
+.bP
+\fB^x\fR maps to a control-x for any appropriate \fIx\fP, and
+.bP
+the sequences
+.RS 6
+.PP
+\fB\en\fP, \fB\el\fP, \fB\er\fP, \fB\et\fP, \fB\eb\fP, \fB\ef\fP, and \fB\es\fR
+.RE
+.IP
+produce
+.RS 6
+.PP
+\fInewline\fP, \fIline-feed\fP, \fIreturn\fP, \fItab\fP, \fIbackspace\fP, \fIform-feed\fP, and \fIspace\fP,
+.RE
+.IP
+respectively.
+.PP
+X/Open Curses does not say what \*(``appropriate \fIx\fP\*('' might be.
+In practice, that is a printable ASCII graphic character.
+The special case \*(``^?\*('' is interpreted as DEL (127).
+In all other cases, the character value is AND'd with 0x1f,
+mapping to ASCII control codes in the range 0 through 31.
+.PP
Other escapes include
.bP
\fB\e^\fR for \fB^\fR,
.IP
\fB\e0\fR will produce \e200, which does not terminate a string but behaves
as a null character on most terminals, providing CS7 is specified.
-See stty(1).
+See \fBstty\fP(1).
.IP
The reason for this quirk is to maintain binary compatibility of the
compiled terminfo files with other implementations,
.SS Line Graphics
.PP
Many terminals have alternate character sets useful for forms-drawing.
-Terminfo and \fBcurses\fR build in support for the drawing characters
+Terminfo and \fBcurses\fR built-in support for the drawing characters
supported by the VT100, with some characters from the AT&T 4410v1 added.
This alternate character set may be specified by the \fBacsc\fR capability.
.PP
.TS H
center expand;
-l l l l
-l l l l
-lw25 lw10 lw6 lw6.
+l l l l l
+l l l l l
+_ _ _ _ _
+lw25 lw10 lw6 lw6 lw6.
.\".TH
-\fBGlyph ACS Ascii VT100\fR
-\fBName Name Default Name\fR
-UK pound sign ACS_STERLING f }
-arrow pointing down ACS_DARROW v .
-arrow pointing left ACS_LARROW < ,
-arrow pointing right ACS_RARROW > +
-arrow pointing up ACS_UARROW ^ \-
-board of squares ACS_BOARD # h
-bullet ACS_BULLET o ~
-checker board (stipple) ACS_CKBOARD : a
-degree symbol ACS_DEGREE \e f
-diamond ACS_DIAMOND + `
-greater-than-or-equal-to ACS_GEQUAL > z
-greek pi ACS_PI * {
-horizontal line ACS_HLINE \- q
-lantern symbol ACS_LANTERN # i
-large plus or crossover ACS_PLUS + n
-less-than-or-equal-to ACS_LEQUAL < y
-lower left corner ACS_LLCORNER + m
-lower right corner ACS_LRCORNER + j
-not-equal ACS_NEQUAL ! |
-plus/minus ACS_PLMINUS # g
-scan line 1 ACS_S1 ~ o
-scan line 3 ACS_S3 \- p
-scan line 7 ACS_S7 \- r
-scan line 9 ACS_S9 \&_ s
-solid square block ACS_BLOCK # 0
-tee pointing down ACS_TTEE + w
-tee pointing left ACS_RTEE + u
-tee pointing right ACS_LTEE + t
-tee pointing up ACS_BTEE + v
-upper left corner ACS_ULCORNER + l
-upper right corner ACS_URCORNER + k
-vertical line ACS_VLINE | x
+\fBGlyph ACS Ascii VT100 VT100\fR
+\fBName Name Default Char Code\fR
+arrow pointing right ACS_RARROW > + 0x2b
+arrow pointing left ACS_LARROW < , 0x2c
+arrow pointing up ACS_UARROW ^ \- 0x2d
+arrow pointing down ACS_DARROW v . 0x2e
+solid square block ACS_BLOCK # 0 0x30
+diamond ACS_DIAMOND + ` 0x60
+checker board (stipple) ACS_CKBOARD : a 0x61
+degree symbol ACS_DEGREE \e f 0x66
+plus/minus ACS_PLMINUS # g 0x67
+board of squares ACS_BOARD # h 0x68
+lantern symbol ACS_LANTERN # i 0x69
+lower right corner ACS_LRCORNER + j 0x6a
+upper right corner ACS_URCORNER + k 0x6b
+upper left corner ACS_ULCORNER + l 0x6c
+lower left corner ACS_LLCORNER + m 0x6d
+large plus or crossover ACS_PLUS + n 0x6e
+scan line 1 ACS_S1 ~ o 0x6f
+scan line 3 ACS_S3 \- p 0x70
+horizontal line ACS_HLINE \- q 0x71
+scan line 7 ACS_S7 \- r 0x72
+scan line 9 ACS_S9 \&_ s 0x73
+tee pointing right ACS_LTEE + t 0x74
+tee pointing left ACS_RTEE + u 0x75
+tee pointing up ACS_BTEE + v 0x76
+tee pointing down ACS_TTEE + w 0x77
+vertical line ACS_VLINE | x 0x78
+less-than-or-equal-to ACS_LEQUAL < y 0x79
+greater-than-or-equal-to ACS_GEQUAL > z 0x7a
+greek pi ACS_PI * { 0x7b
+not-equal ACS_NEQUAL ! | 0x7c
+UK pound sign ACS_STERLING f } 0x7d
+bullet ACS_BULLET o ~ 0x7e
.TE
.PP
+A few notes apply to the table itself:
+.bP
+X/Open Curses incorrectly states that the mapping for \fIlantern\fP is
+uppercase \*(``I\*('' although Unix implementations use the
+lowercase \*(``i\*('' mapping.
+.bP
+The DEC VT100 implemented graphics using the alternate character set
+feature, temporarily switching \fImodes\fP and sending characters
+in the range 0x60 (96) to 0x7e (126).
+.bP
+The AT&T terminal added graphics characters outside that range.
+.PP
The best way to define a new device's graphics set is to add a column
to a copy of this table for your terminal, giving the character which
(when emitted between \fBsmacs\fR/\fBrmacs\fR switches) will be rendered
.\" authorization. *
.\"***************************************************************************
.\"
-.\" $Id: tset.1,v 1.48 2017/01/14 20:55:07 tom Exp $
+.\" $Id: tset.1,v 1.49 2017/04/16 21:30:15 tom Exp $
.TH @TSET@ 1 ""
.ie \n(.g .ds `` \(lq
.el .ds `` ``
terminal capability database
.SH SEE ALSO
.hy 0
-csh(1),
-sh(1),
-stty(1),
-curs_terminfo(3X),
-tty(4),
-terminfo(5),
-ttys(5),
-environ(7)
+\fBcsh\fP(1),
+\fBsh\fP(1),
+\fBstty\fP(1),
+\fBcurs_terminfo\fP(3X),
+\fBtty\fP(4),
+\fBterminfo\fP(5),
+\fBttys\fP(5),
+\fBenviron\fP(7)
.hy
.PP
This describes \fBncurses\fR
# Report bugs and new terminal descriptions to
# bug-ncurses@gnu.org
#
-# $Revision: 1.598 $
-# $Date: 2017/04/01 20:40:04 $
+# $Revision: 1.602 $
+# $Date: 2017/04/22 20:18:54 $
#
# The original header is preserved below for reference. It is noted that there
# is a "newer" version which differs in some cosmetic details (but actually
dumb|80-column dumb tty,
am,
cols#80,
- bel=^G, cr=^M, cud1=^J, ind=^J,
+ bel=^G, cr=\r, cud1=\n, ind=\n,
unknown|unknown terminal type,
gn, use=dumb,
lpr|printer|line printer,
OTbs, hc, os,
cols#132, lines#66,
- bel=^G, cr=^M, cub1=^H, cud1=^J, ff=^L, ind=^J,
+ bel=^G, cr=\r, cub1=^H, cud1=\n, ff=^L, ind=\n,
glasstty|classic glass tty interpreting ASCII control characters,
OTbs, am,
cols#80,
- bel=^G, clear=^L, cr=^M, cub1=^H, cud1=^J, ht=^I, kcub1=^H,
- kcud1=^J, nel=^M^J, .kbs=^H,
+ bel=^G, clear=^L, cr=\r, cub1=^H, cud1=\n, ht=^I, kcub1=^H,
+ kcud1=\n, nel=\r\n, .kbs=^H,
vanilla|dumb tty,
OTbs,
- bel=^G, cr=^M, cud1=^J, ind=^J,
+ bel=^G, cr=\r, cud1=\n, ind=\n,
# This is almost the same as "dumb", but with no prespecified width.
# DEL and ^C are hardcoded to act as kill characters.
# for compatibility with xterm -TD
9term|Plan9 terminal emulator for X,
am,
- OTnl=^J, bel=^G, cud1=^J,
+ OTnl=\n, bel=^G, cud1=\n,
#### ANSI.SYS/ISO 6429/ECMA-48 Capabilities
#
ansi+idl,
dl=\E[%p1%dM, il=\E[%p1%dL, use=ansi+idl1,
ansi+idc,
- dch1=\E[P, ich=\E[%p1%d@, ich1=\E[@, rmir=\E6, smir=\E6,
+ dch1=\E[P, ich=\E[%p1%d@, ich1=\E[@, rmir=\E[4l, smir=\E[4h,
ansi+arrows,
kbs=^H, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
khome=\E[H,
ansi77|ansi 3.64 standard 1977 version,
OTbs, am, mir,
cols#80, it#8, lines#24,
- bel=^G, clear=\E[;H\E[2J, cr=^M, csr=\E[%i%p1%d;%p2%dr,
+ bel=^G, clear=\E[;H\E[2J, cr=\r, csr=\E[%i%p1%d;%p2%dr,
cub1=^H, cud1=\E[B, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu1=\E[A, dch1=\E[P, dl1=\E[M$<5*/>, ed=\E[J, el=\E[K,
home=\E[H, ht=^I, il1=\E[L$<5*/>, ind=\ED, kbs=^H,
kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kf1=\EOP,
- kf2=\EOR, kf4=\EOS, khome=\E[H, nel=^M\ED, rc=\E8, ri=\EM,
+ kf2=\EOR, kf4=\EOS, khome=\E[H, nel=\r\ED, rc=\E8, ri=\EM,
rmir=\E[4l, rmso=\E[m, rmul=\E[m, sc=\E7, smir=\E[4h,
smso=\E[7m, smul=\E[4m,
pcansi-m|pcansi-mono|ibm-pc terminal programs claiming to be ansi (mono mode),
OTbs, am, mir, msgr,
cols#80, it#8, lines#24,
- bel=^G, cbt=\E[Z, clear=\E[H\E[J, cr=^M, cub1=\E[D,
+ bel=^G, cbt=\E[Z, clear=\E[H\E[J, cr=\r, cub1=\E[D,
cud1=\E[B, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH, cuu1=\E[A,
dch1=\E[P, dl1=\E[M, ed=\E[J, el=\E[K, home=\E[H, ht=^I,
- hts=\EH, il1=\E[L, ind=^J, kbs=^H, kcub1=\E[D, kcud1=\E[B,
+ hts=\EH, il1=\E[L, ind=\n, kbs=^H, kcub1=\E[D, kcud1=\E[B,
kcuf1=\E[C, kcuu1=\E[A, khome=\E[H, tbc=\E[3g,
use=klone+sgr-dumb,
pcansi-25-m|pcansi25m|ibm-pc terminal programs with 25 lines (mono mode),
# underline, and reverse, which won't matter much if the terminal
# can't do some of those. Padding is assumed to be zero, which
# shouldn't hurt since xon/xoff is assumed.
-ansi-generic|generic ansi standard terminal,
+ansi-generic|ansiterm|generic ansi standard terminal,
am, xon,
cols#80, lines#24, use=vanilla, use=ansi+csr, use=ansi+cup,
use=ansi+rca, use=ansi+erase, use=ansi+tabs,
cols#80, lines#25,
clear=\E[2J, cub1=^H, cud1=\E[B, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu1=\E[A, el=\E[k, home=\E[H,
- is2=\E[m\E[?7h, kcub1=^H, kcud1=^J, kcuf1=^L, kcuu1=^K,
+ is2=\E[m\E[?7h, kcub1=^H, kcud1=\n, kcuf1=^L, kcuu1=^K,
khome=^^, pfkey=\E[0;%p1%{58}%+%d;%p2"%s"p, rc=\E[u,
rmam=\E[?7l, sc=\E[s, smam=\E[?7h, u6=\E[%i%d;%dR,
u7=\E[6n, use=klone+color, use=klone+sgr8,
st52|st52-m|at|at-m|atari|atari-m|atari_st|atarist-m|Atari ST,
am, eo, mir, npc,
cols#80, it#8, lines#24,
- bel=^G, civis=\Ef, clear=\EE, cnorm=\Ee, cr=^M, cub1=\ED,
+ bel=^G, civis=\Ef, clear=\EE, cnorm=\Ee, cr=\r, cub1=\ED,
cud1=\EB, cuf1=\EC, cup=\EY%p1%{32}%+%c%p2%{32}%+%c,
cuu1=\EA, dl1=\EM, ed=\EJ, el=\EK, el1=\Eo, home=\EH, ht=^I,
- il1=\EL, ind=^J, is2=\Ev\Eq\Ee, kLFT=\Ed, kRIT=\Ec, kbs=^H,
- kcub1=\ED, kcud1=\EB, kcuf1=\EC, kcuu1=\EA, kdch1=\177,
+ il1=\EL, ind=\n, is2=\Ev\Eq\Ee, kLFT=\Ed, kRIT=\Ec, kbs=^H,
+ kcub1=\ED, kcud1=\EB, kcuf1=\EC, kcuu1=\EA, kdch1=^?,
kf1=\EP, kf10=\EY, kf11=\Ep, kf12=\Eq, kf13=\Er, kf14=\Es,
kf15=\Et, kf16=\Eu, kf17=\Ev, kf18=\Ew, kf19=\Ex, kf2=\EQ,
kf20=\Ey, kf3=\ER, kf4=\ES, kf5=\ET, kf6=\EU, kf7=\EV, kf8=\EW,
kf9=\EX, khlp=\EH, khome=\EE, kich1=\EI, knp=\Eb, kpp=\Ea,
- kund=\EK, nel=^M^J, rc=\Ek, rev=\Ep, ri=\EI, rmso=\Eq,
+ kund=\EK, nel=\r\n, rc=\Ek, rev=\Ep, ri=\EI, rmso=\Eq,
rs2=\Ev\Eq\Ee, sc=\Ej, sgr0=\Eq, smso=\Ep,
tw100|toswin vt100 window mgr,
eo, mir, msgr, xon,
acsc=++\,\,--..00II``aaffgghhjjkkllmmnnooppqqrrssttuuvvwwxxy
yzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, civis=\Ef,
- clear=\E[2J\E[H, cnorm=\Ee, cr=^M, csr=\E[%i%p1%d;%p2%dr,
+ clear=\E[2J\E[H, cnorm=\Ee, cr=\r, csr=\E[%i%p1%d;%p2%dr,
cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=\EB,
cuf=\E[%p1%dC, cuf1=\EC, cup=\E[%i%p1%d;%p2%dH,
cuu=\E[%p1%dA, cuu1=\EA, dch1=\Ea, dim=\E[2m, dl=\E[%p1%dM,
dl1=\E[M, ed=\E[J, el=\E[K, el1=\E[1K, home=\E[H, ht=^I,
- hts=\EH, ich=\E[%p1%d@, il1=\EL, ind=^J, is2=\E<\E)0, kbs=^H,
- kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA, kdch1=\177,
+ hts=\EH, ich=\E[%p1%d@, il1=\EL, ind=\n, is2=\E<\E)0, kbs=^H,
+ kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA, kdch1=^?,
kf1=\EOP, kf10=\EOY, kf11=\Ep, kf12=\Eq, kf13=\Er, kf14=\Es,
kf15=\Et, kf16=\Eu, kf17=\Ev, kf18=\Ew, kf19=\Ex, kf2=\EOQ,
kf20=\Ey, kf3=\EOR, kf4=\EOS, kf5=\EOT, kf6=\EOU, kf7=\EOV,
am, msgr,
cols#80, it#8, lines#30,
bel=^G, blink=\Er, bold=\EyA, civis=\Ef, clear=\EE,
- cnorm=\E. \Ee, cr=^M, cub1=^H, cud1=\EB, cuf1=\EC,
+ cnorm=\E. \Ee, cr=\r, cub1=^H, cud1=\EB, cuf1=\EC,
cup=\EY%p1%{32}%+%c%p2%{32}%+%c, cuu1=\EA, cvvis=\E.",
dim=\Em, dl1=\EM, ed=\EJ, el=\EK, home=\EH, ht=^I, il1=\EL,
ind=\n$<2*/>, kbs=^H, kcub1=\ED, kcud1=\EB, kcuf1=\EC,
- kcuu1=\EA, kdch1=\177, kf1=\EP, kf10=\EY, kf11=\Ep, kf12=\Eq,
+ kcuu1=\EA, kdch1=^?, kf1=\EP, kf10=\EY, kf11=\Ep, kf12=\Eq,
kf13=\Er, kf14=\Es, kf15=\Et, kf16=\Eu, kf17=\Ev, kf18=\Ew,
kf19=\Ex, kf2=\EQ, kf20=\Ey, kf3=\ER, kf4=\ES, kf5=\ET,
kf6=\EU, kf7=\EV, kf8=\EW, kf9=\EX, khlp=\EH, khome=\EE,
\331k\277l\332m\300n\305o\377p-q\304r-s_t+u+v+w+x\263y
\363z\362{\343|\366}\234~\371,
bel=^G, blink=\Er, bold=\EyA, civis=\Ef, clear=\EE,
- cnorm=\E. \Ee, cr=^M, cub1=^H, cud1=\EB, cuf1=\EC,
+ cnorm=\E. \Ee, cr=\r, cub1=^H, cud1=\EB, cuf1=\EC,
cup=\EY%p1%{32}%+%c%p2%{32}%+%c, cuu1=\EA, cvvis=\E.",
dim=\Em, dl1=\EM, ed=\EJ, el=\EK, home=\EH, ht=^I, il1=\EL,
ind=\n$<2*/>, kbs=^H, kcub1=\ED, kcud1=\EB, kcuf1=\EC,
- kcuu1=\EA, kdch1=\177, kf1=\EP, kf10=\EY, kf11=\Ep, kf12=\Eq,
+ kcuu1=\EA, kdch1=^?, kf1=\EP, kf10=\EY, kf11=\Ep, kf12=\Eq,
kf13=\Er, kf14=\Es, kf15=\Et, kf16=\Eu, kf17=\Ev, kf18=\Ew,
kf19=\Ex, kf2=\EQ, kf20=\Ey, kf3=\ER, kf4=\ES, kf5=\ET,
kf6=\EU, kf7=\EV, kf8=\EW, kf9=\EX, khlp=\EH, khome=\EE,
st52-old|Atari ST with VT52 emulation,
am, km,
cols#80, lines#25,
- bel=^G, civis=\Ef, clear=\EH\EJ, cnorm=\Ee, cr=^M, cub1=\ED,
+ bel=^G, civis=\Ef, clear=\EH\EJ, cnorm=\Ee, cr=\r, cub1=\ED,
cud1=\EB, cuf1=\EC, cup=\EY%p1%{32}%+%c%p2%{32}%+%c,
cuu1=\EA, dl1=\EM, ed=\EJ, el=\EK, home=\EH, ht=^I, il1=\EL,
- ind=^J, ka1=\E#7, ka3=\E#5, kb2=\E#9, kbs=^H, kc1=\E#1,
+ ind=\n, ka1=\E#7, ka3=\E#5, kb2=\E#9, kbs=^H, kc1=\E#1,
kc3=\E#3, kclr=\E#7, kcub1=\E#K, kcud1=\E#P, kcuf1=\E#M,
kcuu1=\E#H, kf0=\E#D, kf1=\E#;, kf2=\E#<, kf3=\E#=, kf4=\E#>,
kf5=\E#?, kf6=\E#@, kf7=\E#A, kf8=\E#B, kf9=\E#C, khome=\E#G,
- kil1=\E#R, kind=\E#2, kri=\E#8, lf0=f10, nel=^M^J, rc=\Ek,
+ kil1=\E#R, kind=\E#2, kri=\E#8, lf0=f10, nel=\r\n, rc=\Ek,
ri=\EI, rmcup=, rmso=\Eq, rs1=\Ez_\Eb@\EcA, sc=\Ej, sgr0=\Eq,
smcup=\Ee, smso=\Ep,
nsterm+7|AppKit Terminal.app v41+ basic capabilities w/ASCII charset,
am, bw, msgr, xenl, xon,
cols#80, it#8, lines#24,
- bel=^G, blink=\E[5m, bold=\E[1m, clear=\E[H\E[J, cr=^M,
+ bel=^G, blink=\E[5m, bold=\E[1m, clear=\E[H\E[J, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dim=\E[2m, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J, el=\E[K,
el1=\E[1K, home=\E[H, ht=^I, hts=\EH, il=\E[%p1%dL, il1=\E[L,
- ind=^J, invis=\E[8m, kbs=\177, kcub1=\EOD, kcud1=\EOB,
+ ind=\n, invis=\E[8m, kbs=^?, kcub1=\EOD, kcud1=\EOB,
kcuf1=\EOC, kcuu1=\EOA, kent=\EOM, rc=\E8, rev=\E[7m, ri=\EM,
rmam=\E[?7l, rmkx=\E[?1l\E>, rmso=\E[m, rmul=\E[m,
rs2=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, sc=\E7,
xnuppc+basic|Darwin PowerPC Console basic capabilities,
am, bce, mir, xenl,
it#8,
- bold=\E[1m, clear=\E[H\E[J, cr=^M, csr=\E[%i%p1%d;%p2%dr,
+ bold=\E[1m, clear=\E[H\E[J, cr=\r, csr=\E[%i%p1%d;%p2%dr,
cub=\E[%p1%dD, cub1=\E[D, cud=\E[%p1%dB, cud1=\E[B,
cuf=\E[%p1%dC, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu=\E[%p1%dA, cuu1=\E[A, dsl=\E]2;\007, ed=\E[J, el=\E[K,
- el1=\E[1K, home=\E[H, ht=^I, hts=\EH, ind=^J, kbs=\177,
+ el1=\E[1K, home=\E[H, ht=^I, hts=\EH, ind=\n, kbs=^?,
kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA, rc=\E8,
rev=\E[7m, ri=\EM, rmam=\E[?7l, rmkx=\E[?1l\E>, rmso=\E[m,
rmul=\E[m, rs2=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h,
beterm|BeOS Terminal,
am, eo, mir, msgr, xenl, xon,
colors#8, cols#80, it#8, lines#25, ncv#5, pairs#64,
- bel=^G, bold=\E[1m, clear=\E[H\E[J, cr=^M,
+ bel=^G, bold=\E[1m, clear=\E[H\E[J, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
ech=\E[%p1%dX, ed=\E[J, el=\E[K, el1=\E[1K, home=\E[H,
hpa=\E[%i%p1%dG, ht=^I, hts=\EH, ich=\E[%p1%d@, ich1=\E[@,
- il=\E[%p1%dL, il1=\E[L, ind=^J, kbs=^H, kcub1=\E[D,
+ il=\E[%p1%dL, il1=\E[L, ind=\n, kbs=^H, kcub1=\E[D,
kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kdch1=\E[3~,
kend=\E[4~, kf1=\E[11~, kf10=\E[20~, kf11=\E[21~,
kf12=\E[22~, kf2=\E[12~, kf3=\E[13~, kf4=\E[14~,
kf5=\E[15~, kf6=\E[16~, kf7=\E[17~, kf8=\E[18~, kf9=\E[19~,
khome=\E[1~, kich1=\E[2~, knp=\E[6~, kpp=\E[5~, kspd=^Z,
- nel=^M^J, op=\E[m, rc=\E8, rev=\E[7m, ri=\EM, rmir=\E[4l,
+ nel=\r\n, op=\E[m, rc=\E8, rev=\E[7m, ri=\EM, rmir=\E[4l,
rmkx=\E[?4l, rmso=\E[m, rmul=\E[24m, rs1=\Ec, sc=\E7,
setab=\E[4%p1%dm, setaf=\E[3%p1%dm,
setb=\E[%p1%{40}%+%cm, setf=\E[%p1%{30}%+%cm,
acsc=+\020\,\021-\030.^Y0\333`\004a\261f\370g\361h\260i
\316j\331k\277l\332m\300n\305o~p\304q\304r\304s_t\303u
\264v\301w\302x\263y\363z\362{\343|\330}\234~\376,
- bel=^G, clear=\E[H\E[J, cr=^M, csr=\E[%i%p1%d;%p2%dr,
- cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=^J,
+ bel=^G, clear=\E[H\E[J, cr=\r, csr=\E[%i%p1%d;%p2%dr,
+ cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=\n,
cuf=\E[%p1%dC, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu=\E[%p1%dA, cuu1=\E[A, dch=\E[%p1%dP, dch1=\E[P,
dim=\E[2m, dl=\E[%p1%dM, dl1=\E[M, ech=\E[%p1%dX, ed=\E[J,
el=\E[K, el1=\E[1K, flash=\E[?5h$<200/>\E[?5l, home=\E[H,
hpa=\E[%i%p1%dG, ht=^I, hts=\EH, ich=\E[%p1%d@, ich1=\E[@,
- il=\E[%p1%dL, il1=\E[L, ind=^J, kb2=\E[G, kbs=\177,
- kcbt=\E[Z, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
+ il=\E[%p1%dL, il1=\E[L, ind=\n, kb2=\E[G, kbs=^?, kcbt=\E[Z,
+ kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
kdch1=\E[3~, kend=\E[4~, kf1=\E[[A, kf10=\E[21~,
kf11=\E[23~, kf12=\E[24~, kf13=\E[25~, kf14=\E[26~,
kf15=\E[28~, kf16=\E[29~, kf17=\E[31~, kf18=\E[32~,
kf19=\E[33~, kf2=\E[[B, kf20=\E[34~, kf3=\E[[C, kf4=\E[[D,
kf5=\E[[E, kf6=\E[17~, kf7=\E[18~, kf8=\E[19~, kf9=\E[20~,
khome=\E[1~, kich1=\E[2~, kmous=\E[M, knp=\E[6~, kpp=\E[5~,
- kspd=^Z, nel=^M^J, rc=\E8, rev=\E[7m, ri=\EM, rmam=\E[?7l,
+ kspd=^Z, nel=\r\n, rc=\E8, rev=\E[7m, ri=\EM, rmam=\E[?7l,
rmir=\E[4l, rmso=\E[27m, rmul=\E[24m, rs1=\Ec\E]R, sc=\E7,
sgr=\E[0;10%?%p1%t;7%;%?%p2%t;4%;%?%p3%t;7%;%?%p4%t;5%;%?%p5
%t;2%;%?%p6%t;1%;%?%p9%t;11%;m,
am, bce,
colors#8, cols#80, lines#24, pairs#64,
acsc=aajjkkllmmqqttuuxx, bold=\E[1m, civis=\E[?25l,
- clear=\E[H\E[2J, cnorm=\E[?25h, cr=^M, cub1=^H, cud1=^J,
- cup=\E[%i%p1%d;%p2%dH, ed=\E[J, el=\E[K, home=\E[H, ind=^J,
- kb2=\E[G, kbs=\177, kcbt=\E[Z, kcub1=\E[D, kcud1=\E[B,
+ clear=\E[H\E[2J, cnorm=\E[?25h, cr=\r, cub1=^H, cud1=\n,
+ cup=\E[%i%p1%d;%p2%dH, ed=\E[J, el=\E[K, home=\E[H, ind=\n,
+ kb2=\E[G, kbs=^?, kcbt=\E[Z, kcub1=\E[D, kcud1=\E[B,
kcuf1=\E[C, kcuu1=\E[A, kdch1=\E[3~, kend=\E[4~, kf1=\E[[A,
kf10=\E[21~, kf11=\E[23~, kf12=\E[24~, kf13=\E[25~,
kf14=\E[26~, kf15=\E[28~, kf16=\E[29~, kf17=\E[31~,
kf18=\E[32~, kf19=\E[33~, kf2=\E[[B, kf20=\E[34~,
kf3=\E[[C, kf4=\E[[D, kf5=\E[[E, kf6=\E[17~, kf7=\E[18~,
kf8=\E[19~, kf9=\E[20~, khome=\E[1~, kich1=\E[2~,
- kmous=\E[M, knp=\E[6~, kpp=\E[5~, kspd=^Z, nel=^M^J,
+ kmous=\E[M, knp=\E[6~, kpp=\E[5~, kspd=^Z, nel=\r\n,
op=\E[49m\E[39m, rev=\E[7m, ri=\EM, rmacs=^O, rmso=\E[27m,
rmul=\E[24m, setab=\E[4%p1%dm, setaf=\E[3%p1%dm,
sgr0=\E[0m, smacs=^N, smso=\E[7m, smul=\E[4m,
mach|Mach Console,
am, km,
cols#80, it#8, lines#25,
- bel=^G, blink=\E[5m, bold=\E[1m, clear=\Ec, cr=^M,
- cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=^J,
+ bel=^G, blink=\E[5m, bold=\E[1m, clear=\Ec, cr=\r,
+ cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=\n,
cuf=\E[%p1%dC, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu=\E[%p1%dA, cuu1=\E[A, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J,
- el=\E[K, home=\E[H, ht=^I, il=\E[%p1%dL, il1=\E[L, ind=^J,
- kbs=\177, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
+ el=\E[K, home=\E[H, ht=^I, il=\E[%p1%dL, il1=\E[L, ind=\n,
+ kbs=^?, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
kdch1=\E[9, kend=\E[Y, kf1=\EOP, kf10=\EOY, kf2=\EOQ,
kf3=\EOR, kf4=\EOS, kf5=\EOT, kf6=\EOU, kf7=\EOV, kf8=\EOW,
kf9=\EOX, khome=\E[H, kich1=\E[@, kll=\E[F, knp=\E[U,
acsc=++\,\,--..00``aaffgghhiijjkkllmmnnooppqqrrssttuuvvwwxxy
yzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z, civis=\E[?25l,
- clear=\Ec, cnorm=\E[?25h, cr=^M, csr=\E[%i%p1%d;%p2%dr,
+ clear=\Ec, cnorm=\E[?25h, cr=\r, csr=\E[%i%p1%d;%p2%dr,
cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=\E[B,
cuf=\E[%p1%dC, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu=\E[%p1%dA, cuu1=\E[A, cvvis=\E[34l, dch=\E[%p1%dP,
ech=\E[%p1%dX, ed=\E[J, el=\E[K, el1=\E[1K, flash=\Eg,
home=\E[H, hpa=\E[%i%p1%dG, ht=^I, ich=\E[%p1%d@,
il=\E[%p1%dL, il1=\E[L, ind=\E[S, indn=\E[%p1%dS,
- invis=\E[8m, kb2=\E[G, kbs=\177, kcbt=\E[Z, kcub1=\EOD,
+ invis=\E[8m, kb2=\E[G, kbs=^?, kcbt=\E[Z, kcub1=\EOD,
kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA, kdch1=\E[3~,
kend=\E[4~, kf1=\EOP, kf10=\E[21~, kf11=\E[23~,
kf12=\E[24~, kf13=\E[25~, kf14=\E[26~, kf15=\E[28~,
kf2=\EOQ, kf20=\E[34~, kf3=\EOR, kf4=\EOS, kf5=\E[15~,
kf6=\E[17~, kf7=\E[18~, kf8=\E[19~, kf9=\E[20~,
khome=\E[1~, kich1=\E[2~, kmous=\E[M, knp=\E[6~, kpp=\E[5~,
- kspd=^Z, nel=^M^J, op=\E[39;49m, rc=\E8, rev=\E[7m, ri=\E[T,
+ kspd=^Z, nel=\r\n, op=\E[39;49m, rc=\E8, rev=\E[7m, ri=\E[T,
rin=\E[%p1%dT, ritm=\E[23m, rmacs=\E[10m, rmir=\E[4l,
rmso=\E[27m, rmul=\E[24m, rs1=\EM\E[?1000l, sc=\E7,
setab=\E[4%p1%dm, setaf=\E[3%p1%dm,
acsc=O\333a\261j\331k\277l\332m\300n\305o\337q\304s\334t
\303u\264v\301w\302x\263,
bel=^G, blink=\E{, bold=\E<, civis=\Ey0, clear=\EH\EJ,
- cnorm=\Ey1, cr=^M, cub1=^H, cud1=^J, cuf1=\EC,
+ cnorm=\Ey1, cr=\r, cub1=^H, cud1=\n, cuf1=\EC,
cup=\EY%p1%{32}%+%c%p2%{32}%+%c, cuu1=\EA, cvvis=\Ey2,
dch1=\Ef, dl1=\EF, ed=\EJ, el=\EK, home=\EH, ht=^I, ich1=\Ee,
- il1=\EE, ind=^J, kBEG=\377\356, kCAN=\377\263,
+ il1=\EE, ind=\n, kBEG=\377\356, kCAN=\377\263,
kCMD=\377\267, kCPY=\377\363, kCRT=\377\364,
kDL=\377\366, kEND=\377\301, kEOL=\377\311,
kEXT=\377\367, kFND=\377\370, kHLP=\377\371,
colors#8, cols#80, it#8, lines#25, ncv#19, pairs#64, wsl#80,
acsc=Oa``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z, civis=\E[?25l,
- clear=\E[2J\E[H, cnorm=\E[?25h\E[?12l, cr=^M,
+ clear=\E[2J\E[H, cnorm=\E[?25h\E[?12l, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=\E[D,
cud=\E[%p1%dB, cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH$<5>, cuu=\E[%p1%dA, cuu1=\E[A,
hts=\EH, ich=\E[%p1%d@, ich1=\E[@, il=\E[%p1%dL, il1=\E[L,
ind=\E[S, indn=\E[%p1%dS, invis=\E[8m, kbeg=\E[E, kbs=^H,
kcbt=\E[Z, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
- kdch1=\177, kend=\E[F, kf1=\E[M, kf10=\E[V, kf11=\E[W,
+ kdch1=^?, kend=\E[F, kf1=\E[M, kf10=\E[V, kf11=\E[W,
kf12=\E[X, kf13=\E[Y, kf15=\E[a, kf16=\E[b, kf17=\E[c,
kf18=\E[d, kf19=\E[e, kf2=\E[N, kf20=\E[f, kf21=\E[g,
kf22=\E[h, kf23=\E[i, kf24=\E[j, kf25=\E[k, kf26=\E[l,
am,
cols#80, it#8, lines#40,
bel=^G, bold=\E[1m, clear=\E[H\E[2J,
- cnorm=\E[9/y\E[12/y\E[=6l, cr=^M, cub=\E[%p1%dD,
- cub1=\E[D, cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC,
+ cnorm=\E[9/y\E[12/y\E[=6l, cr=\r, cub=\E[%p1%dD,
+ cub1=\E[D, cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC,
cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA,
cuu1=\E[A, cvvis=\E[10/y\E[=1h\E[=2l\E[=6h,
dl=\E[%p1%dM, dl1=\E[M, ed=\E[J, el=\E[K, el1=\E[1K,
is2=\E[?1l\E>\E[?7h\E[100g\E[0m\E7\E[r\E8, kDC=\E[P,
kEND=\E[147q, kHOM=\E[143q, kLFT=\E[158q, kPRT=\E[210q,
kRIT=\E[167q, kSPD=\E[218q, kbs=^H, kcbt=\E[Z, kcub1=\E[D,
- kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kdch1=\177,
- kend=\E[146q, kent=^M, kf1=\E[001q, kf10=\E[010q,
- kf11=\E[011q, kf12=\E[012q, kf2=\E[002q, kf3=\E[003q,
- kf4=\E[004q, kf5=\E[005q, kf6=\E[006q, kf7=\E[007q,
- kf8=\E[008q, kf9=\E[009q, khome=\E[H, kich1=\E[139q,
- knp=\E[154q, kpp=\E[150q, kprt=\E[209q, krmir=\E[146q,
- kspd=\E[217q, nel=\EE, pfkey=\EP101;%p1%d.y%p2%s\E\\,
- rc=\E8, rev=\E[7m, ri=\EM, rmam=\E[?7l, rmso=\E[m, rmul=\E[m,
- sc=\E7, sgr0=\E[m, smam=\E[?7h, smso=\E[1;7m, smul=\E[4m,
+ kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kdch1=^?, kend=\E[146q,
+ kent=\r, kf1=\E[001q, kf10=\E[010q, kf11=\E[011q,
+ kf12=\E[012q, kf2=\E[002q, kf3=\E[003q, kf4=\E[004q,
+ kf5=\E[005q, kf6=\E[006q, kf7=\E[007q, kf8=\E[008q,
+ kf9=\E[009q, khome=\E[H, kich1=\E[139q, knp=\E[154q,
+ kpp=\E[150q, kprt=\E[209q, krmir=\E[146q, kspd=\E[217q,
+ nel=\EE, pfkey=\EP101;%p1%d.y%p2%s\E\\, rc=\E8,
+ rev=\E[7m, ri=\EM, rmam=\E[?7l, rmso=\E[m, rmul=\E[m, sc=\E7,
+ sgr0=\E[m, smam=\E[?7h, smso=\E[1;7m, smul=\E[4m,
tbc=\E[3g,
iris-ansi-ap|IRIS ANSI in application-keypad mode,
is2=\E[?1l\E=\E[?7h, kent=\EOM, kf10=\E[010q,
# CSI ? 5 h Reverse Video (DECSCNM).
#
pccon+keys|OpenBSD PC keyboard keys,
- kbs=\177, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
- kdch1=\E[3~, kend=\E[8~, kent=^M, kf1=\E[11~, kf10=\E[21~,
+ kbs=^?, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
+ kdch1=\E[3~, kend=\E[8~, kent=\r, kf1=\E[11~, kf10=\E[21~,
kf11=\E[23~, kf12=\E[24~, kf13=\E[25~, kf14=\E[26~,
kf15=\E[28~, kf16=\E[29~, kf17=\E[31~, kf18=\E[32~,
kf19=\E[33~, kf2=\E[12~, kf20=\E[34~, kf21=\E[35~,
pccon+base|base capabilities for OpenBSD PC console,
am, km, mc5i, msgr, npc, nxon, xenl, xon,
cols#80, it#8, lines#24,
- bel=^G, bold=\E[1m, clear=\E[H\E[J, cr=^M, cub1=^H, cud1=^J,
+ bel=^G, bold=\E[1m, clear=\E[H\E[J, cr=\r, cub1=^H, cud1=\n,
cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl1=\E[M, ech=\E[%p1%dX, ed=\E[J,
el=\E[K, el1=\E[1K, home=\E[H, ht=^I, hts=\EH, ich=\E[%p1%d@,
acsc=++\,\,--..00``aaffgghhiijjkkllmmnnooppqqrrssttuuvvwwxxy
yzz~~,
bel=^G, blink=\E[5m, bold=\E[1m, civis=\E[?25l,
- clear=\E[H\E[J, cnorm=\E[?25h, cr=^M,
+ clear=\E[H\E[J, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
cud=\E[%p1%dB, cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J,
el=\E[K, el1=\E[1K, home=\E[H, ht=^I, hts=\EH, ich=\E[%p1%d@,
il=\E[%p1%dL, il1=\E[L, ind=\ED, indn=\E[%p1%dS,
- is1=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, kbs=\177,
+ is1=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, kbs=^?,
kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kdch1=\E[3~, kf1=\E[17~, kf2=\E[18~, kf3=\E[19~,
kf4=\E[20~, kf5=\E[21~, kf6=\E[23~, kf7=\E[24~, kf8=\E[25~,
cols#80, it#8, lines#30,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m$<2>, bold=\E[1m$<2>,
- clear=\E[H\E[J$<50>, cr=^M, csr=\E[%i%p1%d;%p2%dr,
- cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=^J,
+ clear=\E[H\E[J$<50>, cr=\r, csr=\E[%i%p1%d;%p2%dr,
+ cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=\n,
cuf=\E[%p1%dC, cuf1=\E[C$<2>,
cup=\E[%i%p1%d;%p2%dH$<5>, cuu=\E[%p1%dA,
cuu1=\E[A$<2>, ed=\E[J$<50>, el=\E[K$<3>, el1=\E[1K$<3>,
- enacs=\E(B\E)0, home=\E[H, ht=^I, hts=\EH, ind=^J,
+ enacs=\E(B\E)0, home=\E[H, ht=^I, hts=\EH, ind=\n,
invis=\E[8m$<2>, ka1=\E[q, ka3=\E[s, kb2=\E[r, kbs=^H,
kc1=\E[p, kc3=\E[n, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C,
kcuu1=\E[A, kent=\E[M, kf0=\E[y, kf1=\E[P, kf10=\E[x,
ofcons|DNARD OpenFirmware console,
bw,
cols#80, lines#30,
- bel=^G, blink=\2335m, bold=\2331m, clear=^L, cr=^M,
+ bel=^G, blink=\2335m, bold=\2331m, clear=^L, cr=\r,
cub=\233%p1%dD, cub1=\233D, cud=\233%p1%dB, cud1=\233B,
cuf=\233%p1%dC, cuf1=\233C, cup=\233%i%p1%d;%p2%dH,
cuu=\233%p1%dA, cuu1=\233A, dch=\233%p1%dP, dch1=\233P,
dim=\2332m, dl=\233%p1%dM, dl1=\233M, ed=\233J, el=\233K,
flash=^G, ht=^I, ich=\233%p1%d@, ich1=\233@, il=\233%p1%dL,
- il1=\233L, ind=^J, invis=\2338m, kbs=^H, kcub1=\233D,
+ il1=\233L, ind=\n, invis=\2338m, kbs=^H, kcub1=\233D,
kcud1=\233B, kcuf1=\233C, kcuu1=\233A, kdch1=\233P,
kf1=\2330P, kf10=\2330M, kf2=\2330Q, kf3=\2330W,
kf4=\2330x, kf5=\2330t, kf6=\2330u, kf7=\2330q, kf8=\2330r,
- kf9=\2330p, knp=\233/, kpp=\233?, nel=^M^J, rev=\2337m,
+ kf9=\2330p, knp=\233/, kpp=\233?, nel=\r\n, rev=\2337m,
rmso=\2330m, rmul=\2330m,
sgr=\2330%?%p6%t;1%;%?%p2%t;4%;%?%p4%t;5%;%?%p5%t2%;%?%p7%t8
%;%?%p1%p3%|%t;7%;m,
# Background does not change in menu 11.6.9 (SGR 22-27)
# None of the xterm special features tests work
netbsd6|NetBSD wscons in 25 line DEC VT100 mode,
- kbs=\177, use=wsvt25,
+ kbs=^?, use=wsvt25,
# `rasterconsole' provided by 4.4BSD, NetBSD and OpenBSD on SPARC, and
# DECstation/pmax.
OTbs, OTpt, am, bce, bw, eo, km, msgr, npc,
colors#8, cols#80, it#8, lines#18, pairs#64,
bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z, clear=\E[H\E[J,
- cr=^M, csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
+ cr=\r, csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
cud=\E[%p1%dB, cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dim=\E[30;1m, dl=\E[%p1%dM,
home=\E[H, hpa=\E[%i%p1%d`, ht=^I, ich=\E[%p1%d@,
ich1=\E[@, il=\E[%p1%dL, il1=\E[L, ind=\E[S,
indn=\E[%p1%dS, kb2=\E[E, kbs=^H, kcbt=\E[Z, kcub1=\E[D,
- kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kdch1=\177, kend=\E[F,
+ kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kdch1=^?, kend=\E[F,
kf1=\E[M, kf10=\E[V, kf11=\E[W, kf12=\E[X, kf2=\E[N,
kf3=\E[O, kf4=\E[P, kf5=\E[Q, kf6=\E[R, kf7=\E[S, kf8=\E[T,
kf9=\E[U, khome=\E[H, kich1=\E[L, knp=\E[G, kpp=\E[I,
am, bce, bw, eo, msgr, npc,
colors#8, cols#80, it#8, lines#25, ncv#21, pairs#64,
bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z, clear=\E[H\E[J,
- cnorm=\E[=0C, cr=^M, cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB,
+ cnorm=\E[=0C, cr=\r, cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB,
cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
cvvis=\E[=1C, dch=\E[%p1%dP, dch1=\E[P, dim=\E[30;1m,
home=\E[H, hpa=\E[%i%p1%d`, ht=^I, ich=\E[%p1%d@,
ich1=\E[@, il=\E[%p1%dL, il1=\E[L, ind=\E[S,
indn=\E[%p1%dS, kb2=\E[E, kbs=^H, kcbt=\E[Z, kcub1=\E[D,
- kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kdch1=\177, kend=\E[F,
+ kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kdch1=^?, kend=\E[F,
kf1=\E[M, kf10=\E[V, kf11=\E[W, kf12=\E[X, kf13=\E[Y,
kf14=\E[Z, kf15=\E[a, kf16=\E[b, kf17=\E[c, kf18=\E[d,
kf19=\E[e, kf2=\E[N, kf20=\E[f, kf21=\E[g, kf22=\E[h,
\371,
use=cons25w,
cons25-debian|freebsd console with debian backspace (25-line ansi mode),
- kbs=\177, kdch1=\E[3~, use=cons25,
+ kbs=^?, kdch1=\E[3~, use=cons25,
cons25-m|ansis-mono|ansi80x25-mono|freebsd console (25-line mono ansi mode),
colors@, pairs@,
bold@, dim@, op@, rmul=\E[m, setab@, setaf@,
\304t\303u\264v\301w\302x\263y\363z\362~\371,
civis=\E[?25l, cnorm=\E[?25h, cvvis@, hpa=\E[%i%p1%dG,
hts=\EH, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
- kdch1=\E[3~, kend=\E[F, kent=^M, kf1=\EOP, kf10=\E[21~,
+ kdch1=\E[3~, kend=\E[F, kent=\r, kf1=\EOP, kf10=\E[21~,
kf11=\E[23~, kf12=\E[24~, kf2=\EOQ, kf3=\EOR, kf4=\EOS,
kf5=\E[15~, kf6=\E[17~, kf7=\E[18~, kf8=\E[19~, kf9=\E[20~,
khome=\E[H, kich1=\E[2~, knp=\E[6~, kpp=\E[5~, rmir=\E[4l,
oldpc3|oldibmpc3|old IBM PC BSD/386 Console,
OTbs, km,
lines#25,
- bel=^G, bold=\E[=15F, cr=^M, cud1=^J, dim=\E[=8F, dl1=\E[M,
- ht=^I, il1=\E[L, ind=^J, kbs=^H, kcub1=\E[D, kcud1=\E[B,
+ bel=^G, bold=\E[=15F, cr=\r, cud1=\n, dim=\E[=8F, dl1=\E[M,
+ ht=^I, il1=\E[L, ind=\n, kbs=^H, kcub1=\E[D, kcud1=\E[B,
kcuf1=\E[C, kcuu1=\E[A, khome=\E[H, kich1=\E[L, kll=\E[F,
- knp=\E[G, kpp=\E[I, nel=^M^J, sgr0=\E[=R,
+ knp=\E[G, kpp=\E[I, nel=\r\n, sgr0=\E[=R,
# Description of BSD/OS console emulator in version 1.1, 2.0, 2.1
# Note, the emulator supports many of the additional console features
bsdos-pc-m|bsdos-pc-mono|BSD/OS PC console mono,
OTbs, am, eo, km, xon,
cols#80, it#8, lines#25,
- bel=^G, clear=\Ec, cr=^M, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ bel=^G, clear=\Ec, cr=\r, cub=\E[%p1%dD, cub1=^H,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dl=\E[%p1%dM, dl1=\E[M, ed=\E[J, el=\E[K, home=\E[H, ht=^I,
- il=\E[%p1%dL, il1=\E[L, ind=^J, kbs=^H, kcub1=\E[D,
+ il=\E[%p1%dL, il1=\E[L, ind=\n, kbs=^H, kcub1=\E[D,
kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, khome=\E[H, kich1=\E[L,
- kll=\E[F, knp=\E[G, kpp=\E[I, nel=^M^J, rc=\E8, sc=\E7,
+ kll=\E[F, knp=\E[G, kpp=\E[I, nel=\r\n, rc=\E8, sc=\E7,
sgr=\E[0;10%?%p1%t;7%;%?%p3%t;7%;%?%p4%t;5%;%?%p6%t;1%;%?%p7
%t;8%;%?%p9%t;11%;m%?%p5%t\E[=8F%;,
use=klone+sgr8,
vt52|dec vt52,
OTbs,
cols#80, it#8, lines#24,
- acsc=+h.k0affggolpnqprrss, bel=^G, clear=\EH\EJ, cr=^M,
+ acsc=+h.k0affggolpnqprrss, bel=^G, clear=\EH\EJ, cr=\r,
cub1=\ED, cud1=\EB, cuf1=\EC,
cup=\EY%p1%{32}%+%c%p2%{32}%+%c, cuu1=\EA, ed=\EJ,
- el=\EK, home=\EH, ht=^I, ind=^J, kbs=^H, kcub1=\ED, kcud1=\EB,
- kcuf1=\EC, kcuu1=\EA, nel=^M^J, ri=\EI, rmacs=\EG, smacs=\EF,
+ el=\EK, home=\EH, ht=^I, ind=\n, kbs=^H, kcub1=\ED, kcud1=\EB,
+ kcuf1=\EC, kcuu1=\EA, nel=\r\n, ri=\EI, rmacs=\EG, smacs=\EF,
#### DEC VT100 and compatibles
#
cols#80, it#8, lines#24,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m$<2>, bold=\E[1m$<2>,
- clear=\E[H\E[J$<50>, cr=^M, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C$<2>,
+ clear=\E[H\E[J$<50>, cr=\r, cub=\E[%p1%dD, cub1=^H,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C$<2>,
cup=\E[%i%p1%d;%p2%dH$<5>, cuu=\E[%p1%dA,
cuu1=\E[A$<2>, ed=\E[J$<50>, el=\E[K$<3>, el1=\E[1K$<3>,
- enacs=\E(B\E)0, home=\E[H, ht=^I, hts=\EH, ind=^J, kbs=^H,
+ enacs=\E(B\E)0, home=\E[H, ht=^I, hts=\EH, ind=\n, kbs=^H,
kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
rev=\E[7m$<2>, ri=\EM$<5>, rmacs=^O, rmso=\E[m$<2>,
rmul=\E[m$<2>, rs2=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h,
OTbs, am, xenl,
cols#80, it#8, lines#24, vt#3,
bel=^G, blink=\E[5m$<2/>, bold=\E[1m$<2/>,
- clear=\E[;H\E[2J$<50/>, cr=^M, csr=\E[%i%p1%d;%p2%dr,
- cub1=^H, cud1=^J, cuf1=\E[C$<2/>,
+ clear=\E[;H\E[2J$<50/>, cr=\r, csr=\E[%i%p1%d;%p2%dr,
+ cub1=^H, cud1=\n, cuf1=\E[C$<2/>,
cup=\E[%i%p1%d;%p2%dH$<5/>, cuu1=\E[A$<2/>,
ed=\E[J$<50/>, el=\E[K$<3/>, home=\E[H, ht=^I,
is2=\E[1;24r\E[24;1H, kbs=^H, kcub1=\EOD, kcud1=\EOB,
kcuf1=\EOC, kcuu1=\EOA, kf1=\EOP, kf2=\EOQ, kf3=\EOR,
- kf4=\EOS, nel=^M^J, rc=\E8, rev=\E[7m$<2/>, ri=\EM$<5/>,
+ kf4=\EOS, nel=\r\n, rc=\E8, rev=\E[7m$<2/>, ri=\EM$<5/>,
rmam=\E[?7h, rmkx=\E[?1l\E>, rmso=\E[m$<2/>,
rmul=\E[m$<2/>,
rs1=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, sc=\E7,
vt220-old|vt200-old|DEC VT220 in vt100 emulation mode,
OTbs, OTpt, am, mir, msgr, xenl, xon,
cols#80, lines#24, vt#3,
- OTnl=^J,
+ OTnl=\n,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m$<2>, bold=\E[1m$<2>, civis=\E[?25l,
- clear=\E[H\E[2J$<50>, cnorm=\E[?25h, cr=^M,
+ clear=\E[H\E[2J$<50>, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub1=^H, cud1=\E[B, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH$<10>, cuu1=\E[A, dch1=\E[P,
dl1=\E[M, ed=\E[J$<50>, el=\E[K$<3>, home=\E[H, ht=^I,
OTbs, am, mir, msgr, xenl, xon,
cols#80, it#8, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
- bel=^G, blink=\E[5m, bold=\E[1m, clear=\E[H\E[J, cr=^M,
+ bel=^G, blink=\E[5m, bold=\E[1m, clear=\E[H\E[J, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
ech=\E[%p1%dX, ed=\E[J, el=\E[K, el1=\E[1K, enacs=\E)0,
OTbs, am, mc5i, mir, msgr, xenl, xon,
cols#80, it#8, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
- bel=^G, blink=\2335m, bold=\2331m, clear=\233H\233J, cr=^M,
+ bel=^G, blink=\2335m, bold=\2331m, clear=\233H\233J, cr=\r,
csr=\233%i%p1%d;%p2%dr, cub=\233%p1%dD, cub1=^H,
- cud=\233%p1%dB, cud1=^J, cuf=\233%p1%dC, cuf1=\233C,
+ cud=\233%p1%dB, cud1=\n, cuf=\233%p1%dC, cuf1=\233C,
cup=\233%i%p1%d;%p2%dH, cuu=\233%p1%dA, cuu1=\233A,
dch=\233%p1%dP, dch1=\233P, dl=\233%p1%dM, dl1=\233M,
ech=\233%p1%dX, ed=\233J, el=\233K, el1=\2331K, enacs=\E)0,
vt200-js|vt220-js|dec vt200 series with jump scroll,
am, msgr,
cols#80,
- bel=^G, clear=\E[H\E[J, cr=^M, csr=\E[%i%p1%d;%p2%dr,
- cub1=^H, cud1=^J, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
+ bel=^G, clear=\E[H\E[J, cr=\r, csr=\E[%i%p1%d;%p2%dr,
+ cub1=^H, cud1=\n, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu1=\E[A, dch1=\E[P, dl1=\E[M, ed=\E[J, el=\E[K, home=\E[H,
ht=^I, il1=\E[L, ind=\ED,
is2=\E[61"p\E[H\E[?3l\E[?4l\E[?1h\E[?5l\E[?6l\E[?7h\E[?8h\E[
?25h\E>\E[m,
kbs=^H, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
- kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS, nel=^M\ED, rc=\E8,
+ kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS, nel=\r\ED, rc=\E8,
rf=/usr/share/tabset/vt100, ri=\EM, rmdc=, rmir=\E[4l,
rmkx=\E[?1l\E>, rmso=\E[27m$<5/>, rmul=\E[24m,
rs1=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h, sc=\E7, smdc=,
cols#80, lines#24, wsl#80,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, civis=\E[?25l,
- clear=\E[H\E[2J, cnorm=\E[?25h, cr=^M,
+ clear=\E[H\E[2J, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
ech=\E[%p1%dX, ed=\E[J, el=\E[K, el1=\E[1K, home=\E[H, ht=^I,
hts=\EH, ich=\E[%p1%d@, il=\E[%p1%dL, il1=\E[L, ind=\ED,
is2=\E>\E[?3l\E[?4l\E[?5l\E[?7h\E[?8h\E[1;24r\E[24;1H,
- kbs=\177, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
+ kbs=^?, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kdch1=\E[3~, kel=\E[4~, kf10=\E[21~, kf11=\E[23~,
kf12=\E[24~, kf13=\E[25~, kf14=\E[26~, kf15=\E[28~,
kf16=\E[29~, kf17=\E[31~, kf18=\E[32~, kf19=\E[33~,
cols#80, it#8, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
blink=\E[5m, bold=\E[1m, civis=\E[?25l, clear=\E[H\E[J,
- cnorm=\E[?25h, cr=^M, csr=\E[%i%p1%d;%p2%dr,
- cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=^J,
+ cnorm=\E[?25h, cr=\r, csr=\E[%i%p1%d;%p2%dr,
+ cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=\n,
cuf=\E[%p1%dC, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu=\E[%p1%dA, cuu1=\E[A, dch=\E[%p1%dP, dch1=\E[P,
dl=\E[%p1%dM, dl1=\E[M, dsl=\E[2$~\r\E[1$}\E[K\E[$},
kbs=^H, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS, kf6=\E[17~,
kf7=\E[18~, kf8=\E[19~, kf9=\E[20~, lf1=pf1, lf2=pf2,
- lf3=pf3, lf4=pf4, nel=^M\ED, rc=\E8, rev=\E[7m,
+ lf3=pf3, lf4=pf4, nel=\r\ED, rc=\E8, rev=\E[7m,
rf=/usr/share/tabset/vt300, ri=\EM, rmacs=\E(B,
rmam=\E[?7l, rmir=\E[4l, rmkx=\E[?1l\E>, rmso=\E[27m,
rmul=\E[24m, rs1=\E[?3l, sc=\E7,
cols#80, it#8, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
blink=\E[5m, bold=\E[1m, civis=\E[?25l,
- clear=\E[H\E[J$<10/>, cnorm=\E[?25h, cr=^M,
+ clear=\E[H\E[J$<10/>, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
dsl=\E[2$~\r\E[1$}\E[K\E[$}, ed=\E[J$<10/>,
kbs=^H, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS, kf6=\E[17~,
kf7=\E[18~, kf8=\E[19~, kf9=\E[20~, lf1=pf1, lf2=pf2,
- lf3=pf3, lf4=pf4, nel=^M\ED, rc=\E8, rev=\E[7m,
+ lf3=pf3, lf4=pf4, nel=\r\ED, rc=\E8, rev=\E[7m,
rf=/usr/share/tabset/vt300, ri=\EM, rmacs=\E(B,
rmam=\E[?7l, rmir=\E[4l, rmkx=\E[?1l\E>, rmso=\E[27m,
rmul=\E[24m, rs1=\E<\E[?3l\E[!p\E[?7h, sc=\E7,
cols#80, it#8, lines#24, vt#3,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m$<2>, bold=\E[1m$<2>, civis=\E[?25l,
- clear=\E[H\E[2J$<50>, cnorm=\E[?25h, cr=^M,
+ clear=\E[H\E[2J$<50>, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH$<10>, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
ech=\E[%p1%dX, ed=\E[J$<50>, el=\E[K$<3>, el1=\E[1K,
# application has to know it.
#
vt420pc|DEC VT420 w/PC keyboard,
- kdch1=\177, kend=\E[4~, kf1=\E[11~, kf10=\E[21~,
- kf11=\E[23~, kf12=\E[24~, kf13=\E[11;2~, kf14=\E[12;2~,
- kf15=\E[13;2~, kf16=\E[14;2~, kf17=\E[15;2~,
- kf18=\E[17;2~, kf19=\E[18;2~, kf2=\E[12~, kf20=\E[19;2~,
- kf21=\E[20;2~, kf22=\E[21;2~, kf23=\E[23;2~,
- kf24=\E[24;2~, kf25=\E[23~, kf26=\E[24~, kf27=\E[25~,
- kf28=\E[26~, kf29=\E[28~, kf3=\E[13~, kf30=\E[29~,
- kf31=\E[31~, kf32=\E[32~, kf33=\E[33~, kf34=\E[34~,
- kf35=\E[35~, kf36=\E[36~, kf37=\E[23;2~, kf38=\E[24;2~,
- kf39=\E[25;2~, kf4=\E[14~, kf40=\E[26;2~, kf41=\E[28;2~,
- kf42=\E[29;2~, kf43=\E[31;2~, kf44=\E[32;2~,
- kf45=\E[33;2~, kf46=\E[34;2~, kf47=\E[35;2~,
- kf48=\E[36;2~, kf5=\E[15~, kf6=\E[17~, kf7=\E[18~,
- kf8=\E[19~, kf9=\E[20~, khome=\E[H,
+ kdch1=^?, kend=\E[4~, kf1=\E[11~, kf10=\E[21~, kf11=\E[23~,
+ kf12=\E[24~, kf13=\E[11;2~, kf14=\E[12;2~, kf15=\E[13;2~,
+ kf16=\E[14;2~, kf17=\E[15;2~, kf18=\E[17;2~,
+ kf19=\E[18;2~, kf2=\E[12~, kf20=\E[19;2~, kf21=\E[20;2~,
+ kf22=\E[21;2~, kf23=\E[23;2~, kf24=\E[24;2~, kf25=\E[23~,
+ kf26=\E[24~, kf27=\E[25~, kf28=\E[26~, kf29=\E[28~,
+ kf3=\E[13~, kf30=\E[29~, kf31=\E[31~, kf32=\E[32~,
+ kf33=\E[33~, kf34=\E[34~, kf35=\E[35~, kf36=\E[36~,
+ kf37=\E[23;2~, kf38=\E[24;2~, kf39=\E[25;2~, kf4=\E[14~,
+ kf40=\E[26;2~, kf41=\E[28;2~, kf42=\E[29;2~,
+ kf43=\E[31;2~, kf44=\E[32;2~, kf45=\E[33;2~,
+ kf46=\E[34;2~, kf47=\E[35;2~, kf48=\E[36;2~, kf5=\E[15~,
+ kf6=\E[17~, kf7=\E[18~, kf8=\E[19~, kf9=\E[20~, khome=\E[H,
pctrm=USR_TERM\:vt420pcdos\:,
pfx=\EP1;1|%?%{16}%p1%>%t%{0}%e%{21}%p1%>%t%{1}%e%{25}%p1%>
%t%{2}%e%{27}%p1%>%t%{3}%e%{30}%p1%>%t%{4}%e%{5}%;%p1%+
sgr0=\E[m, smsc=\E[?1;2r\E[34h, use=vt420pc,
vt420f|DEC VT420 with VT kbd; VT400 mode; F1-F5 used as Fkeys,
- kdch1=\177, kf1=\E[11~, kf10=\E[21~, kf11=\E[23~,
+ kdch1=^?, kf1=\E[11~, kf10=\E[21~, kf11=\E[23~,
kf12=\E[24~, kf13=\E[25~, kf14=\E[26~, kf15=\E[28~,
kf16=\E[29~, kf17=\E[31~, kf18=\E[32~, kf19=\E[33~,
kf2=\E[12~, kf20=\E[34~, kf3=\E[13~, kf4=\E[14~,
colors#8, it#8, ncv#22, pairs#64, U8#1,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z, civis=\E[?25l,
- clear=\E[H\E[J, cnorm=\E[?25h, cr=^M,
+ clear=\E[H\E[J, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
cud=\E[%p1%dB, cud1=\ED, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\EM,
dl=\E[%p1%dM, dl1=\E[M, ech=\E[%p1%dX, ed=\E[J, el=\E[K,
el1=\E[1K, enacs=\E(B\E)0, flash=\E[?5h$<100/>\E[?5l,
home=\E[H, hpa=\E[%i%p1%dG, ht=^I, hts=\EH, il=\E[%p1%dL,
- il1=\E[L, ind=^J, indn=\E[%p1%dS,
+ il1=\E[L, ind=\n, indn=\E[%p1%dS,
initc=\E]P%p1%x%p2%{255}%*%{1000}%/%02x%p3%{255}%*%{1000}%/
%02x%p4%{255}%*%{1000}%/%02x,
is2=\E7\E[r\E[m\E[?7h\E[?1;4;6l\E[4l\E8\E>\E]R,
- kLFT=\E[D, kRIT=\E[C, kb2=\E[G, kbs=\177, kcbt=\E[Z,
+ kLFT=\E[D, kRIT=\E[C, kb2=\E[G, kbs=^?, kcbt=\E[Z,
kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kdch1=\E[3~, kend=\E[4~, khome=\E[1~, kich1=\E[2~,
kind=\E[B, kmous=\E[M, knp=\E[6~, kpp=\E[5~, kri=\E[A,
- kspd=^Z, nel=^M^J, oc=\E]R, op=\E[39;49m, rc=\E8, rev=\E[7m,
+ kspd=^Z, nel=\r\n, oc=\E]R, op=\E[39;49m, rc=\E8, rev=\E[7m,
ri=\EM, rin=\E[%p1%dT, rmacs=^O, rmam=\E[?7l,
rmcup=\E[2J\E[?47l, rmir=\E[4l, rmkx=\E[?1l\E>,
rmpch=\E[10m, rmso=\E[27m, rmul=\E[24m,
#
putty+fnkeys+sco|SCO fn-keys for PuTTY,
kbeg=\E[E, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
- kdch1=\177, kend=\E[F, kf1=\E[M, kf10=\E[V, kf11=\E[W,
+ kdch1=^?, kend=\E[F, kf1=\E[M, kf10=\E[V, kf11=\E[W,
kf12=\E[X, kf13=\E[Y, kf14=\E[Z, kf15=\E[a, kf16=\E[b,
kf17=\E[c, kf18=\E[d, kf19=\E[e, kf2=\E[N, kf20=\E[f,
kf21=\E[g, kf22=\E[h, kf23=\E[i, kf24=\E[j, kf25=\E[k,
#
# The missing "=" in smkx is not a typo (here), but an error in tkterm.
tt|tkterm|Don Libes' tk text widget terminal emulator,
- clear=\E[H\E[J, cr=^M, cub1=^H, cud1=^J, cuf1=\E[C,
- cup=\E[%p1%d;%p2%dH, cuu1=\E[A, ind=^J, kf1=\EOP, kf2=\EOQ,
+ clear=\E[H\E[J, cr=\r, cub1=^H, cud1=\n, cuf1=\E[C,
+ cup=\E[%p1%d;%p2%dH, cuu1=\E[A, ind=\n, kf1=\EOP, kf2=\EOQ,
kf3=\EOR, kf4=\EOS, kf5=\EOT, kf6=\EOU, kf7=\EOV, kf8=\EOW,
kf9=\EOX, rmkx=\E[?1l\E>, rmso=\E[m, smkx=\E[?1h\E,
smso=\E[7m,
OTbs, am, km, mir, msgr, xenl, xon,
cols#80, it#8, lines#65,
bold=\E[1m, clear=\E[H\E[2J, csr=\E[%i%p1%d;%p2%dr,
- cub1=^H, cud1=^J, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
+ cub1=^H, cud1=\n, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu1=\E[A, dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM,
dl1=\E[M, ed=\E[J, el=\E[K, home=\E[H, ht=^I, il=\E[%p1%dL,
- il1=\E[L, ind=^J, is2=\E\E[m\E[?7h\E[?1;4l, kbs=^H,
+ il1=\E[L, ind=\n, is2=\E\E[m\E[?7h\E[?1;4l, kbs=^H,
kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA, kf1=\EOP,
kf2=\EOQ, kf3=\EOR, kf4=\EOS, rev=\E[7m, ri=\EM, rmam=\E[?7l,
rmir=\E[4l, rmkx=\E[?1l\E>, rmso=\E[m, rmul=\E[m,
xterm-r5|xterm R5 version,
OTbs, am, km, msgr, xenl,
cols#80, it#8, lines#24,
- bel=^G, bold=\E[1m, clear=\E[H\E[2J, cr=^M,
+ bel=^G, bold=\E[1m, clear=\E[H\E[2J, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J,
el=\E[K, home=\E[H, ht=^I, hts=\EH, ich=\E[%p1%d@, ich1=\E[@,
- il=\E[%p1%dL, il1=\E[L, ind=^J, kbs=^H, kcub1=\EOD,
+ il=\E[%p1%dL, il1=\E[L, ind=\n, kbs=^H, kcub1=\EOD,
kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA, kdch1=\E[3~,
kdl1=\E[31~, kel=\E[8~, kend=\E[4~, kf0=\EOq, kf1=\E[11~,
kf10=\E[21~, kf11=\E[23~, kf12=\E[24~, kf2=\E[12~,
OTbs, am, km, mir, msgr, xenl,
cols#80, it#8, lines#24,
acsc=``aaffggiijjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
- bel=^G, bold=\E[1m, clear=\E[H\E[2J, cr=^M,
+ bel=^G, bold=\E[1m, clear=\E[H\E[2J, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J,
el=\E[K, enacs=\E)0, home=\E[H, ht=^I, hts=\EH, il=\E[%p1%dL,
- il1=\E[L, ind=^J,
+ il1=\E[L, ind=\n,
is2=\E[m\E[?7h\E[4l\E>\E7\E[r\E[?1;3;4;6l\E8, kbs=^H,
kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kdch1=\E[3~, kf1=\E[11~, kf10=\E[21~, kf11=\E[23~,
cols#80, it#8, lines#24, ncv@,
acsc=``aaffggiijjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, bold=\E[1m, cbt=\E[Z, civis=\E[?25l,
- clear=\E[H\E[2J, cnorm=\E[?25h, cr=^M,
+ clear=\E[H\E[2J, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
ech=\E[%p1%dX, ed=\E[J, el=\E[K, el1=\E[1K, enacs=\E(B\E)0,
flash=\E[?5h$<100/>\E[?5l, home=\E[H, hpa=\E[%i%p1%dG,
ht=^I, hts=\EH, ich=\E[%p1%d@, ich1=\E[@, il=\E[%p1%dL,
- il1=\E[L, ind=^J,
+ il1=\E[L, ind=\n,
is2=\E7\E[r\E[m\E[?7h\E[?1;3;4;6l\E[4l\E8\E>,
kbeg=\EOE, kbs=^H, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC,
- kcuu1=\EOA, kdch1=\177, kend=\EOF, kf1=\E[11~, kf10=\E[21~,
+ kcuu1=\EOA, kdch1=^?, kend=\EOF, kf1=\E[11~, kf10=\E[21~,
kf11=\E[23~, kf12=\E[24~, kf13=\E[25~, kf14=\E[26~,
kf15=\E[28~, kf16=\E[29~, kf17=\E[31~, kf18=\E[32~,
kf19=\E[33~, kf2=\E[12~, kf20=\E[34~, kf3=\E[13~,
colors#8, cols#80, it#8, lines#24, pairs#64,
acsc=``aaffggiijjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z, civis=\E[?25l,
- clear=\E[H\E[2J, cnorm=\E[?12l\E[?25h, cr=^M,
+ clear=\E[H\E[2J, cnorm=\E[?12l\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
cvvis=\E[?12;25h, dch=\E[%p1%dP, dch1=\E[P, dim=\E[2m,
dl=\E[%p1%dM, dl1=\E[M, ech=\E[%p1%dX, ed=\E[J, el=\E[K,
el1=\E[1K, flash=\E[?5h$<100/>\E[?5l, home=\E[H,
hpa=\E[%i%p1%dG, ht=^I, hts=\EH, ich=\E[%p1%d@,
- il=\E[%p1%dL, il1=\E[L, ind=^J, invis=\E[8m,
+ il=\E[%p1%dL, il1=\E[L, ind=\n, invis=\E[8m,
is2=\E[!p\E[?3;4l\E[4l\E>, kmous=\E[M, meml=\El,
memu=\Em, op=\E[39;49m, rc=\E8, rev=\E[7m, ri=\EM,
ritm=\E[23m, rmacs=\E(B, rmam=\E[?7l, rmcup=\E[?1049l,
acsc=``aaffggiijjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\2335m, bold=\2331m, cbt=\233Z,
civis=\233?25l, clear=\233H\2332J,
- cnorm=\233?25l\233?25h, cr=^M, csr=\233%i%p1%d;%p2%dr,
- cub=\233%p1%dD, cub1=^H, cud=\233%p1%dB, cud1=^J,
+ cnorm=\233?25l\233?25h, cr=\r, csr=\233%i%p1%d;%p2%dr,
+ cub=\233%p1%dD, cub1=^H, cud=\233%p1%dB, cud1=\n,
cuf=\233%p1%dC, cuf1=\233C, cup=\233%i%p1%d;%p2%dH,
cuu=\233%p1%dA, cuu1=\233A, cvvis=\233?12;25h,
dch=\233%p1%dP, dch1=\233P, dl=\233%p1%dM, dl1=\233M,
ech=\233%p1%dX, ed=\233J, el=\233K, el1=\2331K,
flash=\233?5h$<100/>\233?5l, home=\233H,
hpa=\233%i%p1%dG, ht=^I, hts=\210, ich=\233%p1%d@,
- il=\233%p1%dL, il1=\233L, ind=^J, invis=\2338m,
+ il=\233%p1%dL, il1=\233L, ind=\n, invis=\2338m,
is2=\E[62"p\E\sG\233m\233?7h\E>\E7\233?1;3;4;6l\2334l\233r
\E8,
ka1=\217w, ka3=\217u, kb2=\217y, kbeg=\217E, kc1=\217q,
xterm-sco|xterm with SCO function keys,
kbeg=\E[E, kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
- kdch1=\177, kend=\E[F, kf1=\E[M, kf10=\E[V, kf11=\E[W,
+ kdch1=^?, kend=\E[F, kf1=\E[M, kf10=\E[V, kf11=\E[W,
kf12=\E[X, kf13=\E[Y, kf14=\E[Z, kf15=\E[a, kf16=\E[b,
kf17=\E[c, kf18=\E[d, kf19=\E[e, kf2=\E[N, kf20=\E[f,
kf21=\E[g, kf22=\E[h, kf23=\E[i, kf24=\E[j, kf25=\E[k,
xterm-vt52|xterm emulating dec vt52,
cols#80, it#8, lines#24,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
- bel=^G, clear=\EH\EJ, cr=^M, cub1=\ED, cud1=\EB, cuf1=\EC,
+ bel=^G, clear=\EH\EJ, cr=\r, cub1=\ED, cud1=\EB, cuf1=\EC,
cup=\EY%p1%' '%+%c%p2%' '%+%c, cuu1=\EA, ed=\EJ, el=\EK,
- home=\EH, ht=^I, ind=^J, kcub1=\ED, kcud1=\EB, kcuf1=\EC,
- kcuu1=\EA, nel=^M^J, ri=\EI, rmacs=\EG, smacs=\EF,
+ home=\EH, ht=^I, ind=\n, kcub1=\ED, kcud1=\EB, kcuf1=\EC,
+ kcuu1=\EA, nel=\r\n, ri=\EI, rmacs=\EG, smacs=\EF,
use=xterm+kbs,
xterm-noapp|xterm with cursor keys in normal mode,
OTbs, am, km, mir, msgr, xenl,
btns#3, cols#80, it#8, lines#24,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
- bel=^G, blink@, bold=\E[1m, clear=\E[H\E[2J, cr=^M,
+ bel=^G, blink@, bold=\E[1m, clear=\E[H\E[2J, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=\E[D,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J,
el=\E[K, el1=\E[1K$<3>, enacs=\E(B\E)0, getm=\E[%p1%dY,
home=\E[H, ht=^I, hts=\EH, ich=\E[%p1%d@, ich1=\E[@,
- il=\E[%p1%dL, il1=\E[L, ind=^J, kbs=^H, kcub1=\EOD,
+ il=\E[%p1%dL, il1=\E[L, ind=\n, kbs=^H, kcub1=\EOD,
kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA, kend=\E[Y, kf0=\EOy,
kf10=\EOY, kf11=\EOZ, kf12=\EOA, kf5=\EOT, kf6=\EOU,
kf7=\EOV, kf8=\EOW, kf9=\EOX, khome=\E[H, kmous=\E[^_,
OTbs, am, km, mir, msgr, xenl, XT,
cols#80, it#8, lines#65, ncv@,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
- bel=^G, bold=\E[1m, clear=\E[H\E[2J, cr=^M,
+ bel=^G, bold=\E[1m, clear=\E[H\E[2J, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J,
el=\E[K, el1=\E[1K, enacs=\E(B\E)0, home=\E[H, ht=^I,
- ich=\E[%p1%d@, il=\E[%p1%dL, il1=\E[L, ind=^J,
+ ich=\E[%p1%d@, il=\E[%p1%dL, il1=\E[L, ind=\n,
is1=\E[r\E[m\E[?7h\E[?4;6l\E[4l, kbs=^H, kcub1=\EOD,
kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA, kend=\E[8~, kf1=\E[11~,
kf10=\E[21~, kf11=\E[23~, kf12=\E[24~, kf2=\E[12~,
# this describes the alpha-version of Gnome terminal shipped with Redhat 6.0
gnome-rh62|Gnome terminal,
bce,
- kdch1=\177, kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS,
+ kdch1=^?, kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS,
use=xterm-color,
# GNOME Terminal 1.4.0.4 (Redhat 7.2)
# that it implements kcbt.
gnome-rh80|GNOME Terminal,
bce@, msgr@,
- ech=\E[%p1%dX, flash=\E[?5h$<100/>\E[?5l, kbs=\177,
+ ech=\E[%p1%dX, flash=\E[?5h$<100/>\E[?5l, kbs=^?,
kcbt=\E^I, op=\E[39;49m, use=gnome-rh72,
# GNOME Terminal 2.2.1 (Redhat 9.0)
# or not is debatable).
kvt|KDE terminal,
bce, km@,
- kdch1=\177, kend=\E[F, khome=\E[H, use=xterm-color,
+ kdch1=^?, kend=\E[F, khome=\E[H, use=xterm-color,
# Konsole 1.0.1
# (formerly known as kvt)
ncv@,
bel@, blink=\E[5m, civis=\E[?25l, cnorm=\E[?25h,
ech=\E[%p1%dX, flash=\E[?5h$<100/>\E[?5l,
- hpa=\E[%i%p1%dG, indn=\E[%p1%dS, kbs=\177, kdch1=\E[3~,
+ hpa=\E[%i%p1%dG, indn=\E[%p1%dS, kbs=^?, kdch1=\E[3~,
kend=\E[4~, kf1@, kf10@, kf11@, kf12@, kf13@, kf14@, kf15@, kf16@,
kf17@, kf18@, kf19@, kf2@, kf20@, kf3@, kf4@, kf5@, kf6@, kf7@, kf8@,
kf9@, kfnd@, khome=\E[1~, kslt@, rin=\E[%p1%dT, ritm=\E[23m,
# KDE's "vt100" keyboard has no relationship to any terminal that DEC made, but
# it is still useful for deriving the other entries.
konsole-vt100|KDE console window with vt100 (sic) keyboard,
- kbs=\177, kdch1=\E[3~, kend=\E[F, kf1=\E[11~, kf10=\E[21~,
+ kbs=^?, kdch1=\E[3~, kend=\E[F, kf1=\E[11~, kf10=\E[21~,
kf11=\E[23~, kf12=\E[24~, kf13@, kf14@, kf15@, kf16@, kf17@,
kf18@, kf19@, kf2=\E[12~, kf20@, kf3=\E[13~, kf4=\E[14~,
kf5=\E[15~, kf6=\E[17~, kf7=\E[18~, kf8=\E[19~, kf9=\E[20~,
khome=\E[H, use=konsole-base,
konsole-vt420pc|KDE console window with vt420 pc keyboard,
- kbs=^H, kdch1=\177, use=konsole-vt100,
+ kbs=^H, kdch1=^?, use=konsole-vt100,
konsole-16color|klone of xterm-16color,
ncv#32, use=ibm+16color, use=konsole,
# make a default entry for konsole
colors#8, cols#80, it#8, lines#24, pairs#64,
acsc=00``aaffgghhjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, bold=\E[1m, cbt=\E[Z, civis=\E[?25l,
- clear=\E[H\E[2J, cnorm=\E[?25h, cr=^M,
+ clear=\E[H\E[2J, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
ech=\E[%p1%dX, ed=\E[J, el=\E[K, el1=\E[1K, enacs=,
home=\E[H, hpa=\E[%i%p1%dG, ht=^I, hts=\EH, ich=\E[%p1%d@,
- ich1=\E[@, il=\E[%p1%dL, il1=\E[L, ind=^J, indn=\E[%p1%dS,
- is2=\E7\E[r\E[m\E[?7h\E[?1;3;4;6l\E[4l\E8\E>,
- kbs=\177, kcbt=\E[Z, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC,
- kcuu1=\EOA, kdch1=\E[3~, kend=\EOF, kent=\EOM, kfnd=\E[1~,
- khome=\EOH, kich1=\E[2~, kind=\EO1;2B, kmous=\E[M,
- knp=\E[6~, kpp=\E[5~, kri=\EO1;2A, kslt=\E[4~, mc0=\E[i,
- nel=\EE, op=\E[39;49m, rc=\E8, rev=\E[7m, ri=\EM,
- rin=\E[%p1%dT, rmacs=\E(B, rmam=\E[?7l, rmcup=\E[?1049l,
- rmir=\E[4l, rmkx=\E[?1l\E>, rmso=\E[27m, rmul=\E[24m,
+ ich1=\E[@, il=\E[%p1%dL, il1=\E[L, ind=\n, indn=\E[%p1%dS,
+ is2=\E7\E[r\E[m\E[?7h\E[?1;3;4;6l\E[4l\E8\E>, kbs=^?,
+ kcbt=\E[Z, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
+ kdch1=\E[3~, kend=\EOF, kent=\EOM, kfnd=\E[1~, khome=\EOH,
+ kich1=\E[2~, kind=\EO1;2B, kmous=\E[M, knp=\E[6~,
+ kpp=\E[5~, kri=\EO1;2A, kslt=\E[4~, mc0=\E[i, nel=\EE,
+ op=\E[39;49m, rc=\E8, rev=\E[7m, ri=\EM, rin=\E[%p1%dT,
+ rmacs=\E(B, rmam=\E[?7l, rmcup=\E[?1049l, rmir=\E[4l,
+ rmkx=\E[?1l\E>, rmso=\E[27m, rmul=\E[24m,
rs2=\E7\E[r\E8\E[m\E[?7h\E[?1;3;4;6l\E[4l\E>\E[?1000l,
sc=\E7, setab=\E[4%p1%dm, setaf=\E[3%p1%dm,
sgr=\E[0%?%p6%t;1%;%?%p2%t;4%;%?%p1%p3%|%t;7%;m%?%p9%t\E(0%e
cols#80, it#8, lines#24,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, civis=\E[?25l,
- clear=\E[H\E[2J, cnorm=\E[?25h, cr=^M,
+ clear=\E[H\E[2J, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dl=\E[%p1%dM, dl1=\E[M, ed=\E[J, el=\E[K, el1=\E[1K,
enacs=\E(B\E)0, flash=\E[?5h$<100/>\E[?5l, home=\E[H,
ht=^I, hts=\EH, ich=\E[%p1%d@, ich1=\E[@, il=\E[%p1%dL,
- il1=\E[L, ind=^J, is1=\E[?47l\E=\E[?1l,
+ il1=\E[L, ind=\n, is1=\E[?47l\E=\E[?1l,
is2=\E[r\E[m\E[2J\E[H\E[?7h\E[?1;3;4;6l\E[4l, kbs=^H,
kcbt=\E[Z, kmous=\E[M, rc=\E8, rev=\E[7m, ri=\EM, rmacs=^O,
rmcup=\E[2J\E[?47l\E8, rmir=\E[4l, rmkx=\E>, rmso=\E[27m,
btns#5, cols#80, it#8, lines#24, lm#0, ncv@,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, civis=\E[?25l,
- clear=\E[H\E[2J, cnorm=\E[?25h, cr=^M,
+ clear=\E[H\E[2J, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
cud=\E[%p1%dB, cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
ech=\E[%p1%dX, ed=\E[J, el=\E[K, el1=\E[1K, enacs=\E)0,
home=\E[H, hpa=\E[%i%p1%dG, ht=^I, hts=\EH, ich=\E[%p1%d@,
- ich1=\E[@, il=\E[%p1%dL, il1=\E[L, ind=^J,
+ ich1=\E[@, il=\E[%p1%dL, il1=\E[L, ind=\n,
is1=\E[?47l\E>\E[?1l,
is2=\E[r\E[m\E[2J\E[H\E[?7h\E[?1;3;4;6l\E[4l, kNXT@,
kPRV@, ka1=\E[7~, ka3=\E[5~, kb2=\EOu, kbeg=\EOu, kbs=^H,
# Based on rxvt 2.4.8, it has a few differences in key bindings
aterm|AfterStep terminal,
XT,
- kbs=\177, kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS, use=rxvt,
+ kbs=^?, kf1=\EOP, kf2=\EOQ, kf3=\EOR, kf4=\EOS, use=rxvt,
#### XITERM
# xiterm 0.5-5.2
# see also http://invisible-island.net/xterm/xterm.faq.html#bug_xiterm
xiterm|internationalized terminal emulator for X,
km@,
- kbs=\177, kdch1=\E[3~, use=klone+color, use=xterm-r6,
+ kbs=^?, kdch1=\E[3~, use=klone+color, use=xterm-r6,
#### HPTERM
hpterm|X-hpterm|hp X11 terminal emulator,
am, da, db, mir, xhp,
cols#80, lh#2, lines#24, lm#0, lw#8, nlab#8, pb#9600, xmc#0,
- acsc=, bel=^G, bold=\E&dB, cbt=\Ei, clear=\E&a0y0C\EJ, cr=^M,
+ acsc=, bel=^G, bold=\E&dB, cbt=\Ei, clear=\E&a0y0C\EJ, cr=\r,
cub1=^H, cud1=\EB, cuf1=\EC, cup=\E&a%p1%dy%p2%dC,
cuu1=\EA, dch1=\EP, dim=\E&dH, dl1=\EM, ed=\EJ$<1>, el=\EK,
- hpa=\E&a%p1%dC, ht=^I, hts=\E1, il1=\EL, ind=^J, kbs=^H,
+ hpa=\E&a%p1%dC, ht=^I, hts=\E1, il1=\EL, ind=\n, kbs=^H,
kclr=\EJ, kctab=\E2, kcub1=\ED, kcud1=\EB, kcuf1=\EC,
kcuu1=\EA, kdch1=\EP, kdl1=\EM, ked=\EJ, kel=\EK, kf1=\Ep,
kf2=\Eq, kf3=\Er, kf4=\Es, kf5=\Et, kf6=\Eu, kf7=\Ev, kf8=\Ew,
acsc=61a\202f\260g2j\213k\214l\215m\216n\217o\220q\222s
\224t\225u\226v\227w\230x\231~\244,
bel=^G, blink=\EW, bold=\EU, civis=\EZ, clear=\EP\EE0;0;,
- cnorm=\Ea, cr=^M, csr=\Ek%p1%d;%p2%d;, cub=\Eq-%p1%d;,
+ cnorm=\Ea, cr=\r, csr=\Ek%p1%d;%p2%d;, cub=\Eq-%p1%d;,
cub1=^H, cud=\Ep%p1%d;, cud1=\EB, cuf=\Eq%p1%d;, cuf1=\EC,
cup=\EE%p1%d;%p2%d;, cuu=\Ep-%p1%d;, cuu1=\EA,
dch=\EI%p1%d;, dch1=\EI1;, dl=\ER%p1%d;, dl1=\ER1;,
ech=\Ej%p1%d;, ed=\EN, el=\EK, el1=\EL, home=\EE0;0;, ht=^I,
hts=\Eh, il=\EQ%p1%d;, il1=\EQ1;, ind=\EG,
is2=\ES\Er0;\Es0;, kbs=^H, kcub1=\EC, kcud1=\EB, kcuf1=\ED,
- kcuu1=\EA, kdch1=\177, kent=^M, kf0=\EF00, kf1=\EF01,
+ kcuu1=\EA, kdch1=^?, kent=\r, kf0=\EF00, kf1=\EF01,
kf10=\EF10, kf11=\EF11, kf12=\EF12, kf13=\EF13, kf14=\EF14,
kf15=\EF15, kf16=\EF16, kf17=\EF17, kf18=\EF18, kf19=\EF19,
kf2=\EF02, kf20=\EF20, kf3=\EF03, kf4=\EF04, kf5=\EF05,
cols#80, it#8, lines#24, vt#200,
acsc=aaffggjjkkllmmnnooqqssttuuvvwwxx~~, bel=^G,
blink=\E[0;5m, bold=\E[0;1m, civis=\E[?25l,
- clear=\E[2J\E[H, cnorm=\E[?25h, cr=^M,
+ clear=\E[2J\E[H, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=\E[1D,
cud=\E[%p1%dB, cud1=\E[1B, cuf=\E[%p1%dC, cuf1=\E[1C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[1A,
am, eslok, hs, km, mir, msgr, xenl,
colors#8, cols#80, it#8, lines#24, pairs#64,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
- bel=^G, blink=\E[5m, bold=\E[1m, clear=\E[H\E[2J, cr=^M,
+ bel=^G, blink=\E[5m, bold=\E[1m, clear=\E[H\E[2J, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M,
dsl=\E[?E, ed=\E[J, el=\E[K, el1=\E[1K$<3>, enacs=\E(B\E)0,
fsl=\E[?F, home=\E[H, ht=^I, hts=\EH, ich=\E[%p1%d@,
- ich1=\E[@, il=\E[%p1%dL, il1=\E[L, ind=^J, kbs=^H,
+ ich1=\E[@, il=\E[%p1%dL, il1=\E[L, ind=\n, kbs=^H,
kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA, kf0=\EOy,
kf10=\EOx, kf5=\EOt, kf6=\EOu, kf7=\EOv, kf8=\EOl, kf9=\EOw,
op=\E[100m, rc=\E8, rev=\E[7m, ri=\EM, rmacs=^O,
am, bw, mir, msgr,
it#8,
acsc=``aaffggiijjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
- bel=^G, blink=\E[5m, bold=\E[1m, clear=\E[H\E[J, cr=^M,
+ bel=^G, blink=\E[5m, bold=\E[1m, clear=\E[H\E[J, cr=\r,
cub=\E[%p1%dD, cub1=\E[D, cud=\E[%p1%dB, cud1=\E[B,
cuf=\E[%p1%dC, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu=\E[%p1%dA, cuu1=\E[A, dch=\E[%p1%dP, dch1=\E[P,
mterm|mouse-sun|Der Mouse term,
am, bw, mir,
it#8,
- bel=^G, clear=^L, cr=^M, cub1=^H, cud1=^N, cuf1=^S,
+ bel=^G, clear=^L, cr=\r, cub1=^H, cud1=^N, cuf1=^S,
cup=\006%p1%d.%p2%d., cuu1=^X, dch1=^Y, dl1=^K, ed=^B, el=^C,
- home=^P, ht=^I, il1=^A, ind=^U, kbs=^H, ll=^R, nel=^M^U, ri=^W,
+ home=^P, ht=^I, il1=^A, ind=^U, kbs=^H, ll=^R, nel=\r^U, ri=^W,
rmir=^O, rmso=^T, smir=^Q, smso=^V,
# "mterm -type decansi" sets $TERM to "decansi"
#
colors#8, it#8, pairs#64,
acsc=``aaffggiijjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, civis=\E[?25l,
- clear=\E[H\E[J, cnorm=\E[?25h, cr=^M,
+ clear=\E[H\E[J, cnorm=\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=\E[D,
cud=\E[%p1%dB, cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
colors#8, pairs#64,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, civis=\E[?25l,
- clear=\E[H\E[J, cnorm=\E[?25h, cr=^M, cub=\E[%p1%dD,
+ clear=\E[H\E[J, cnorm=\E[?25h, cr=\r, cub=\E[%p1%dD,
cub1=^H, cud=\E[%p1%dB, cud1=\E[B, cuf=\E[%p1%dC,
cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA,
cuu1=\E[A, cvvis=\E[?25h, dim=\E[2m, ed=\E[J, el=\E[K,
- home=\E[H, il1=\E[L, ind=^J, invis=\E[8m, kcub1=\E[D,
+ home=\E[H, il1=\E[L, ind=\n, invis=\E[8m, kcub1=\E[D,
kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A, kdch1=\E[3~,
kend=\E[4~, kf1=\E[[A, kf10=\E[21~, kf11=\E[22~,
kf12=\E[23~, kf2=\E[[B, kf3=\E[[C, kf4=\E[[D, kf5=\E[[E,
mgr|Bellcore MGR (non X) window system terminal emulation,
am, km,
- bel=^G, bold=\E2n, civis=\E9h, clear=^L, cnorm=\Eh, cr=^M,
+ bel=^G, bold=\E2n, civis=\E9h, clear=^L, cnorm=\Eh, cr=\r,
csr=\E%p1%d;%p2%dt, cub1=^H, cud1=\Ef, cuf1=\Er,
cup=\E%p2%d;%p1%dM, cuu1=\Eu, cvvis=\E0h,
dch=\E%p1%dE$<5>, dch1=\EE, dl=\E%p1%dd$<3*>,
dl1=\Ed$<3>, ed=\EC, el=\Ec, hd=\E1;2f, ht=^I, hu=\E1;2u,
ich=\E%p1%dA$<5>, ich1=\EA, il=\E%p1%da$<3*>,
- il1=\Ea$<3>, ind=^J, kbs=^H, kcub1=\E[D, kcud1=\E[B,
- kcuf1=\E[C, kcuu1=\E[A, nel=^M^J, rev=\E1n, rmam=\E5S,
+ il1=\Ea$<3>, ind=\n, kbs=^H, kcub1=\E[D, kcud1=\E[B,
+ kcuf1=\E[C, kcuu1=\E[A, nel=\r\n, rev=\E1n, rmam=\E5S,
rmso=\E0n, rmul=\E0n, sgr0=\E0n, smam=\E5s, smso=\E1n,
smul=\E4n,
mgr-sun|Mgr window with Sun keyboard,
acsc=+C\,D-A.B0E``aaffgghFiGjjkkllmmnnooppqqrrssttuuvvwwxxyy
zz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z, civis=\E[?25l,
- clear=\E[H\E[2J, cnorm=\E[?12l\E[?25h, cr=^M,
+ clear=\E[H\E[2J, cnorm=\E[?12l\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
cvvis=\E[?25h, dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM,
dl1=\E[M, ech=\E[%p1%dX, ed=\E[J, el=\E[K, el1=\E[1K,
enacs=\E)0, flash=\E[?5h$<100/>\E[?5l, fsl=^G, home=\E[H,
hpa=\E[%i%p1%dG, ht=^I, hts=\EH, ich=\E[%p1%d@,
- il=\E[%p1%dL, il1=\E[L, ind=^J, indn=\E[%p1%dS,
+ il=\E[%p1%dL, il1=\E[L, ind=\n, indn=\E[%p1%dS,
invis=\E[8m, is2=\E[4l\E>\E[?1034l, kDC=\E[3;2~,
kEND=\E[1;2F, kHOM=\E[1;2H, kIC=\E[2;2~, kLFT=\E[1;2D,
kNXT=\E[6;2~, kPRV=\E[5;2~, kRIT=\E[1;2C, ka1=\E[1~,
- ka3=\E[5~, kb2=\EOu, kbs=\177, kc1=\E[4~, kc3=\E[6~,
- kcbt=\E[Z, kclr=\E[3;5~, kcub1=\EOD, kcud1=\EOB,
- kcuf1=\EOC, kcuu1=\EOA, kdch1=\E[3~, kdl1=\E[3;2~,
- ked=\E[1;5F, kel=\E[1;2F, kend=\E[4~, kent=\EOM, kf1=\EOP,
- kf10=\E[21~, kf11=\E[23~, kf12=\E[24~, kf13=\E[1;2P,
- kf14=\E[1;2Q, kf15=\E[1;2R, kf16=\E[1;2S, kf17=\E[15;2~,
- kf18=\E[17;2~, kf19=\E[18;2~, kf2=\EOQ, kf20=\E[19;2~,
- kf21=\E[20;2~, kf22=\E[21;2~, kf23=\E[23;2~,
- kf24=\E[24;2~, kf25=\E[1;5P, kf26=\E[1;5Q, kf27=\E[1;5R,
- kf28=\E[1;5S, kf29=\E[15;5~, kf3=\EOR, kf30=\E[17;5~,
- kf31=\E[18;5~, kf32=\E[19;5~, kf33=\E[20;5~,
- kf34=\E[21;5~, kf35=\E[23;5~, kf36=\E[24;5~,
- kf37=\E[1;6P, kf38=\E[1;6Q, kf39=\E[1;6R, kf4=\EOS,
- kf40=\E[1;6S, kf41=\E[15;6~, kf42=\E[17;6~,
- kf43=\E[18;6~, kf44=\E[19;6~, kf45=\E[20;6~,
- kf46=\E[21;6~, kf47=\E[23;6~, kf48=\E[24;6~,
- kf49=\E[1;3P, kf5=\E[15~, kf50=\E[1;3Q, kf51=\E[1;3R,
- kf52=\E[1;3S, kf53=\E[15;3~, kf54=\E[17;3~,
+ ka3=\E[5~, kb2=\EOu, kbs=^?, kc1=\E[4~, kc3=\E[6~, kcbt=\E[Z,
+ kclr=\E[3;5~, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC,
+ kcuu1=\EOA, kdch1=\E[3~, kdl1=\E[3;2~, ked=\E[1;5F,
+ kel=\E[1;2F, kend=\E[4~, kent=\EOM, kf1=\EOP, kf10=\E[21~,
+ kf11=\E[23~, kf12=\E[24~, kf13=\E[1;2P, kf14=\E[1;2Q,
+ kf15=\E[1;2R, kf16=\E[1;2S, kf17=\E[15;2~, kf18=\E[17;2~,
+ kf19=\E[18;2~, kf2=\EOQ, kf20=\E[19;2~, kf21=\E[20;2~,
+ kf22=\E[21;2~, kf23=\E[23;2~, kf24=\E[24;2~,
+ kf25=\E[1;5P, kf26=\E[1;5Q, kf27=\E[1;5R, kf28=\E[1;5S,
+ kf29=\E[15;5~, kf3=\EOR, kf30=\E[17;5~, kf31=\E[18;5~,
+ kf32=\E[19;5~, kf33=\E[20;5~, kf34=\E[21;5~,
+ kf35=\E[23;5~, kf36=\E[24;5~, kf37=\E[1;6P, kf38=\E[1;6Q,
+ kf39=\E[1;6R, kf4=\EOS, kf40=\E[1;6S, kf41=\E[15;6~,
+ kf42=\E[17;6~, kf43=\E[18;6~, kf44=\E[19;6~,
+ kf45=\E[20;6~, kf46=\E[21;6~, kf47=\E[23;6~,
+ kf48=\E[24;6~, kf49=\E[1;3P, kf5=\E[15~, kf50=\E[1;3Q,
+ kf51=\E[1;3R, kf52=\E[1;3S, kf53=\E[15;3~, kf54=\E[17;3~,
kf55=\E[18;3~, kf56=\E[19;3~, kf57=\E[20;3~,
kf58=\E[21;3~, kf59=\E[23;3~, kf6=\E[17~, kf60=\E[24;3~,
kf61=\E[1;4P, kf62=\E[1;4Q, kf63=\E[1;4R, kf7=\E[18~,
colors#8, cols#80, it#8, lines#24, ncv#3, pairs#64,
acsc=``aaffggiijjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bel=^G, bold=\E[1m, civis=\E[?25l, clear=\E[H\E[2J,
- cnorm=\E[?12l\E[?25h, cr=^M, csr=\E[%i%p1%d;%p2%dr,
- cub1=^H, cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cnorm=\E[?12l\E[?25h, cr=\r, csr=\E[%i%p1%d;%p2%dr,
+ cub1=^H, cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J, el=\E[K,
home=\E[H, hpa=\E[%i%p1%dG, ht=^I, ich=\E[%p1%d@,
- il=\E[%p1%dL, il1=\E[L, ind=^J, indn=\E[%p1%dS, kbs=\177,
+ il=\E[%p1%dL, il1=\E[L, ind=\n, indn=\E[%p1%dS, kbs=^?,
kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
kdch1=\E[3~, kend=\E[4~, kf1=\EOP, kf10=\E[21~,
kf11=\E[23~, kf12=\E[24~, kf2=\EOQ, kf3=\EOR, kf4=\EOS,
colors#256, cols#80, it#8, lines#24, lm#0, pairs#32767,
acsc=``aaffggjjkkllmmnnooppqqrrssttuuvvwwxxyyzz{{||}}~~,
bold=\E[1m, civis=\E[?25l, clear=\E[H\E[2J,
- cnorm=\E[?25h, cr=^M, csr=\E[%i%p1%d;%p2%dr,
- cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=^J,
+ cnorm=\E[?25h, cr=\r, csr=\E[%i%p1%d;%p2%dr,
+ cub=\E[%p1%dD, cub1=^H, cud=\E[%p1%dB, cud1=\n,
cuf=\E[%p1%dC, cuf1=\E[C, cup=\E[%i%p1%d;%p2%dH,
cuu=\E[%p1%dA, cuu1=\E[A, dch=\E[%p1%dP, dch1=\E[P,
dl=\E[%p1%dM, dl1=\E[M, ed=\E[J, el=\E[K, el1=\E[1K,
enacs=\E(B\E)0, flash=^G, home=\E[H, hpa=\E[%i%p1%dG,
- ht=^I, hts=\EH, il=\E[%p1%dL, il1=\E[L, ind=^J,
+ ht=^I, hts=\EH, il=\E[%p1%dL, il1=\E[L, ind=\n,
is1=\E[?47l\E=\E[?1l,
is2=\E[r\E[m\E[2J\E[H\E[?7h\E[?1;3;4;6l\E[4l, kbs=^H,
kcub1=\E[D, kcud1=\E[B, kcuf1=\E[C, kcuu1=\E[A,
cbunix|cb unix virtual terminal,
OTbs, am, da, db,
cols#80, lines#24, lm#0,
- bel=^G, clear=\EL, cr=^M, cub1=^H, cud1=^J, cuf1=\EC,
+ bel=^G, clear=\EL, cr=\r, cub1=^H, cud1=\n, cuf1=\EC,
cup=\EG%p2%c%p1%c, cuu1=\EA, dch1=\EM, dl1=\EN, ed=\EL,
- el=\EK, ich1=\EO, il1=\EP, ind=^J, kcub1=\ED, kcud1=\EB,
+ el=\EK, ich1=\EO, il1=\EP, ind=\n, kcub1=\ED, kcud1=\EB,
kcuf1=\EC, kcuu1=\EA, khome=\EE, rmso=\Eb^D, rmul=\Eb^A,
smso=\Ea^D, smul=\Ea^A,
# (vremote: removed obsolete ":nl@:" -- esr)
eterm|gnu emacs term.el terminal emulation,
am, mir, xenl,
cols#80, lines#24,
- bel=^G, bold=\E[1m, clear=\E[H\E[J, cr=^M,
+ bel=^G, bold=\E[1m, clear=\E[H\E[J, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J,
el=\E[K, el1=\E[1K, home=\E[H, ht=^I, ich=\E[%p1%d@,
- il=\E[%p1%dL, il1=\E[L, ind=^J, rev=\E[7m,
+ il=\E[%p1%dL, il1=\E[L, ind=\n, rev=\E[7m,
rmcup=\E[2J\E[?47l\E8, rmir=\E[4l, rmso=\E[m, rmul=\E[m,
sgr0=\E[m, smcup=\E7\E[?47h, smir=\E[4h, smso=\E[7m,
smul=\E[4m,
eterm-color|Emacs term.el terminal emulator term-protocol-version 0.96,
am, mir, msgr, xenl,
colors#8, cols#80, lines#24, pairs#64,
- bel=^G, blink=\E[5m, bold=\E[1m, clear=\E[H\E[J, cr=^M,
+ bel=^G, blink=\E[5m, bold=\E[1m, clear=\E[H\E[J, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J,
el=\E[K, el1=\E[1K, home=\E[H, ht=^I, ich=\E[%p1%d@,
- il=\E[%p1%dL, il1=\E[L, ind=^J, invis=\E[8m, kbs=\177,
+ il=\E[%p1%dL, il1=\E[L, ind=\n, invis=\E[8m, kbs=^?,
kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC, kcuu1=\EOA,
kdch1=\E[3~, kend=\E[4~, khome=\E[1~, kich1=\E[2~,
knp=\E[6~, kpp=\E[5~, op=\E[39;49m, rc=\E8, rev=\E[7m,
dumb-emacs-ansi|Emacs dumb terminal with ANSI color codes,
am, hc,
colors#8, it#8, ncv#13, pairs#64,
- bold=\E[1m, cud1=^J, ht=^I, ind=^J, op=\E[39;49m,
+ bold=\E[1m, cud1=\n, ht=^I, ind=\n, op=\E[39;49m,
ritm=\E[23m, rmul=\E[24m, setab=\E[4%p1%dm,
setaf=\E[3%p1%dm, sgr0=\E[m, sitm=\E[3m, smul=\E[4m,
acsc=++\,\,--..00``aaffgghhiijjkkllmmnnooppqqrrssttuuvvwwxxy
yzz{{||}}~~,
bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z, civis=\E[?25l,
- clear=\E[H\E[J, cnorm=\E[34h\E[?25h, cr=^M,
+ clear=\E[H\E[J, cnorm=\E[34h\E[?25h, cr=\r,
csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\EM,
cvvis=\E[34l, dch=\E[%p1%dP, dch1=\E[P, dim=\E[2m,
dl=\E[%p1%dM, dl1=\E[M, ed=\E[J, el=\E[K, el1=\E[1K,
enacs=\E(B\E)0, flash=\Eg, home=\E[H, ht=^I, hts=\EH,
- ich=\E[%p1%d@, il=\E[%p1%dL, il1=\E[L, ind=^J, is2=\E)0,
+ ich=\E[%p1%d@, il=\E[%p1%dL, il1=\E[L, ind=\n, is2=\E)0,
kbs=^H, kcbt=\E[Z, kcub1=\EOD, kcud1=\EOB, kcuf1=\EOC,
kcuu1=\EOA, kdch1=\E[3~, kend=\E[4~, kf1=\EOP, kf10=\E[21~,
kf11=\E[23~, kf12=\E[24~, kf2=\EOQ, kf3=\EOR, kf4=\EOS,
# fix the backspace key
screen.linux|screen in linux console,
bw,
- kbs=\177, kcbt@, use=screen+fkeys, use=screen,
+ kbs=^?, kcbt@, use=screen+fkeys, use=screen,
screen.mlterm|screen in mlterm,
use=screen+fkeys, use=mlterm,
screen.putty|screen in putty,
screen2|old VT 100/ANSI X3.64 virtual terminal,
cols#80, it#8, lines#24,
- cbt=\E[Z, clear=\E[2J\E[H, cr=^M, cub=\E[%p1%dD, cub1=^H,
+ cbt=\E[Z, clear=\E[2J\E[H, cr=\r, cub=\E[%p1%dD, cub1=^H,
cud=\E[%p1%dB, cud1=\E[B, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\E[A,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J,
el=\E[K, ht=^I, hts=\EH, ich=\E[%p1%d@, ich1=, il=\E[%p1%dL,
- il1=\E[L, ind=^J, kbs=^H, kcub1=\ED, kcud1=\EB, kcuf1=\EC,
+ il1=\E[L, ind=\n, kbs=^H, kcub1=\ED, kcud1=\EB, kcuf1=\EC,
kcuu1=\EA, kf0=\E~, kf1=\ES, kf2=\ET, kf3=\EU, kf4=\EV,
kf5=\EW, kf6=\EP, kf7=\EQ, kf8=\ER, kf9=\E0I, khome=\EH,
- nel=^M^J, rc=\E8, ri=\EM, rmir=\E[4l, rmso=\E[23m,
+ nel=\r\n, rc=\E8, ri=\EM, rmir=\E[4l, rmso=\E[23m,
rmul=\E[24m, rs1=\Ec, sc=\E7, sgr0=\E[m, smir=\E[4h,
smso=\E[3m, smul=\E[4m, tbc=\E[3g,
# (screen3: removed unknown ":xv:LP:G0:" -- esr)
km, mir, msgr,
cols#80, it#8, lines#24,
bel=^G, blink=\E[5m, bold=\E[1m, cbt=\E[Z, clear=\E[H\E[J,
- cr=^M, csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
- cud=\E[%p1%dB, cud1=^J, cuf=\E[%p1%dC, cuf1=\E[C,
+ cr=\r, csr=\E[%i%p1%d;%p2%dr, cub=\E[%p1%dD, cub1=^H,
+ cud=\E[%p1%dB, cud1=\n, cuf=\E[%p1%dC, cuf1=\E[C,
cup=\E[%i%p1%d;%p2%dH, cuu=\E[%p1%dA, cuu1=\EM,
dch=\E[%p1%dP, dch1=\E[P, dl=\E[%p1%dM, dl1=\E[M, ed=\E[J,
el=\E[K, home=\E[H, ht=^I, hts=\EH, ich=\E[%p1%d@,
- il=\E[%p1%dL, il1=\E[L, ind=^J, is2=\E)0, kbs=^H, kcub1=\EOD,
+ il=\E[%p1%dL, il1=\E[L, ind=\n, is2=\E)0, kbs=^H, kcub1=\EOD,
&n
projects / ncurses.git / commitdiff